Sony HCD-GZR5D / MHC-GZR5D Service Manual ▷ View online
HCD-GZR5D
21
3-13. OPTRICAL PICK-UP
3-14. BELT (DLM3A)
floating screw
(+PTPWHM 2.6)
(+PTPWHM 2.6)
floating screw
(+PTPWHM 2.6)
(+PTPWHM 2.6)
sheet (bottom)
two screws
(insulator)
(insulator)
two screws
(insulator)
(insulator)
insulator
RG optical pick-up
RH bracket (BU)
RB insulator
RT insulator
RE cord
insulator
two screws
(+BTP 2.6
(+BTP 2.6
× 8)
three screws
(+BTP 2.6
(+BTP 2.6
× 8)
two screws
cover
belt (DLM3A)
belt (DLM3A)
two screws
HCD-GZR5D
22
3-16. BELT (MAIN), BELT (R/F)
3-15. MECHANISM DECK
Open the cassette box.
four screws
(+BVTP 2.6
× 8)
mechanical deck
two screws
(+BVTP 3
× 6)
DECK board
bracket (DECK)
connector
(CN501)
(CN501)
belt (R/F)
belt (MAIN)
HCD-GZR5D
23
SECTION 4
TEST MODE
[COLD RESET]
• The cold reset clears all data including preset data stored in the
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
the set to the customer.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn on the system.
2. Press [DSGX] button, [DISC 1] button and [
?/1
] button
simultaneously.
3. The message “RESET” appears on the LCD display. Then,
the LCD display becomes blank for a while, and the system is
reset.
reset.
[PANEL TEST MODE]
•
•
This mode is used to check the LCD display, LEDs,
keys, VOLUME jog and OPERATION DIAL jog, model,
destination, software version and VACS level.
keys, VOLUME jog and OPERATION DIAL jog, model,
destination, software version and VACS level.
Procedure:
1. Press
1. Press
[
x] button, [DISPLAY] button and [X] button
simultaneously.
2. All LEDs and segments in LCD display are lighted up. All
LEDs are lighted up.
3. When you want to enter to the software version dispaly mode,
press [FUNCTION] button. The model information appears
on the fl uorescent indicator tube. “G0012B0108” is shown.
Press [FUNCTION] button again to view the information.
on the fl uorescent indicator tube. “G0012B0108” is shown.
Press [FUNCTION] button again to view the information.
4. Each time [DSGX] button is pressed, the display changes
from the destination information display.
5. To release from this mode, press [
x] button, [DISPLAY]
button and [
X] button simultaneously.
[DVD SHIP MODE]
•
•
This mode can run the DVD sled motor optionally. Use this
mode, for instance, when cleaning the optical pick-up.
mode, for instance, when cleaning the optical pick-up.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select DVD function.
3. Press two buttons of [
3. Press two buttons of [
N] and [
?/1
] simultaneously.
4. Set to the DVD ship mode. (chucking on)
5. After blink “STANDBY”, “LOCK” is displayed, disconnect
5. After blink “STANDBY”, “LOCK” is displayed, disconnect
the AC plug.
[DVD SHIP AND COLD RESET]
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select DVD function.
3. Press three buttons of [FUNCTION], [DISC 2] and [
3. Press three buttons of [FUNCTION], [DISC 2] and [
?/1
]
simultaneously.
4. After blink “STANDBY”, “RESET” is displayed, disconnect
4. After blink “STANDBY”, “RESET” is displayed, disconnect
the AC plug.
[DVD SLOT LOCK]
•
•
This mode is for the antitheft of DVD disc in shop. (not for
transport)
transport)
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select DVD function.
3. Insert a disc.
4. While pressing the [
3. Insert a disc.
4. While pressing the [
x
] button, press the [
Z
] button for more
5 seconds.
5. The message “LOCKED” is displayed and the disc slot is
locked. (Even if exiting from this mode, the disc slot is still
locked)
locked)
6. If press the [
Z
] button to eject the disc, the message
“LOCKED” is displayed and can not eject the disc.
7. To release this lock, while pressing the [
x
] button, press the
[
Z
] button for 5 seconds again.
8. The message “UNLOCKED” is displayed and the disc slot is
unlocked.
[DVD COLOR SYSTEM]
•
•
This mode let you change the color system of the video
output from PAL to NTSC or vice-versa. This mode is not
available for Latin American and Russian models.
output from PAL to NTSC or vice-versa. This mode is not
available for Latin American and Russian models.
Procedure:
1. Press
1. Press
[
?/1
] button to turn on the system.
