Sony HT-ST5 Service Manual ▷ View online
HT-ST5
9
2-5. RF MODULATOR (WS001) (RFM1)
3 housing (top) assy
2 two claws
2 two claws
guide pin
guide pin
1 cushion
(QV,
(QV,
B)
ditch
ditch
6 flexible flat cable (26P)
(FFC7)
(FFC7)
flexible flat cable
(26P)
(FFC7)
(26P)
(FFC7)
filament tape
(sub material)
(sub material)
terminal
side
side
terminal
side
side
)OH[LEOHIODWFDEOH3))&VHWWLQJ
5 filament tape
(sub
(sub
material)
7 RF modulator (WS001)
(RFM1)
(RFM1)
RF modulator
(WS001)
(RFM1)
(WS001)
(RFM1)
–
5HDUSDQHO/EORFNIURQWYLHZ–
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
Note 2: When installing the flexible
flat cable, ensure that the
colored line is parallel to the
connector after insertion.
4 RF modulator (WS001) (RFM1)
Note
Note
1: When installing the RF modulator block
(WS001) (RFM1), align four ditches
and four guide pins.
Blue reinforcement
board is short.
board is short.
Blue reinforcement
board is long.
board is long.
HT-ST5
10
2-6. BRACKET BOTTOM BLOCK
Note: Please spread a sheet under a unit
not to injure grille assy.
Please work carefully so as not to
damage the grille assy.
– Rear bottom view –
5 boss
6 claw
5 boss
5 boss
5 boss
5 boss
7 bracket (arm)
7 bracket (arm)
7 bracket (arm)
7 bracket arm assy
7 bracket arm assy
6 claw
4 screw
(BV/ring)
(BV/ring)
4 screw
(BV/ring)
(BV/ring)
4 screw
(BV/ring)
(BV/ring)
4 screw
(BV/ring)
(BV/ring)
4 screw
(BV/ring)
(BV/ring)
6 claw
6 claw
6 claw
1 screw
(B3
(B3
u 8)
1 screw
(B3
(B3
u 8)
2 foot (ANG) assy
3 screw
(truss/ring)
(truss/ring)
3 screw
(truss/ring)
(truss/ring)
3 screw
(truss/ring)
(truss/ring)
3 screw
(truss/ring)
(truss/ring)
3 screw
(truss/ring)
(truss/ring)
3 screw
(truss/ring)
(truss/ring)
2 foot (ANG) assy
qd bracket bottom block
qs boss
qa guide pin
qa guide pin
9 bracket air assy
8 four screws
(BVTP3
(BVTP3
u 8)
0 three screws
(BV/ring)
(BV/ring)
0 three screws
(BV/ring)
(BV/ring)
0 nine screws
(BV/ring)
(BV/ring)
HT-ST5
11
2-7. POWER CORD (AC1)
6 cord bushing (FBS001)
7 power cord
(AC1)
(AC1)
5 claw
– Rear bottom view –
3ower ForG VettiQJ
power cord
(AC1)
(AC1)
cord bushing
(FBS001)
(FBS001)
claw
150 +5, -0 mm
to POWER board
Note 2: When installing the power cord (AC1),
check the direction of claw of cord bushing
(FBS001) and install correctly.
4 Remove the cord bushing (FBS001)
in the direction of the arrow.
1 Remove the power cord
from the clamp (L35).
2 power cord connector
(CN501)
(CN501)
3 Draw out the power cord connector.
3ower ForG $& VettiQJ
clamp (L35)
power cord
(AC1)
(AC1)
POWER board
Note 1: Please spread a sheet under a unit
not to injure grille assy.
Please work carefully so as not to
damage the grille assy.
HT-ST5
12
2-8. CHASSIS BLOCK
– Rear bottom view –
9 flexible flat cable (14P)
(CN902)
(CN902)
3 connector
(CN3006)
(CN3006)
2 connector
(CN3007)
(CN3007)
4 connector
(CN3002)
(CN3002)
5 connector
(CN3003)
(CN3003)
7 flexible flat cable (8P)
(CN1002)
(CN1002)
6 filament tape
(sub
(sub
material)
6 filament tape
(sub
(sub
material)
6 filament tape
(sub
(sub
material)
8 flexible flat cable (5P)
(CN1007)
(CN1007)
1 flexible flat cable (15P)
(CN1005)
(CN1005)
qa chassis block
0 five screws
(BVTP3
(BVTP3
u 8)
A
A
filament tape
(sub material)
(sub material)
filament tape
(sub material)
(sub material)
filament tape
(sub material)
(sub material)
MAIN board
:LUHVHWWLQJ
MAIN board
Check that wires are not sticking out.
:LUHVHWWLQJ
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
Note 2: When installing the flexible flat cable,
ensure that the colored line is parallel
to the connector after insertion.
Note 1: Please spread a sheet under a unit
not to injure grille assy.
Please work carefully so as not to
damage the grille assy.
Click on the first or last page to see other HT-ST5 service manuals if exist.