DOWNLOAD Sony HCD-ZX10 / MHC-ZX10 Service Manual ↓ Size: 7.92 MB | Pages: 75 in PDF or view online for FREE

17

2. Correction of Errors
[When due to tape deck]
Stopped while tape aging operation with the “  ” displayed state.

[When due to CD]
Press  x ,  DISPLAY , and  Z  together to display the error code.

• Display of number of mechanism errors

Move the stick to the left and right to display “CDM Err Count *”.
* is the number of mechanism errors.

• Display of mechanism error

Move the stick to the left and right to display “CDM E**D##$$%%!!”.
Move the stick up and down to send the error number.

**

: Error number 00 is the latest error.

The larger the number, the older will the error be. (Maximum 9)

##

: FF is the mechanism error after mechanism initialization ends.

$$

: Judge from the first digit of the error number. (Don’t care the second digit.)

When the error number is 1 or 2, it indicates mechanism error in tray loading between the stocker position and behind it.

%% : Judge from the first digit of the error number. (Don’t care the second digit.)

When the error number is 2, it indicates mechanism error in the up/down movements of the stocker.

!!

: Judge from the first digit of the error number. (Don’t care the second digit.)

When the error number is 2, it indicates mechanism error during switching of the clamper and mode.

• No DISC error display

Move the stick left and right to display “No Disc Count *”.
* means the number of no discs.

• No DISC error display

Move the stick left and right to display “No E**D##$$%%00”.
Move the stick up and down to send the error number.

**

: Error number 01 is the latest error.

The larger the number, the older will the error be. (Maximum 3)

##

: 01 .... FOCUS ERROR

02 .... GFS ERROR
03 .... SET UP ERROR

$$

: 00 .... Judged as No DISC without attempting chucking retry

02 .... Judged as No DISC after chucking retry

%% : Judged with the first digit of the error number in the state where No DISC has been determined.

(Don’t care the second digit.)
1 ...... STOP
2 ...... SET UP
3 ...... TOC Read
4 ...... Access
5 ...... PLAY
6 ...... PAUSE
7 ...... Manual Search (during PLAY)
8 ...... Manual Search (during PAUSE)

3. Ending the Aging Mode
1) End the Aging Mode with the power off.
2) To reset the CD error history, be sure to perform cold reset.

18

3.04 – 6.96 N • m

(31 to 71 g • cm)

(0.43 – 0.98 oz • inch)

0.20 – 0.58 N • m

(2 to 6 g • cm)

(0.02 – 0.08 oz • inch)

3.04 – 6.96 N • m

(31 to 71 g • cm)

(0.43 – 0.98 oz • inch)

0.20 – 0.58 N • m

(2 to 6 g • cm)

(0.02 – 0.08 oz • inch)

6.97 – 14.02 N • m

(71 to 143 g • cm)

(0.98 – 1.99 oz • inch)

0.98 N • m or more

(100 g or more)

(3.53 oz or more)

0.98 N • m or more

(100 g or more)

(3.53 oz or more)

CQ-102C

CQ-102C

CQ-102RC

CQ-102RC

CQ-201B

CQ-403A

CQ-403R

Precaution
1. Clean the following parts with a denatured alcohol-moistened

swab:

record/playback heads

pinch rollers

erase head

rubber belts

capstan

idlers

2. Demagnetize the record/playback head with a head demagne-

tizer.

3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the

parts adjusted.

5. The adjustments should be performed with the rated power sup-

ply voltage unless otherwise noted.

Note: Perform this adjustments for both decks.

Procedure:
1. Mode : Playback

Signal

Used for

Tape

Mode

FWD

FWD
back tension

REV

REV
back tension

FF/REW

FWD tension

REV tension

Torque meter

Meter reading

1. Demagnetize the record/playback head with a head demagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the

parts adjusted.

4. The adjustments should be performed with the rated power sup-

ply voltage unless otherwise noted.

5. The adjustments should be performed in the order given in this

service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit adjust-
ment.)

6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwise

specified.

