Sony MDS-JA555ES Service Manual ▷ View online
17
3-6. BU HOLDER ASSEMBLY
3-7. MOTOR (LOADING) ASSEMBLY (M10)
2
Two scews
(BV2.6)
(BV2.6)
2
Two scews
(BV2.6)
(BV2.6)
3
Two collars
(damper)
3
Two collars
(damper)
4
Two compression
springs
4
Two compression
springs
5
BU holder assembly
1
Turn the pully gear to align
the slider with of the rib.
(Refer to Fig. A.)
(Refer to Fig. A.)
Fig. A
Slider
Rib
2
Two screws
(BV2.6)
(BV2.6)
4
Belt (loading)
3
Gear assembly
6
Motor (loading) assembly (M10)
5
Two screws
(B2
(B2
×
3)
1
Connector
(CN14)
(CN14)
18
3-8. BASE UNIT (MBU-5C)
3-9. BD BOARD
A
4
Two screws
(BV2.6)
(BV2.6)
2
Leaf spring (UDR)
1
Leaf spring (UDL)
4
Two screws
(BV2.6)
(BV2.6)
5
Base unit
3
Remove the holder assembly
in the direction of the arrow
A
.
5
Two precision screws
(+P1.7
(+P1.7
×
2.5)
4
Tapping screw
(M1.7)
3
Flexible board
(CN104)
(CN104)
3
Flexible board
(CN101)
(CN101)
7
BD board
6
Claw
2
Remove the soldering
from the push switch.
1
Remove the soldering of
the lead wires from
the spindle motor assembly.
the spindle motor assembly.
19
3-10. OVER LIGHT HEAD (HR901)
3-11. MINI DISC DEVICE (KMS-260B/J1N)
2
Screw
(P1.7
(P1.7
×
6)
1
Flexible board
(CN104)
(CN104)
3
Over light head
(HR901)
2
Screw +B
(B2
(B2
×
8)
1
Flexible board (CN104)
1
Flexible board (CN101)
3
Leaf spring (shaft)
4
Main shaft
5
Remove the mini disc device (KMS-260B/J1N)
in the direction of the arrow
A
.
A
20
SECTION 4
TEST MODE
4-1. Precaution on Using the Test Mode
•
Be sure to insert and eject a disc after confirming that the disc in the MDS-JA555ES has come to complete stop because the loading
related movements of the mechanism are performed without any relationship with the test mode.
Disc does not stop rotating even through the A button is pressed while disc is rotating in the modes such as continuous playback and
continuous recording. Therefore, the disc is ejected while it is rotating.
Be sure to press the MENU/NO button, then press the A button after a disc has completely stopped of its rotation.
related movements of the mechanism are performed without any relationship with the test mode.
Disc does not stop rotating even through the A button is pressed while disc is rotating in the modes such as continuous playback and
continuous recording. Therefore, the disc is ejected while it is rotating.
Be sure to press the MENU/NO button, then press the A button after a disc has completely stopped of its rotation.
4-1-1. Modes in Which Recording Laser Emits the Light and the Button Operations
•
Continuos recording mode (CREC MODE)
•
Laser power check mode (LDPWR CHECK)
•
Laser power adjustment mode (LDPWR ADJUST)
•
Traverse (MO) check (EF MO CHECK)
•
Traverse (MO) check (EF MO ADJUST)
•
When the zREC button is pressed
4-2. How to Enter the Test Mode
There are two methods to enter the test mode as follows.
Method 1: Connect the power plug to the outlet while pressing the lAMSL knob and x button at the same time, and remove the
Method 1: Connect the power plug to the outlet while pressing the lAMSL knob and x button at the same time, and remove the
lAMSL knob and x button at the same time.
When the unit enters the test mode, “[Check]” appears. The four groups can be switched, ......
When the unit enters the test mode, “[Check]” appears. The four groups can be switched, ......
↔
Check
↔
Adjust
↔
Service
↔
Develop
↔.....
, by rotating the lAMSL knob.
Method 2: Connect the power plug to the outlet while pressing the lAMSL knob, and remove the lAMSL knob.
When the unit enters the test mode, “TEMP CHECK” appears. When the test mode is entered using this method, the contents of
check group at method 1 can be performed.
check group at method 1 can be performed.
4-3. Exiting the Test Mode
Press the REPEAT button. The display and LEDs of the pitch control and the filter are turned off. The MDS-JA555ES enters the standby
status and exits the test mode.
status and exits the test mode.
4-4. Basic Operation of the Test Mode
All operations are performed using the lAMSL knob, YES button, and MENU/NO button.
The functions of these button are as follows.
The functions of these button are as follows.
Function
Contents
lAMSL knob
Changes parameters and modes
YES button
Proceeds onto the next step. Finalize input.
MENU/NO button
Returns to previous step. Stops operations.
Click on the first or last page to see other MDS-JA555ES service manuals if exist.