Sony HT-ST3 Service Manual ▷ View online
HT-ST3
49
Pin No.
Pin Name
I/O
Description
1
SIRCS_IN
I
SIRCS signal input from the remote control receiver
2
TP_LED
O
LED drive signal output terminal for the Bluetooth indicator “H”: LED on
3
DSP MOSI
O
Serial data output to the DSP and serial fl ash
4
DSP MISO
I
Serial data input from the DSP and serial fl ash
5
DSP_SPICLK
O
Serial data transfer clock signal output to the DSP and serial fl ash
6
BYTE
I
External data bus width selection signal input terminal Fixed at “L” in this unit
7
CNVss
I
Processor mode selection signal input terminal
8
ROM_SDA
I/O
Two-way data bus with the EEPROM
9
ROM_SCLK
O
Serial data transfer clock signal output to the EEPROM
10
RESET
I
System reset signal input terminal “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it change to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it change to “H”
11
Xout
O
System clock output terminal (8 MHz)
12
Vss
-
Ground terminal
13
Xin
I
System clock input terminal (8 MHz)
14
Vcc1
-
Power supply terminal (+3.3V)
15
CEC (I/O)
I/O
Two-way CEC serial data with the HDMI connector
16
DIR_ZERO
I
Zero data detection signal input from the digital audio interface receiver
17
RFDET_NFC
I
Magnetic fi eld detection signal input from the NFC module “L”: magnetic fi eld is detected
18
DRIVE_SD (DIAG)
I
Shut down signal input from the digital power amplifi er “L”: shut down
19 to 22
N.A.
O
Not used
23
HDMI_TX_5VPWR
O
+5V power on/off control signal output terminal for the HDMI TV OUT (ARC) connector
“H”: power on
“H”: power on
24
HDMI_NON_LPCM
O
Audio setting signal output terminal “L”: LPCM audio, “H”: HBR audio
25
DIR ERROR
I
Error detection signal input from the digital audio interface receiver “L”: error
26
N.A.
O
Not used
27
DAMP_SCLO
O
Serial data transfer clock signal output to the stream processor
28
DAMP_SDAO
I/O
Two-way data bus with the stream processor
29
M_TX_OUT_DSP
O
Serial data output to the DSP
30
M_RX_IN_DSP
I
Serial data input from the DSP
31
SCD/CLK1
I
Serial data transfer clock signal input terminal for fl ash writing
32
BUSY/RTS1
I
Clear to send signal input from the Bluetooth module
33
MC_BT-TXD0
O
Serial data output to the Bluetooth module
34
MC_BT-RXD0
I
Serial data input from the Bluetooth module
35
N.A.
O
Not used
36
MC_BT_RTS
O
Return to send signal output to the Bluetooth module
37
N.A.
O
Not used
38
A_SEL0
O
Analog audio selection signal output terminal “L”: external analog input, “H”: Bluetooth
39
HOLD
I
Fixed at “L” in this unit
40, 41
N.A.
O
Not used
42
BT_RST
O
Reset signal output to the Bluetooth module “L”: reset
43
PCONT_BT
O
+3.3V power on/off control signal output terminal for the Bluetooth module “H”: power on
44
WR_Flash
I
Fixed at “H” in this unit
45
HDMI_SDA
I/O
Two-way I2C data bus with the HDMI transceiver
46
HDMI_SCL
O
I2C clock signal output to the HDMI transceiver
47
HDMI_MUTE_DET
O
HDMI muting on/off control signal input from the HDMI transceiver “H”: muting on
48
DSP_SPIDS
O
Chip select signal output to the DSP and serial fl ash
49
DSP_RESET
O
Reset signal output to the DSP “L”: reset
50
SF_HOLD_DSP
O
Hold signal output to the serial fl ash “L”: hold
51
DIR_HCE
O
Chip enable signal output to the digital audio interface receiver
52
DIR_XSTATE
I
Source clock selection monitor input from the digital audio interface receiver
53
DIR_RST
O
Reset signal output to the digital audio interface receiver “L”: reset
54
HDMI_RST
O
Reset signal output to the HDMI transceiver “L”: reset
55
HDMI_MUTE_ON
O
HDMI muting on/off control signal output terminal “H”: muting on
56
HDMI_INT
I
Interrupt signal input from the HDMI transceiver
57
SEL_HDMI
O
HDMI selection signal output terminal “H”: HDMI
58
FL_RESET
O
Reset signal output to the fl uorescent indicator tube “L”: reset
59
P_CONT3
O
Power on/off control signal output terminal for the fl uorescent indicator tube “H”: power on
• IC Pin Function Description
AMP BOARD IC1002 R5F3650NCDFB (SYSTEM CONTROLLER)
HT-ST3
50
Pin No.
