DOWNLOAD Sony HBD-NF7220 Service Manual ↓ Size: 13.09 MB | Pages: 122 in PDF or view online for FREE

12. Log: Error Log (Output of each Log)
This screen displays the contents of each log.

Note: Do not refer to the displayed date.

Screen 1: Selects log
Operation:
[1]/[ ] 

Moves to the Error Log output screen

[RETURN]  Returns to the top menu of the service mode

Screen 2: Displays the Error Log
(Displayed characters/values in the following fi gure are example)
Operation:
[

<

] 

Returns to the previous page

[

,

] 

Moves to the next page

[RETURN] Returns to the screen (Screen 1) that selects the log 

type

[RED] 

Writes the log contents to an USB memory device

•  Viewing the log display
Error Log:
 

[174] 2010/01/01 00:00:08 [ErrCode:0902A4053002]

 

[Index number] [Date] [Time] [Error code]

About copying log to USB memory device:
Press the [RED] button in each log display screen with the USB 
memory device inserted into the unit.

Note: Please do not press the [RED] button immediately after USB mem-

ory is inserted. 

 

  Please do not pull out USB memory immediately after the [RED] 

button was pressed.

Error Log:
 When 

“getErrLogFile.trm 

fi  le” exists in the USB memory de-

vice, errlog.log fi  le is output.

 Select Log

 Error Log

Note: Not used for the servicing.

There is a possibility that this mode cannot be correctly executed. 
Never use this mode.

15. Network (Network Test Diagnosis Screen: Ifconfi g)
Network menu for the wired ethernet.

Screen 1: Ifconfi g Test
Operation:
[ ] Activate Ifconfi g (Display network setting)
[,] 

Select ping test

[RETURN] Returns to the top menu of the service mode

Screen 2: Ping Test
Operation:
[

<

] Select 

Ifconfi g test

[RETURN]  Returns to the top menu of the service mode
(The details of a Ping test are “16. Network (Network Test Diag-
nosis Screen: Ping)”)

Screen 3: Ifconfi g Test Active
Display Ifconfi g command results.
(Displayed characters/values in the following fi gure are example)
Operation:
[ ] Ifconfi g retry
[,] Select 

Ping Test

[RETURN]  Returns to the top menu of the service mode

 Network

 Network

 Network

16. Network (Network Test Diagnosis Screen: Ping)
Ping test for the wired ethernet.

Screen 1: Ping Test
Operation:
[

<

] Select 

Ifconfi g test

[

m

] 

Ping execution preparation

[RETURN]  Returns to the top menu of the service mode

When “Ping to :>” is reversed, the [ ] button is pressed and IP 
is inputted.
Operation:
[ ] 

Finish to input

[RETURN]  Finish to input
[

<

] 

Finish to input and Select Ifconfi g Test

[0] to [9] 

Input Character sting ‘0-9’

Screen 3: Ping Test Active
When [START] is reversed, the [ ] button is pressed and execute 
ping.
Operation:
[ ] 

Activate ping test

[

M

] 

The IP address of the ping point is set up

[RETURN]  Returns to the top menu of the service mode

 Network

 Network

17. System Information (System Information Display)
This screen displays system information.

Screen 1: Basic Information
Operation:
[

,

] 

Drive information (delta IOP of a drive is measured) 
and wireless device information displayed (go to 
Screen 2)

[RETURN]  Returns to the top menu of the service mode

Screen 2: Drive and Wireless Information Menu
Operation:
[

<

] 

Basic Information displayed (go to Screen 1)

[RETURN]  Returns to the top menu of the service mode

When delta IOP is measured, it becomes impossible to use the Ver-
sion Up function.

Contents List:
Main LSI name
Model
Destination
Sequence Number
MAC
IP
IF-con Block 

IF-con Block Version

IFCon ADSP Coeff  IFCon ADSP Coeff Version
Bootloader Bootloader 

Version

Host Main 

Host Main Version

MicroBE MicroBE 

Version

Host Sub 

Host Sub Version

Middleware Middleware 

Version

ADSP ADSP 

Version

ADSP Coeff 

ADSP Coeff Version

2nd DSP 

2nd DSP Version

ADSP ADSP 

Version

IF Model
IF Dest
WLAN module Serial
WLAN module hw Version
WLAN module MAC Address
Drive Firm Revision
CD DIOP 

Delta IOP

DVD DIOP 

Delta IOP

BD DIOP 

Delta IOP

CD LD TIME  LD Time
DVD LD TIME  LD Time
BD LD TIME  LD Time
Bluetooth Device Address

 System Information

 System Information

Note: Not used for the servicing.

