Sony HT-ST5 Service Manual ▷ View online
HT-ST5
21
2-18. RC-S801 (NFC1)
2-19. RIGHT SPEAKER BLOCK
3 flexible flat cable (8P)
5&61)&VHWWLQJ
–
5HDUWRSYLHZ–
–
5LJKWYLHZ–
push
boss
RC-S801
(NFC1)
(NFC1)
4 RC-S801 (NFC1)
2 Remove the RC-S801
block in the direction
of the arrow.
–
,QVLGHYLHZ–
flexible flat cable
(8P) (FFC6)
(8P) (FFC6)
blue (reinforcement
board) side
board) side
guide line
RC-S801 (NFC1)
1 Peel off the RC-S801 (NFC1)
from two adhesive sheets.
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
1*
Note 2: When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
Note 1: Please spread a sheet under a unit
not to injure grille assy.
Please work carefully so as not to
damage the grille assy.
guide
pin
pin
– Rear bottom view –
1 four screws
(BTP2.6
(BTP2.6
u 8)
2 LID (button)
ditch
Note 2: When installing the
right
right
speaker
block,
align the guide pin
and
ditch.
guide pin
ditch
Note 1: Please spread a sheet under a unit
not to injure grille assy.
Please work carefully so as not to
damage the grille assy.
6 right speaker block
5 three screws
(BVTP
(BVTP
3
u 10)
4 two tapping screws
(PWH3
(PWH3
u 8)
3 cushion (front)
HT-ST5
22
2-20. BLUETOOTH MODULE (BT1)
7 screw
(BVTP3
(BVTP3
u 10)
3 screw
(BVTP3
(BVTP3
u 10)
8 Bluetooth module
(BT1)
(BT1)
5 Remove the bluetooth module block
in the direction of the arrow.
4 boss
6 flexible flat cable
(14P)
(14P)
2 cushion (H10)
push
1 filament tape
(sub
(sub
material)
– Right view –
flexible flat cable
(14P)
(14P)
Bluetooth module (BT1)
Flexible flat cable (14P) setting
cushion (H10)
filament tape
(sub material)
(sub material)
– Right speaker block rear bottom view –
blue (reinforcement
board) side
board) side
HT-ST5
23
2-21. DISPLAY BOARD
7 flexible flat cable (15P)
(CN801)
(CN801)
5 screw (BVTP3 u 12)
5 screw
(BVTP3
(BVTP3
u 12)
9 two claws
0 holder (LED) assy
8 collar (damper)
8 collar (damper)
qa bushing (damper)
qa bushing (damper)
qa bushing
(damper)
(damper)
8 collar (damper)
6 Remove the DISPLAY board block
in the direction of the arrow.
qs DISPLAY board
qa bushing (damper)
8 collar (damper)
5 screw
(BVTP3
(BVTP3
u 12)
5 screw
(BVTP3
(BVTP3
u 12)
)OH[LEOHIODWFDEOHVHWWLQJ
cushion (H10)
cushion (H10)
1 canoe clip (small)
1 canoe clip (small)
3 jack sheet
jack sheet
4 cushion (H10)
2 Peel off two adhesive sheets.
guide line
-DFNVKHHWVHWWLQJ
–
5LJKWVSHDNHUEORFNIURQWERWWRPYLHZ–
flexible flat cable (15P) (FFC2)
flexible flat cable (14P) (FFC5)
–
5LJKWVSHDNHUEORFNUHDUERWWRPYLHZ–
HT-ST5
24
2-22. CABINET (RIGHT) BLOCK
2 eight screws
(3.5
(3.5
u 12)
2 two screws
(3.5
(3.5
u 12)
3 cabinet (right) block
:LUHVHWWLQJ
cushion (H10)
cushion (H10)
hook
hook
:LUHVHWWLQJ
flexible flat cable (14P) (FFC5)
1 Remove the speaker cable (R-ch)
from two hooks of right speaker block.
–
5LJKWVSHDNHUEORFNUHDUERWWRPYLHZ–
Click on the first or last page to see other HT-ST5 service manuals if exist.