Sony HCD-FR1K / HCD-FR8 / HCD-FR9 (serv.man2) Service Manual ▷ View online
9
HCD-FR1/FR8/FR9
1-14. MOTOR (STOCKER) ASSY (ROLLER)(M771)
1-15. MOTOR (STOCKER) ASSY (MODE)(M761)
1
belt (roller)
4
ROLLER MOTOR board
2
Remove two solders.
3
two screws
(BVTP2.6
×
8)
5
motor (stocker) assy
(roller) (M771)
(roller) (M771)
1
Remove five solders
of rotary encoder.
of rotary encoder.
2
Remove two solders
of motor (M761)
of motor (M761)
MODE MOTOR
board
board
3
two screws
(BVTP2.6
×
8)
4
MODE MOTOR board
5
belt (mode)
6
motor (stocker) assy
(mode) (M761)
(mode) (M761)
10
HCD-FR1/FR8/FR9
1-16. RUBBER ROLLER (SLIDER) ASSY
1-17. TIMING BELT (FRONT/REAR)
qg
sub chassis
qf
screw
(BVTP2.6
×
8)
8
step screw
qs
step screw
5
step screw
9
tension
spring
(slider 2)
spring
(slider 2)
6
tension spring
(base slider 5)
(base slider 5)
3
tension spring
(base slider 5)
(base slider 5)
1
step screw
0
rubber roller
(slider 4) assy
(slider 4) assy
7
rubber roller
(slider 1) assy
(slider 1) assy
4
rubber roller
(slider 5) assy
(slider 5) assy
2
rubber roller
(slider S) assy
(slider S) assy
qa
rubber roller
(slider 2) assy
(slider 2) assy
qd
rubber roller
(slider 1) assy
(slider 1) assy
a
a
b
b
c
c
3
slider (mode cam) assy
5
two gears
(center)
(center)
7
two gears (center)
8
timing belt (rear)
timing belt
(rear)
(rear)
When install three timing belts,
its pass under each claws.
its pass under each claws.
9
timing belt (rear)
4
gear
(timing)
(timing)
2
gear (mode cam)
: Note
: Note
6
timing belt
(front)
(front)
1
screw
(PTPWH2.6
×
8)
timing belt
(rear)
(rear)
timing belt (front)
two claws
two claws
two claws
two claws
Note: Refer to assembly (Section 4)
11
HCD-FR1/FR8/FR9
1
screw
(PTPWH2.6
(PTPWH2.6
×
8)
3
screw
(PTPWH2.6
(PTPWH2.6
×
8)
7
screw
(PTPWH2.6
(PTPWH2.6
×
8)
9
screw
(PTPWH2.6
(PTPWH2.6
×
8)
qa
screw
(PTPWH2.6
(PTPWH2.6
×
8)
qs
cam (gear)
: Note
: Note
5
screw
(PTPWH2.6
(PTPWH2.6
×
8)
2
pulley
(mode deceleration)
(mode deceleration)
4
gear
(mode 5)
(mode 5)
8
gear (mode 3)
0
gear
(mode 2)
:Note
(mode 2)
:Note
6
gear (mode 4)
Note: Refer to assembly (Section 2).
8
screw
(PTPWH2.6
(PTPWH2.6
×
8)
1
screw
(PTPWH2.6
(PTPWH2.6
×
8)
9
cam
(eject lock)
: Note
(eject lock)
: Note
qs
gear
(eject lock)
(eject lock)
qd
gear
(mode 1)
(mode 1)
qg
two claws
0
screw
(PTPWH2.6
(PTPWH2.6
×
8)
ql
screw
(BVTP2.6
(BVTP2.6
×
8)
3
screw
(BVTP2.6
(BVTP2.6
×
8)
7
shaft
(shutter)
(shutter)
6
compression spring
(shutter)
(shutter)
4
two screws
(BVTP2.6
(BVTP2.6
×
8)
5
base (shutter) block
2
lever shutter (A)
w;
SENSOR board
qf
screw
(PTPWH2.6
(PTPWH2.6
×
8)
qh
rotary encoder
(S701)
(S701)
qj
claw
qk
harness
qa
cam
(BU U/D)
(BU U/D)
Note: Refer to assembly (Section 2).
1-18. CAM (GEAR)
1-19. SENSOR BOARD
12
HCD-FR1/FR8/FR9
SECTION 2
ASSEMBLY
• This is can be assemble according to the following sequence.
2-1. HOW TO INSTALL THE CAM (EJECT LOCK)
2-2. HOW TO INSTALL THE CAM (GEAR)
mark
cam (BU U/D)
cam (eject lock)
– bottom view • front –
gear (eject lock)
1
Rotate the cam (BU U/D) fully in the direction of arrow.
2
Engage the gear (eject lock) and the gear of the cam (eject lock)
aligning the mark with the center of the gear (eject lock).
aligning the mark with the center of the gear (eject lock).
boss
cam (gear)
mark
cam (BU U/D)
– bottom view • front –
1
Check that the cam (BU U/D) can not be rotated in the direction of arrow.
2
Align the mark on the cam (gear) with the boss as shown in the figure
and install the cam (gear).
and install the cam (gear).
Click on the first or last page to see other HCD-FR1K / HCD-FR8 / HCD-FR9 (serv.man2) service manuals if exist.