Pin Name
I/O
Description
60
Vcc2
-
Power supply terminal (+3.3V)
61
N.A.
O
Not used
62
Vss
-
Ground terminal
63
P_CONT2
O
Power on/off control signal output terminal for the digital power amplifi er “H”: power on
64
P_CONT1
O
Power on/off control signal output terminal “H”: power on
65
N.A.
O
Not used
66
DSP_INTR
I
Interrupt request signal input from the DSP
67
DAMP_SOFT_MUTE
O
Soft muting on/off control signal output to stream processor “L”: muting on
68
DAMP_INIT
O
Reset signal output to the stream processor “L”: reset
69
DAMP_PDN
O
Power down signal output to the stream processor “L”: power down
70
N.A.
O
Not used
71
AC_CUT
I
AC cut detection signal input terminal “L”: AC cut is detected
72
KEY_INT
I
Key wake-up signal input terminal
73
BT_MUTE
I
Muting on/off control signal input from the Bluetooth module “L”: muting on
74
DC_DET
I
Speaker DC detection signal input terminal “L”: speaker DC is detected
75
FL_DATA
O
Serial data output to the fl uorescent indicator tube
76
FL_CS
O
Chip select signal output to the fl uorescent indicator tube
77
FL_CLK
O
Serial data transfer clock signal output to the fl uorescent indicator tube
78
PCONT_HDMI
O
Power on/off control signal output terminal for the HDMI section “H”: power on
79
N.A.
O
Not used
80
PCONT_DSP
O
Power on/off control signal output terminal for the DSP “H”: power on
81
SW_NFC
O
Standby control signal output to the NFC module “L”: standby
82
LED_PW
O
LED drive signal output terminal for the display off indicator “H”: LED on
83
IRQ_NFC
I
Radio data reception signal input from the NFC module
84
SEL_NFC
O
Data transmission direction and completion notice signal output to the NFC module
85
DATA_NFC
I/O
Two-way data bus with the NFC module
86
SPICLK_NFC
O
Serial data transfer clock signal output to the NFC module
87 to 89
N.A.
O
Not used
90
DESTINATION
I
Destination setting terminal
91
MODEL
I
Model setting terminal
92, 93
KEY2, KEY1
I
Top panel key input terminal (A/D input)
94
AVss
-
Ground terminal
95
KEY0
I
Power key input terminal (A/D input)
96
Vref
I
Reference voltage (+3.3V) input terminal
97
AVcc
-
Power supply terminal (+3.3V)
98
DIR_DO
(MC_DIR_DI)
I
Serial data input from the digital audio interface receiver
99
DIR_DI
(MC_DIR_DO)
O
Serial data output to the digital audio interface receiver
100
DIR_CLK
O
Serial data transfer clock signal output to the digital audio interface receiver
HT-ST3
51
AMP BOARD IC3506 SII9573CTUC (HDMI TRANSCEIVER)
Pin No.