19. Drive
This menu is used to operate the drive using drive-related diagnos-
tic and tools.

Screen 1: Selecting items under *Drive
Operation:
[

M

]/[

m

] 

Selects the category

[ ] 

Activate the selected category

[RETURN]  Returns to the top menu of the service mode
[1]  Drive OP data Write
[2]  Servo Parameter Check Menu
[3]  Servo Signal Check Menu
[4]  S-Curve Check Menu
[5]  Readability Check Menu
[6]  OP Position Check Menu
[7]  OP Check Menu
[8] Aging Test Menu
[9]  Spindle Control Check Menu
[10] FA Test Mode

Screen 2: To start OP data Write
(Displayed characters/values in the following fi gure are example)
Operation:
[ ] Starts

Screen 3: Show OP data Write result
(Displayed characters/values in the following fi gure are example)
Operation:
NG - USB is not fi nd
OK - OP data write

• Drive 

Test

For drive operating check. Service is only use Drive OP data write 
to rewrite OP data after change of new CPU.

 Drive
[1] Drive OP data Write 

 Drive OP data Write

 Drive OP data Write

J-6090-199-A

BLX-104

Single Layer

J-6090-200-A

BLX-204

Dual Layer

J-2501-307-A

CD (HLX-A1)

J-2501-305-A

HLX-513

Single Layer (NTSC)

J-2501-306-A

HLX-514

Dual Layer (NTSC)

J-6090-077-A

HLX-506

Single Layer (PAL)

J-6090-078-A

HLX-507

Dual Layer (PAL)

Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-

989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.

1. BLX-104
Procedure:
1. Select 

23.976Hz/1080P.

2.  Play “4.Motion picture”.
3.  Check whether player can play back or not.
4.  Check each outputs.

• HDMI
• Audio
• Speaker out

*  When 1080/24P monitor is nothing, 1080i (59.94Hz or 50Hz) 

can use instead of 1080/24P.

 

However this is temporary correspondence.

*  When the output of HDMI is 1080p/1080i/720p, the signal of 

composite is not output.

 

It is necessary to lower the output of HDMI to 480p or 576p or 
less.

2. BLX-204
Procedure:
1.  Select 1080i (59.94Hz or 50Hz).
2.  Play “4.Motion picture”.
3.  Check whether player can play back or not.
 

(Check the picture and sound output)

3. CD (HLX-A1)
Procedure:
Check whether player can play back or not.
(Check the sound output)

4.  HLX-513/514 (NTSC), HLX-506/507 (PAL)
Procedure:
1.  After displayed Main Menu, select “1. Video Signal”.
2.  Play “1.Color bar 100%”.
 

(Check the picture and sound output)

3.  Return to Menu.
4.  Play “Demonstration 4:3” or “Demonstration 16:9”.
 

(Check the picture and sound output)

1-2.  Playback operation confi rmation
Confi rm operation in each signal/output mode of test disc (BLX-
104/204) according to the content of the repair.

Note: “AV Sync.” doesn’t operate.

:

Procedure :
1.  Press the [

?/1

] button to turn the power on.

2.  Input the following signal from Signal Generator to FM an-

tenna input directly.

Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation 

: 75 kHz

Modulation 

: 1 kHz

ANT input 

: 35 dBu (EMF)

Note: Please use 75 ohm “coaxial cable” to connect SG and the set. You 

cannot use video cable for checking.

 

  Please use SG whose output impedance is 75 ohm. 

 
3.  Set to FM tuner function and scan the input FM signal with 

automatic scanning.

4. Confi rm that input Frequency of A, B and C detected and auto-

matic scanning stops.

 
The stop of automatic scanning means “The station signal is re-
ceived in good condition”.

2. Networking Confi rmation
Confi rm it according to the following procedure when you confi rm 
the connection of the network.

Note: Do not execute “Network Connection Diagnostics” of “Network 

Settings” of the home menu with only the router connected.

Procedure:
1.  Connect the router with the unit with LAN cable.
2.  Turn on the power of the unit and the router.
3.  Press the [HOME] button on the remote commander, and the 

home menu is displayed.

4. Select 

“Setup” 

 “Network Settings”, and press the [ ] but-

ton on the remote commander.

5.  Select “Internet Settings” and press the [ ] button on the re-

mote commander.

6.  Select “View Network Status” and press the [ ] button on the 

remote commander.

7. Confi rm IP address are displayed in “IP Address”, “Subnet 

Mask” and “Default Gateway”.

IP Address Setting:

XXXX

Internet Access:

XXXX

Physical Connection:

XXXX

IP Address:

XXX.XXX.XXX.XXX

DNS Settings:

XXXX

MAC Address:

XXX.XXX.XXX.XXX

Primary DNS:

XXX.XXX.XXX.XXX

Secondary DNS:

XXX.XXX.XXX.XXX

Subnet Mask:

XXX.XXX.XXX.XXX

Default Gateway:

XXX.XXX.XXX.XXX