Sony HCD-SBT100 / HCD-SBT100B / HCD-SBT300W / HCD-SBT300WB Service Manual ▷ View online
HCD-SBT100/SBT100B/SBT300W/SBT300WB
17
2-12. CHASSIS (MAIN) BLOCK-1
OK
NG
8 flexible flat cable (9P)
(CN251)
(CN251)
8 flexible flat cable (9P)
(CN104)
(CN104)
2 flexible flat cable (5P)
(CN502)
(CN502)
CN507
7 connector
(CN304)
(CN304)
4 connector
(CN3002)
(CN3002)
5 connector
(CN905)
(CN905)
3 connector
(CN831)
(CN831)
coating clip
MAIN board
WireVHWWLQJ
Note 3: Wire must not be extends
from the edge of the chassis.
WireVHWWLQJ
lead pin
coating clip
MAIN
board
board
MAIN board
RELAY board
6 Remove the
wire from the
coating
clip.
1 Remove wires from
the lead pin.
–
5HDUYLHZ
–
Note 4: When you install the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
(SBT100B/SBT300WB)
(SBT100/SBT300W)
Note 5: When installing the flexible flat cable, ensure the colored line.
No slanting after insertion.
colored line
colored line
Inserting is straight to the interior.
Inserting is slant.
flexible flat cable
flexible flat cable
connector
connector
OK
NG
Note 1: CN3002 and CN507 are quantity of pins of the same.
Do not insert to the wrong connector absolutely.
There is a possibility that the unit may be damaged
if the wrong.
Note 2: Do not remove this connector (CN501)
at this point. It is necessary to process
electrostatic measures of optical pick-up.
(See page 18)
Note 6: RELAY board is deleted from the midway
of production and the coating clip is added.
1HZW\SHFRDWLQJFOLS
)RUPHUW\SHOHDGSLQ
Ver. 1.2
HCD-SBT100/SBT100B/SBT300W/SBT300WB
18
2-13. CHASSIS (MAIN) BLOCK-2
9 flexible flat cable (24P)
(CN501)
(CN501)
7 chuck cap
6 claw
6 claw
6 claw
0 chassis (main) block
OK
NG
2 screw
(BV3)
(BV3)
3 coating clip
3 coating
clip
clip
2 two screw
(BV3)
(BV3)
2 screw
(BV3)
(BV3)
2 screw
(BV3)
(BV3)
2 two screws
(BV3)
(BV3)
4 Remove the
chassis (main) block
in the direction
of an arrow.
5 Remove the chuck cap
in the direction
of an arrow.
1 Draw out
wires.
wires.
(SBT300W/
SBT300WB)
SBT300WB)
–
Rear view
–
Note 1:
Before disconnecting flexible flat cable (24P) (CN501), solder the short-land.
Note 3: When installing the flexible flat cable,
ensure the colored line.
No slanting after insertion.
Note 4: When installing
the chuck cap,
align the triangle
marks.
colored line
colored line
Inserting is straight to the interior.
Inserting is slant.
flexible flat cable
flexible flat cable
connector
connector
OK
NG
OK
NG
8 Solder the short-land.
Note 2:
When assembling the
chassis (main) block,
remove the solder of
short-land after connecting
flexible flat cable (24P)
(CN501).
Solder is removed cleanly.
Solder is not removed.
HCD-SBT100/SBT100B/SBT300W/SBT300WB
19
2-14. TUNER BOARD (HCD-SBT100/SBT300W)
2-15. MODULE (DAB TUNER) (DAB1), DAB BOARD (HCD-SBT100B/SBT300WB)
3 two screws
(BVTP3
(BVTP3
u 8)
ferrite core (FC5)
5 flexible flat cable (9P)
(CN101)
(CN101)
8 TUNER board
6 shield (lower)
7 sheet (tuner)
flexible flat cable (9P) (FFC3)
1 tape
(sub
(sub
material)
2 Peeled from the
adhesive
adhesive
(BT).
cushion (S)
:LUHVHWWLQJ
)OH[LEOHIODWFDEOH3))&VHWWLQJ
ferrite core (FC5)
tape
(sub material)
(sub material)
TUNER board
4 Remove the TUNER board block
in the direction of an arrow.
colored line
colored line
Inserting is straight to the interior.
Inserting is slant.
flexible flat cable
flexible flat cable
connector
connector
OK
NG
Note: When installing the flexible flat cable,
ensure the colored line.
No slanting after insertion.
1 two screws
(BVTP3
(BVTP3
u 8)
qs two screws
(BVTP3
(BVTP3
u 8)
4 screw
(BVTP3
(BVTP3
u 8)
qs screw
(BVTP3
(BVTP3
u 8)
8 gasket
conductor side
qa module
(DAB
(DAB
tuner)
(DAB1)
qd bracket DAB
qf DAB
board
board
B
B
6 connector
(CN4003)
(CN4003)
0 pin header 2P
(CN01)
(CN01)
5 connector
(CN4001)
(CN4001)
2 Remove the DAB board
block in the direction
of an arrow.
7 Remove the module
(DAB tuner) block
in the direction
of an arrow.
in the direction
of an arrow.
9 Remove the two solders.
3 flexible flat cable (9P) (CN4004)
Note
Note
1:
When installing the flexible flat cable (9P),
do not mistake the insertion direction.
Note 2: When installing the flexible flat cable,
ensure the colored line.
No slanting after insertion.
colored line
colored line
Inserting is straight to the interior.
Inserting is slant.
flexible flat cable
flexible flat cable
connector
connector
OK
NG
HCD-SBT100/SBT100B/SBT300W/SBT300WB
20
2-16. MAIN BOARD
2-17. POWER CORD (AC1)
4 screw
(BV3)
(BV3)
4 screw
(BV3)
(BV3)
3 radiation sheet
4 screw
(BV3)
(BV3)
7 MAIN board
MAIN board
ditch
4 five screws
(BV3)
(BV3)
1 two screws
(BVTP3
(BVTP3
u 8)
2 heatsink
(AMP)
6 tape
(sub
(sub
material)
tape
(sub material)
(sub material)
–
Top view
–
–
Bottom view
–
–
Rear view
–
7DSHVXEPDWHULDOVHWWLQJ
MAIN board
ditch
tape
(sub material)
(sub material)
5 Remove the MAIN board block
in the direction of an arrow.
70 to 75 mm
3 power cord
(AC1)
(AC1)
2 cord bush
(2104)
(2104)
power cord
claw
cord bush
(2104)
(2104)
&RUGEXVKVHWWLQJ
1 power cord connector
(CN901)
(CN901)
Insert is shallow
Insert is straight
to the interior.
to the interior.
Insert is incline
connector
connector
connector
connector
NG
OK
NG
connector
connector
Note: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
Note: When the complete MAIN board is replaced, refer to “CHECKING
METHOD OF NETWORK CONNECTION” on page 5.
Click on the first or last page to see other HCD-SBT100 / HCD-SBT100B / HCD-SBT300W / HCD-SBT300WB service manuals if exist.