Pin Name
I/O
Description
1 to 6
D14 to D19
I
Digital video signal input terminal Not used
7
DE
I
Data enable signal input terminal Not used
8
VSYNC
I
Vertical sync signal input terminal Not used
9
HSYNC
I
Horizontal sync signal input terminal Not used
10
R0XC–
I
TMDS clock (negative) signal input terminal Not used
11
R0XC+
I
TMDS clock (positive) signal input terminal Not used
12
R0X0–
I
TMDS data (negative) input terminal Not used
13
R0X0+
I
TMDS data (positive) input terminal Not used
14
R0X1–
I
TMDS data (negative) input terminal Not used
15
R0X1+
I
TMDS data (positive) input terminal Not used
16
R0X2–
I
TMDS data (negative) input terminal Not used
17
R0X2+
I
TMDS data (positive) input terminal Not used
18
AVDD12
-
Power supply terminal (+1.3V)
19
AVDD33
-
Power supply terminal (+3.3V)
20
R1XC–
I
TMDS clock (negative) signal input terminal Not used
21
R1XC+
I
TMDS clock (positive) signal input terminal Not used
22
R1X0–
I
TMDS data (negative) input terminal Not used
23
R1X0+
I
TMDS data (positive) input terminal Not used
24
R1X1–
I
TMDS data (negative) input terminal Not used
25
R1X1+
I
TMDS data (positive) input terminal Not used
26
R1X2–
I
TMDS data (negative) input terminal Not used
27
R1X2+
I
TMDS data (positive) input terminal Not used
28
R2XC–
I
TMDS clock (negative) signal input terminal Not used
29
R2XC+
I
TMDS clock (positive) signal input terminal Not used
30
R2X0–
I
TMDS data (negative) input terminal Not used
31
R2X0+
I
TMDS data (positive) input terminal Not used
32
R2X1–
I
TMDS data (negative) input terminal Not used
33
R2X1+
I
TMDS data (positive) input terminal Not used
34
R2X2–
I
TMDS data (negative) input terminal Not used
35
R2X2+
I
TMDS data (positive) input terminal Not used
36
AVDD12
-
Power supply terminal (+1.3V)
37
CVCC12
-
Power supply terminal (+1.3V)
38
AVDD33
-
Power supply terminal (+3.3V)
39
R3XC–
I
TMDS clock (negative) signal input from the HDMI IN 3 connector
40
R3XC+
I
TMDS clock (positive) signal input from the HDMI IN 3 connector
41
R3X0–
I
TMDS data (negative) input from the HDMI IN 3 connector
42
R3X0+
I
TMDS data (positive) input from the HDMI IN 3 connector
43
R3X1–
I
TMDS data (negative) input from the HDMI IN 3 connector
44
R3X1+
I
TMDS data (positive) input from the HDMI IN 3 connector
45
R3X2–
I
TMDS data (negative) input from the HDMI IN 3 connector
46
R3X2+
I
TMDS data (positive) input from the HDMI IN 3 connector
47
R4XC–
I
TMDS clock (negative) signal input from the HDMI IN 2 connector
48
R4XC+
I
TMDS clock (positive) signal input from the HDMI IN 2 connector
49
R4X0–
I
TMDS data (negative) input from the HDMI IN 2 connector
50
R4X0+
I
TMDS data (positive) input from the HDMI IN 2 connector
51
R4X1–
I
TMDS data (negative) input from the HDMI IN 2 connector
52
R4X1+
I
TMDS data (positive) input from the HDMI IN 2 connector
53
R4X2–
I
TMDS data (negative) input from the HDMI IN 2 connector
54
R4X2+
I
TMDS data (positive) input from the HDMI IN 2 connector
55
AVDD12
-
Power supply terminal (+1.3V)
56
AVDD33
-
Power supply terminal (+3.3V)
57
R5XC–
I
TMDS clock (negative) signal input from the HDMI IN 1 connector
58
R5XC+
I
TMDS clock (positive) signal input from the HDMI IN 1 connector
59
R5X0–
I
TMDS data (negative) input from the HDMI IN 1 connector
60
R5X0+
I
TMDS data (positive) input from the HDMI IN 1 connector
61
R5X1–
I
TMDS data (negative) input from the HDMI IN 1 connector
62
R5X1+
I
TMDS data (positive) input from the HDMI IN 1 connector
63
R5X2–
I
TMDS data (negative) input from the HDMI IN 1 connector
HT-ST3
52
Pin No.
