Sony HCD-ZX10 / MHC-ZX10 Service Manual ▷ View online
9
2-5. MAIN BOARD, FRONT AMP BOARD
2-6. CD BASE UNIT
(BU-K2BD38)
1
three screws
(BVTP 3
(BVTP 3
× 6)
3
two screws
(PTPWH M 2.6)
(PTPWH M 2.6)
5
two screws
(PTPWH M 2.6)
(PTPWH M 2.6)
4
spring (insulator),
compression
6
spring (insulator),
compression
7
CD base unit
(BU-K2BD38)
2
chassis
1
connector
(CN713)
7
connector
(CN913)
8
connector
(CN801)
5
two connectors
(CN803, CN804)
6
MAIN board
2
flat type wire (17core)
(CN522)
3
flat type wire (19core)
(CN523)
4
two screws
(BVTP 3
(BVTP 3
× 8)
9
two screws
(BVTP 3
(BVTP 3
× 16)
0
two screws
(BVTP 3
(BVTP 3
× 8)
qs
two screws
(BVTP 3
(BVTP 3
× 8)
qa
heat sink
qd
Remove the FRONT AMP board
in the arrow direction.
in the arrow direction.
10
2-7. CD MECHANISM DECK SECTION
(CDM53F-K2BD38)
2-8. FITTING BASE (GUIDE) ASSY, BRACKET (CHASSIS) AND
FITTING BASE (MAGNET) ASSY
1
three screws
(BVTT 3
(BVTT 3
× 6)
5
CD mechanism deck section
(CDM53F-K2BD38)
2
two screws
(BVTT 3
(BVTT 3
× 6)
4
four screws
(sumitite (B3), +BV)
(sumitite (B3), +BV)
3
chassis, sub
7
four screws
(BVTP M2.6)
(BVTP M2.6)
2
four screws
(BVTP M2.6)
(BVTP M2.6)
5
bracket
(chassis)
(chassis)
4
two screws
(BVTP M2.6)
(BVTP M2.6)
4
three screws
(BVTP M2.6)
(BVTP M2.6)
6
connector
(CN710)
(CN710)
1
two connectors
(CN709, 715)
(CN709, 715)
8
base (magnet) assy, fitting
3
base
(guide) assy, fitting
11
2-9. TRAY (SUB)
2-10. CHASSIS (MOLD B) SECTION, STOCKER SECTION AND
SLIDER (SELECTION)
pulley (LD)
stocker
section
section
tray (sub)
pulley (mode)
slider (selection)
1
Rotating the pulley (LD), shift the slider (selection) in the arrow A direction.
2
Rotating the pulley (mode) in the arrow direction, adjust the tray (sub) to be removed.
3
Rotating the pulley (LD), shift the slider (selection) in the arrow B direction.
4
Rotating the pulley (mode) in the arrow direction, remove the tray (sub) to be removed.
A
B
5
stocker
section
section
4
two step
screws
screws
4
two step screws
3
gear (eject)
2
chassis (mold B) section
Note: Rotating the pulley (LD),
shift the slider (selection)
to the left.
to the left.
9
compression
spring
spring
7
slider (selection)
8
washer
6
two screws
(PTPWH M2.6)
(PTPWH M2.6)
1
three screws
(BVTP M2.6)
(BVTP M2.6)
pulley (LD)
Note : In mounting the parts, refer to page 12 and 13.
12
2-11. GEARS INSTALLATION
2-12. SLIDER (SELECTION) INSTALLATION
portion A
2
gear (chuking)
6
two screws
(PTPWH M2.6)
(PTPWH M2.6)
5
washer
3
convex portion of
slider (selection)
slider (selection)
4
compression spring
7
Insert the slider (selection)
into the portion A.
into the portion A.
1
rotary encoder
rotary encoder
Align with the slot of
rotary encoder.
rotary encoder.
align marking
gear (chuking)
Insert a convex portion into
a groove of gear (chuking).
a groove of gear (chuking).
1
Slide the slider (U/D)
fully in the arrow
direction.
fully in the arrow
direction.
3
gear (gear B)
2
gear (U/D slider)
4
gear (gear A)
Adjust the gear (gear B) with the
portion A as shown.
portion A as shown.
Adjust the gear so that it meshes with
the bottom tooth of slider (U/D)gear,
as shown.
the bottom tooth of slider (U/D)gear,
as shown.
portion A
slider (U/D) gear
linearly
gear
(gear B)
(gear B)
Adjust so as to be aligned with
gear (B) linearly,as shown.
gear (B) linearly,as shown.
Click on the first or last page to see other HCD-ZX10 / MHC-ZX10 service manuals if exist.