Sony HMZ-T3 / HMZ-T3W (serv.man2) Service Manual ▷ View online
HMZ-T3/T3W
1-13E
1-8-2. For HMZ-T3W
< Procedure >
1. Connect PU unit to AC through AC adaptor. (Fig.1)
2. Connect PU unit and PBU unit with HDMI cable. (Fig.1)
3. Connect JIG PC and PBU unit with Micro USB cable. (Fig.1)
4. Press
power button on PU and HMU,and the unit is powered on.
5. Press
MENU button on HMU, and setting menu is indicated.
6. Press
▲/▼ button on HMU, and select general setup.
7. Press
MENU button on HMU.
8. Press
▲/▼ button on HMU, and select wireless standby.
9. Press
MENU button on HMU.
10. Press
▲/▼ button on HMU, and select off.
11. Press
MENU button on HMU.
12. Press
◀ button on HMU, and finish setting menu.
13. Run HmzServiceTool.exe.
14. Click on “
Up Date” button. (Fig.2)
15. Make sure that “
1 HMD device(S)found.” is indicated on the Command Window screen. (Fig.2)
16. Click on “
Update Firmware” button (Fig.2), “HmdWriter” window will be displayed. (Fig.3)
17. Drag and drop a “
Target Firmware” in the “File Name” window. (Fig.3)
18. Make sure that the target firmware file name indicates on the “
File Name” window. (Fig.3)
19. Click on “
Start” button and the unit is powered on automatically.
*Click “
OK” button, if “PU connection Check Failed Continue? [OK] [Cancel] “pop up screen is indicated.
Do not perform power on the unit manually at this option.
20. Make sure that “
OK! Firmware update succeeded” popup window is displayed.
21. Click on “
OK” button on the popup window, the unit will shut down automatically.
22. Disconnect each cable.
Wireless
US
B
B
Battery
Jig PC
HDMI Out
Command
PBU
HMU
PU
HDMI/MHL
AC Adaptor
Fig.1
Fig.2
Fig.3
< Note >
1. Perform the upgrade to combined customer’s units without
any mixed unit, because HMZ-T3 series ensure scheduled
performance by upgrade only by couple of PU unit, PBU unit
and HMU unit.
2. LED Indication when upgrading.
PBU : Blinking green, PU : non-luminous
3. LED Indication when c
omplete the upgrade.
PBU : non-luminous, PU : Lighting RED
HMZ-T3/T3W
2-1
2-1. Processor Unit (HMZ-T3-P/T3W-P)
2-1-1. DISASSEMBLY FLOW
SECTION 2
DISASSEMBLY
・This set can be disassembled in the order shown below.
UNIT (HMZ-T3P)
2-1-2. CASE, SU
(Page 2-2)
(Page 2-2)
2-1-2. FL-2005 MOUNT
(Page 2-2)
(Page 2-2)
2-1-4. SU-1001 MOUNT
(Page 2-3)
2-1-2. HOLDER LED
ASSY, SU (Page 2-2)
ASSY, SU (Page 2-2)
2-1-4. BASE, SU
(Page 2-3)
(Page 2-3)
2-1-2. FL-2005 MOUNT
(Page 2-2)
(Page 2-2)
2-1-3. FAN HOLDER, SU
(Page 2-3)
(Page 2-3)
2-1-2. CASE, SU
(Page 2-2)
(Page 2-2)
2-1-2. HOLDER LED
ASSY, SU (Page 2-2)
ASSY, SU (Page 2-2)
2-1-3. WIRELESS HD
MODULE(Page 2-3)
2-1-5. BLOWER FAN
(UB5U3-509) (Page 2-4)
2-1-4. SU-1001 MOUNT
(Page 2-3)
2-1-4. BASE, SU
(Page 2-3)
(Page 2-3)
UNIT (HMZ-T3WP)
HMZ-T3/T3W
2-2
2-1-2. CASE, SU / HOLDER LED ASSY, SU / FL-2005 MOUNT
NOTE: Follow the disassembly procedure in the numerical order given. It is TORX screw, and some parts are fixed, and
TORX driver (T5) is necessary on the occasion of disassembly and installation.
TORX driver (T5) is necessary on the occasion of disassembly and installation.
①two screws (TORX 1.7X6)
② WIRE,LEAD WITH
CONNECTOR 13P80
(CN6501)
③ CASE, SU
④ one screw (P1.7X4 )
⑤ one hook
⑥ HOLDER LED
ASSY, SU
③ CASE, SU
⑧ WIRE,LEAD WITH
CONNECTOR(3P44)
(CN8001)
⑨FL-2005 MOUNT
④ one screw (P1.7X4 )
⑦ two screws (P1.7X4 )
HMZ-T3/T3W
2-3
2-1-4. SU-1001 MOUNT / BASE, SU
2-1-3. FAN HOLDER, SU / WIRELESS HD MODULE (HMZ-T3W only)
② harness
(CN6502)
③ FAN HOLDER, SU
① three screws (P3X5)
④ FPC
(CN1006)
⑥ WIRELESS HD
MODULE
⑤ two screws
(TORX 1.7X6)
① four screws
(P3X5)
① two screws (P3X5)
① one screw (P3X5)
T3 only
① one screw (BV3X7)
② one hook
⑥ BOTTOM, SU
④ one rib
⑤ BASE, SU
③ SU-1001 MOUNT
[Notes]
When change WIRELESS HD MODULE, reuse two pieces of
SHEET,RADIATION stuck on the parts surface.
When change WIRELESS HD MODULE, reuse two pieces of
SHEET,RADIATION stuck on the parts surface.
Click on the first or last page to see other HMZ-T3 / HMZ-T3W (serv.man2) service manuals if exist.