Sony ICD-SX712 / ICD-SX713 / ICD-SX813 Service Manual ▷ View online
ICD-SX712/SX712D/SX713/SX813
9
1-9. ORNAMENT (MIC)
1-10. CAP (MIC)
1 screw
2 two screws
(M
1.4)
3 ornament (MIC)
MIC sub assy
1 screw (1.4)
3 screw (1.4)
2 cap (MIC)
4 cap (MIC)
claw
claw
MIC sub assy
ICD-SX712/SX712D/SX713/SX813
10
1-12. COVER (MIC) (FRONT)
1-11. COVER (MIC) (REAR)
1 two special screws
(M
1.4)
2 MIC assy B
3 cover (MIC) (rear)
shaft
shaft
1 cover (MIC) (front)
ICD-SX712/SX712D/SX713/SX813
11
1-13. MICROPHONE ASSY (MIC101, MIC102)
5 MIC101
6 MIC102
1
blind sheet (MIC)
3
blind sheet (MIC)
2
holder (MIC) (upper)
4
holder (MIC) (upper)
holder (MIC) (bottom)
holder (MIC) (bottom)
ICD-SX712/SX712D/SX713/SX813
12
SECTION 2
TEST MODE
[Test Mode]
The following checks can be implemented using the Test Mode.
The following checks can be implemented using the Test Mode.
How to Enter the Test Mode
1. Turn the power on. (by inserting batteries)
2. Slide the [NOISE CUT] switch while pressing the [T-MARK]
1. Turn the power on. (by inserting batteries)
2. Slide the [NOISE CUT] switch while pressing the [T-MARK]
button and [VOL –] button at the same time.
3. Slide the [NOISE CUT] swith in the direction opposite to
that specifi ed in 2. while pressing the [T-MARK] button and
[VOL –] button at the same time.
[VOL –] button at the same time.
4. Slide the [NOISE CUT] swith in the direction opposite to
that specifi ed in 3. while pressing the [T-MARK] button and
[VOL –] button at the same time.
[VOL –] button at the same time.
How to Exit the Test Mode
Exit the test mode by turning OFF the power. (by removing the
batteries)
Exit the test mode by turning OFF the power. (by removing the
batteries)
Initial Status of the Test Mode
When the machine enters the test mode, the LCD display appears
as shown below.
When the machine enters the test mode, the LCD display appears
as shown below.
<TEST MODE MENU>
Version
KeyChk+Fmt
Loop
IntMic Sens
Beep
KeyChk+Fmt
Loop
IntMic Sens
Beep
Operation of the Test Mode
Select the desired item by using the [
Select the desired item by using the [
>
]/[
.
] button, and press
the [
N
/ ENT] button to set the selection.
.
>
Pressing the [T-MARK] and
[VOL-] button at the same time.
Slided on the
[NOISE CUT] switch.
Slided on the
[NOISE CUT] switch.
Slided on the
[NOISE CUT] switch.
SERVICE MODE start
MENU display
START
After turn on power
stop or sleep condition
END
TEST MODE
Turn off the power
(Remove the batteries)
Version
KeyChk+Fmt
J
j
IntMic Sens
Lcd Contrast
Loop
Beep
Cluster Num
RTC Int
BattCnt
BattBC4
Battery
BattAC2
VBUS
Sleep
dnc GAIN
Log Output
IntMic CLEAR
App LogOut
Menu init
Convert
Factory Ship
Key Check
Version
Click on the first or last page to see other ICD-SX712 / ICD-SX713 / ICD-SX813 service manuals if exist.