2. Select
DVD
function.
3. Press
[
?/1
] button again to turn off the system.
4. After pressing the [DISPLAY] button, press [
X
] button
and [
?/1
] button simultaneously. The system will turn on
automatically.
The message “COLOR PAL” or “COLOR NTSC” appears on
the LCD display.
the LCD display.
HCD-GZR5D
24
[TUNER STEP CHANGE]
•
•
The step interval of AM channels can be toggled between 9
kHz and 10 kHz. This mode is not available for Saudi Arabia
and Russia models.
kHz and 10 kHz. This mode is not available for Saudi Arabia
and Russia models.
Procedure:
1. Press
1. Press
[
?/1
] button to turn on the system.
2. Press [FUNCTION] button repeatedly to select the “AM”.
3. Press
3. Press
[
?/1
] button to turn off the system.
4. After pressing the [DISPLAY] button, press [TUNING +
M
y
] button and [
?/1
] button simultaneously. The system will
turn on automatically. The message “AM 9K STEP” or “AM
10K STEP” appears on the LCD display and thus the channel
step is changed.
10K STEP” appears on the LCD display and thus the channel
step is changed.
[DVD SERVICE MODE]
•
•
This mode let you make diagnosis and adjustment easily by
using the remote commander and the TV. The instructions,
diagnostic results, etc. are given on the on-screen display.
using the remote commander and the TV. The instructions,
diagnostic results, etc. are given on the on-screen display.
• TEST DISC LIST
Be sure to use the DVD disc that matches the signal standards
of your region.
of your region.
• CD
YEDS-18 (Part No.: 3-702-101-01)
PATD-012 (Part No.: 4-225-203-01)
• DVD SL (Single Layer)
NTSC : HLX-503 (Part No.: J-6090-069-A)
HLX-504 (Part No.: J-6090-088-A)
PAL : HLX-506 (Part No.: J-6090-077-A)
• DVD DL (Dual Layer)
NTSC : HLX-501 (Part No.: J-6090-071-A)
HLX-505 (Part No.: J-6090-089-A)
PAL : HLX-507 (Part No.: J-6090-078-A)
• Procedure to enter to DVD Service Mode:
1. Press
1. Press
[
?/1
] button to turn on the system.
2. Select DVD function.
3. Press
3. Press
[
x
] button and [
Z
] button simultaneously and then turn
the [VOLUME] knob clockwise.
4. The message “SERVICE IN” appears on the LCD display and
the Top Menu of Remocon Diagnosis Menu appears on the
on-screen display on the TV. The model name, main unit’s
micom version information (IF-con) and DVD fi rmware
version information (Syscon) are displayed at the bottom of
the on-screen display.
on-screen display on the TV. The model name, main unit’s
micom version information (IF-con) and DVD fi rmware
version information (Syscon) are displayed at the bottom of
the on-screen display.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
Model Name
: ESLOD_
**
IF-con
: V
Syscon
: Ver.
er. 01.01 (0000)
1.310
5. To execute each function, press its number by using numeric
button on the remote commander.
6. To release from this mode, press [
?/1
] button to turn off the
system.
• Execute IOP Measurement
In order to execute IOP measurement, the following standard
procedures must be followed.
procedures must be followed.
1. From the Top Menu of Remocon Diagnosis Menu, select “2.
Drive Manual Operation” by pressing the [2] button on the
remote commander. The following screen appears on the on-
screen display.
remote commander. The following screen appears on the on-
screen display.
2. Select “3. Manual Adjustment” by pressing the [3] button on
the remote commander. The following screen appears on the
on-screen display.
on-screen display.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
0 P Change Value
RETURN Return to previous menu
3. Select “6. Iop:” by pressing [6] button on the remote
commander.
4. Wait until a hexadecimal number appears in the on-screen
display as below:
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop. ED:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop. ED:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
0 P Change Value
RETURN Return to previous menu
5. Convert data from hexadecimal to decimal by using
conversion table.
6. Please
fi nd the label on the rear of the BU (Base Unit).
The default IOP value is written in the label.
Drive Manual Operation
1. Servo Control
2. T rack/Layer Jump
3. Manual Adjustment
4. Mecha test Mode
5. MIRR time Adjust
0. Return to Top Menu
2. T rack/Layer Jump
3. Manual Adjustment
4. Mecha test Mode
5. MIRR time Adjust
0. Return to Top Menu
Click on the first or last page to see other HCD-GZR5D / MHC-GZR5D service manuals if exist.