P-4-A100

WS-48B

P-4-L300

10 kHz, –10 dB

3 kHz, 0 dB

315 Hz, 0 dB

Azimuth Adjustment

Tape Speed Adjustment

Level Adjustment

2. Turn the adjustment screw and check output peaks. If the peaks

do not match for L-CH and R-CH, turn the adjustment screw so
that outputs match within 1 dB of peak.

main board
CN301
Pin 1 (R-ch)
Pin 3 (L-ch)

19

4. After the adjustments, apply suitable locking compound to the

parts adjusted.

Adjustment Location: Playback Head (Deck A)

Record/Playback/Erase Head (Deck B)

3. Mode: Playback

Note: Set the test mode using the following method and begin tape

speed adjustment.
In the test mode, the speed will switch to double speed or
normal speed each time the  HI-SPEED DUB  button is pressed.

Procedure:
With the power turned ON, press the  x  button,  DISPLAY  button,
and  DISC 3  button simultaneously.
(The “VOLUME” on the fluorescent display tube will blink while
in the test mode.)
To exit the test mode, press the  "/1  button.

1. Insert the WS-48B into deck B.
2. Press the  H  button of deck B.
3. Press the  HI-DUB  button and play the tape at double speed.
4. Adjust RV1001 of the LEAF SW board so that the reading of

the frequency counter becomes 6000 ± 180 Hz.

5. Press the  HI-DUB  button and play the tape at normal speed.
6. Adjust RV1002 of the LEAF SW board so that the reading of

the frequency counter becomes 3000 ± 90 Hz.

Adjustment Location: LEAF SW board

W.RMS (JIS) less than 0.3%
(test tape: WS-48B)

Procedure:
Mode: Playback

Deck A is RV311 (L-CH) and RV411 (R-CH), deck B is RV301
(L-CH) and RV401 (R-CH)
so that adjustment within the following adjustment level.

Adjustment level:
CN301 playback level: 301.5 to 338.3 mV (–8.2 to –7.2 dB)
level difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board

°

°

°

°

Pin 2 (GND)

main board
CN301
Pin 3 (L-ch)

Pin 1 (R-ch)

main board
CN301
Pin 1 (R-ch)
Pin 3 (L-ch)

20

INTRODUCTION
When set to the test mode performed in Tape Speed Adjust-
ment, when the tape is rewound after recording, the “REC memory
mode” which rewinds only the recorded portion and playback is
set.
This “REC memory mode” is convenient for performing this ad-
justment. During recording, the input signal FUNCTION will auto-
matically switch to VIDEO.
(After recording, press the  m  button without stopping will re-
turn to the position where recording was started.)

1. Press  FUNCTION  button to select VIDEO. (This step is not

necessary if the above test mode has already been set.)

2. Insert a tape into deck B, press the  REC PAUSE/START  button,

and then press the  H  button to start recording.

3. Mode: Record

5. Confirm playback the signal recorded in step 2 become adjust-

ment level as follows.
If these levels do not adjustment level, adjust the RV341 (L-CH)
and RV441 (R-CH) on the AUDIO board to repeat steps 3 and 4.

Adjustment level: The playback output of 10 kHz level difference

against 315 Hz reference should be ± 1.0 dB.

Adjustment Location: AUDIO board

INTRODUCTION
When set to the test mode performed in Tape Speed Adjust-
ment, when the tape is rewound after recording, the “REC memory
mode” which rewinds only the recorded portion and playback is
set.
This  “REC memory mode” is convenient for performing this
adjustment. During recording, the input signal FUNCTION will au-
tomatically switch to VIDEO.
(After recording, press the  m  button without stopping will re-
turn to the position where recording was started.)

1. Press  FUNCTION  button to select VIDEO. (This step is not

necessary if the above test mode has already been set.)

2. Insert a tape into deck B, press the  REC PAUSE/START  button,

and then press the  H  button to start recording.

3. Mode: Record

4. Mode: Playback

5. Confirm playback the signal recorded in step 2 become adjust-

ment level as follows.
If these levels do not adjustment level, adjust the RV301 (L-CH)
and RV351 (R-CH) on the MAIN board to repeat steps 3 and 4.

Adjustment level:
CN301 playback level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)

Adjustment Location: MAIN board

4. Mode: Playback

main board
CN301
Pin 1 (R-ch)
Pin 3 (L-ch)

Ω

Ω

main board
CN301
Pin 1 (R-ch)
Pin 3 (L-ch)