Pin Name
I/O
Description
64
R5X2+
I
TMDS data (positive) input from the HDMI IN 1 connector
65
CVCC12
-
Power supply terminal (+1.3V)
66
CSCL
I
I2C clock signal input from the system controller
67
CSDA
I/O
Two-way I2C data bus with the system controller
68
INT
O
Interrupt signal output to the system controller
69
RESET
I
Reset signal input from the system controller “L”: reset
70
TPWR_CI2CA
I
Not used
71
CEC_A1
O
Not used
72
CEC_A0WAKEUP
O
Not used
73
DSDA6
I/O
Two-way I2C serial data bus terminal Not used
74
DSCL6
I
I2C serial data transfer clock signal input terminal Not used
75
LPSVCC33
I
Not used
76
DSDA0
I/O
Two-way I2C serial data bus terminal Not used
77
DSCL0
I
I2C serial data transfer clock signal input terminal Not used
78
CBUS_HPD0
O
Hot plug detection control signal output terminal Not used
79
R0PWR5V
I
Power supply voltage (+5V) input terminal Not used
80
DSDA1
I/O
Two-way I2C serial data bus terminal Not used
81
DSCL1
I
I2C serial data transfer clock signal input terminal Not used
82
CBUS_HPD1
O
Hot plug detection control signal output terminal Not used
83
R1PWR5V
I
Power supply voltage (+5V) input terminal Not used
84
DSDA2
I/O
Two-way I2C serial data bus terminal Not used
85
DSCL2
I
I2C serial data transfer clock signal input terminal Not used
86
CBUS_HPD2
O
Hot plug detection control signal output terminal Not used
87
R2PWR5V
I
Power supply voltage (+5V) input terminal Not used
88
DSDA3
I/O
Two-way I2C serial data bus with the HDMI IN 3 connector
89
DSCL3
I
I2C serial data transfer clock signal input from the HDMI IN 3 connector
90
CBUS_HPD3
O
Hot plug detection control signal output to the HDMI IN 3 connector
91
R3PWR5V
I
Power supply voltage (+5V) input from the HDMI IN 3 connector
92
DSDA4
I/O
Two-way I2C serial data bus with the HDMI IN 2 connector
93
DSCL4
I
I2C serial data transfer clock signal input from the HDMI IN 2 connector
94
CBUS_HPD4
O
Hot plug detection control signal output to the HDMI IN 2 connector
95
R4PWR5V
I
Power supply voltage (+5V) input from the HDMI IN 2 connector
96
RSVDL
I
Not used
97
DSDA5
I/O
Two-way I2C serial data bus with the HDMI IN 1 connector
98
DSCL5
I
I2C serial data transfer clock signal input from the HDMI IN 1 connector
99
CBUS_HPD5
O
Hot plug detection control signal output to the HDMI IN 1 connector
100
R5PWR5V
I
Power supply voltage (+5V) input from the HDMI IN 1 connector
101
SBVCC5V
-
Power supply terminal (+5V)
102
VCC33OUT
O
Power supply (+3.3V) output terminal
103, 104
GPIO0, GPIO1
I/O
Not used
105
TX_HPD0
I
Hot plug detection signal input terminal Not used
106
TXDSDA0
I/O
Two-way I2C serial data bus terminal Not used
107
TXDSCL0
O
I2C serial data transfer clock signal output terminal Not used
108
TX_HPD1
I
Hot plug detection signal input from the HDMI OUT TV ARC connector
109
TXDSDA1
I/O
Two-way I2C serial data bus with the HDMI OUT TV ARC connector
110
TXDSCL1
O
I2C serial data transfer clock signal output to the HDMI OUT TV ARC connector
111
APLL12
-
Power supply terminal (+1.3V)
112
XTALVCC33
-
Power supply terminal (+3.3V)
113
XTALOUT
O
System clock signal output terminal (27 MHz)
114
XTALIN
I
System clock signal input terminal (27 MHz)
115
XTALGND
-
Ground terminal
116
CVCC12
-
Power supply terminal (+1.3V)
117 to 120
GPIO2 to GPIO5
I/O
Not used
121
WS0_OUT
O
L/R sampling clock signal output to the digital audio interface receiver
122
SCK0
O
Bit clock signal output to the digital audio interface receiver
123
IOVCC33
-
Power supply terminal (+3.3V)
124
SD0_0
O
Digital audio signal output to the digital audio interface receiver
125
MCLK
O
Master clock signal output to the digital audio interface receiver
126 to 128
SD0_1 to SD0_3
O
Digital audio signal output to the digital audio interface receiver
Click on the first or last page to see other HT-ST3 service manuals if exist.