Sony HT-ST3 Service Manual ▷ View online
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
HT-ST3
77
< CONNECTOR >
* CN751
1-580-055-21 PIN, CONNECTOR (SMD) 2P
< SWITCH >
S751 1-786-653-21 SWITCH,
TACTILE
(?/1)
*************************************************************
SP
TERMINAL
BOARD
*****************
< CAPACITOR >
C3201 1-118-290-11 CERAMIC
CHIP 0.001uF 10% 50V
C3202 1-118-290-11 CERAMIC
CHIP 0.001uF 10% 50V
C3203 1-118-290-11 CERAMIC
CHIP 0.001uF 10% 50V
C3204 1-118-290-11 CERAMIC
CHIP 0.001uF 10% 50V
C3205 1-118-290-11 CERAMIC
CHIP 0.001uF 10% 50V
C3206 1-118-290-11 CERAMIC
CHIP 0.001uF 10% 50V
C3207 1-118-290-11 CERAMIC
CHIP 0.001uF 10% 50V
C3208 1-118-290-11 CERAMIC
CHIP 0.001uF 10% 50V
< CONNECTOR >
CN3101 1-691-766-11 PLUG (MICRO CONNECTOR) 4P
CN3102 1-691-767-11 PLUG (MICRO CONNECTOR) 5P
CN3102 1-691-767-11 PLUG (MICRO CONNECTOR) 5P
< LUG TERMINAL >
* ET3101 1-780-408-11 TERMINAL, LUG
* ET3102 1-780-408-11 TERMINAL, LUG
* ET3102 1-780-408-11 TERMINAL, LUG
<
TERMINAL
>
TB3101 1-780-454-11 TERMINAL BOARD (SPEAKER) 4P
(ONLY FOR SS-ST3 SPEAKERS CENTER L/
CENTER R/FRONT L/FRONT R)
************************************************************
MISCELLANEOUS
**************
0 AC1
1-834-966-41 POWER-SUPPLY CORD (AEP, E41, SP)
0 AC1
1-835-068-21 CORD, POWER (AUS)
0 AC1
1-839-999-21 POWER-SUPPLY CORD (UK)
BT1
1-490-558-51 BLUETOOTH
MODULE
0 F501
1-576-232-51 FUSE (H.B.C.) (T 5 AH/250 V)
FC1
1-482-193-11 FERRITE CORE (GFPC-18-8-2)
FC2
1-482-193-11 FERRITE CORE (GFPC-18-8-2)
FFC1
9-833-606-25 WIRE KIT (FFC) (9 pin) (See Note)
FFC2
9-833-606-25 WIRE KIT (FFC) (22 pin) (See Note)
FFC3
9-833-606-25 WIRE KIT (FFC) (20 pin) (See Note)
FFC4
9-833-606-25 WIRE KIT (FFC) (14 pin) (See Note)
FFC5
9-833-606-25 WIRE KIT (FFC) (24 pin) (See Note)
FFC6
9-833-606-25 WIRE KIT (FFC) (8 pin) (See Note)
NFC1
8-989-470-00 RC-S801/A (NFC module)
SP1
1-858-897-11 LOUDSPEAKER (10X15 cm) (Subwoofer)
(Left Side)
SP2
1-858-897-11 LOUDSPEAKER (10X15 cm) (Subwoofer)
(Right Side)
************************************************************
Note: As for WIRE KIT (FFC), all fl at fl exible cables (Ref. No.
FFC1, FFC2, FFC3, FFC4, FFC5, FFC6) will be 1 set.
ACCESSORIES
************
4-467-146-11 INSTRUCTION MANUAL (Operating Instructions)
(ENGLISH) (UK, E41, AUS)
4-467-146-21 INSTRUCTION MANUAL (Operating Instructions)
(FRENCH, SPANISH, DUTCH) (AEP)
4-467-146-31 INSTRUCTION MANUAL (Operating Instructions)
(GERMAN, POLISH, ITALIAN) (AEP)
4-467-146-41 INSTRUCTION MANUAL (Operating Instructions)
(ENGLISH, TRADITIONAL CHINESE) (SP)
4-467-147-11 MANUAL, INSTRUCTION (RG) (Reference Guide)
(ENGLISH, FRENCH, SPANISH, DUTCH,
GERMAN, POLISH, ITALIAN,
TRADITIONAL CHINESE)
501
1-492-449-11 REMOTE COMMANDER (RM-ANU164)
(Remote control)
502
4-467-175-01 STAND (S) (1 piece) (Stand)
503
4-465-042-01 CUSHION, FOOT (1 piece) (Speaker pad)
504
4-972-322-11 FOOT (Y) (2 pieces, 1 set) (Speaker cushions)
(For installing the Bar Speaker on a wall)
505
1-837-197-31 CORD, LIGHT PLUG (Digital optical cable for a TV)
501
Remote control (1)
502
Stands (2)
503
Speaker pads (4)
504
Speaker cushions (2)
(For installing the Bar Speaker on a wall)
505
Digital optical cable for a TV (1)
POWER KEY
SP TERMINAL
HT-ST3
REVISION HISTORY
Ver.
Date
Description of Revision
1.0
2013.09
New
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
e.g.) If a contact point is shown as
, follow the procedure below.
Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.
HT-ST3
REVISION HISTORY
Ver.
Date
Description of Revision
1.0
2013.09
New
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
e.g.) If a contact point is shown as
, follow the procedure below.
Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.
HT-ST3
REVISION HISTORY
Ver.
Date
Description of Revision
1.0
2013.09
New
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF fi le search function to fi nd one.
e.g.) If a contact point is shown as
, follow the procedure below.
Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.