Sony MHC-V5 Service Manual ▷ View online
MHC-V5
29
2-25. USB BOARD BLOCK
4 filament tape
(sub
material)
(US, Australian)
filament tape
(sub material)
(sub material)
USB board
5 flexible flat
cable
(4P)
(CN2202)
6 USB board block
Wire setting
2 coating clip
1 screw
(BVTP3
u 8)
1 two screws
(BVTP3
u 8)
1 three screws
(BVTP3
u 8)
)errite FRre ()&) setting
cushion (E 0.5)
ferrite core (FC3)
guide line
Wrap once.
3 Remove the USB board block
in the direction of the arrow.
Note: When installing the flexible flat cable, ensure that
the colored line is not slanted after insertion.
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
to USB board
Terminal
face
face
– )rRnt Sanel rear view –
Ver. 1.3
MHC-V5
30
2-26. NFC MODULE (NFC1)
5 filament tape
(sub
material)
9 NFC module
(NFC1)
WireVeWWiQJ
filament tape
(sub material)
(sub material)
NFC module block
8 NFC holder
2 screw
(BVTP3
u 8)
6 flexible flat cable (8P)
(FFC6)
NFC module
block
block
NFC module
block
block
flexible flat cable (8P)
(FFC6)
(FFC6)
1 cushion (H)
cushion (H)
3 Peel off the adhesive sheet (NFC).
7 Peel off the
tape
(NFC).
long
Note 1: When installing the flexible flat cable, ensure that
the colored line is not slanted after insertion.
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
WireVeWWiQJ
4 Remove the NFC module block
in the direction of the arrow.
WireVeWWiQJ
OK
NG
Terminal face is
below side
below side
Terminal face
short
to
NFC module
(NFC1)
NFC module
(NFC1)
–)rRQWSDQeOreDrYieZ–
Note 2: Cushion (H) is deleted
from the midway of
production.
Ver. 1.1
MHC-V5
31
2-27. FFC HOLDER
1 two screws
(BVTP3
u 8)
2 CD mechanism deck block
1 two screws
(BVTP3
u 8)
cushion (H)
FFC holder
3 cushion (H)
boss
boss
claw
5 Draw out the flexible flat
cable (24P) from hole.
4 Remove the
FFC
holder
in the direction
of the arrow.
– CD mechanism deck block bottom view –
6 FFC holder
Note: When installing the FFC holder,
check that installed firmly
two bosses and claw.
hole
+ow to install the ))C holdeU
3astinJ Sosition oI cXshion +
There is a gap.
There is no gap.
OK
NG
–Bottom view –
MHC-V5
32
2-28. OPTICAL PICK-UP BLOCK (CMS-S76RFS7G) (OP1)
5 insulator
screw
screw
5 insulator screw
5 insulator
screw
screw
5 insulator screw
8 flexible flat cable (24P)
(FFC1)
(FFC1)
9 connector
7 connector
0 insulator
0 insulator
0 insulator
0 insulator
qa optical pick-up block
(CMS-S76RFS7G)
(OP1)
(CMS-S76RFS7G)
(OP1)
6 Remove the optical pick-up block
in the direction of the arrow.
4 three
claws
claws
WireVeWWiQJ
)Oe[iEOeIODWFDEOe3VeWWiQJ
1 claw
1 claw
1 claw
1 two
claws
claws
1 claw
2 chuck holder block
±BRWWRPYieZ–
Note 1: When installing the flexible flat cable, ensure that
the colored line is not slanted after insertion.
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note 2: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
OK
NG
NG
terminal face is below side.
–
7RSYieZ–
3 Draw out the tray.
Note
Note
3:
When you can not draw out the tray,
please refer to “HOW TO OPEN THE TRAY
WHEN POWER SWITCH TURN OFF” on page 6.
Click on the first or last page to see other MHC-V5 service manuals if exist.