Sony HBD-N590 / HBD-N790W / HBD-N890W / HBD-N990W / HBD-N995W / HBD-T79 Service Manual ▷ View online
HBD-N590/N790W/N890W/N990W/N995W/T79
9
ADVANCE PREPARATION WHEN CONFIRMING OP-
ERATION
In order to perform the operation checking, all the units contained
in this unit are needed.
ERATION
In order to perform the operation checking, all the units contained
in this unit are needed.
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, the electrical discharge is necessary for
the electric shock prevention.
Connect the resistor to both ends of respective capacitors.
When checking the board, the electrical discharge is necessary for
the electric shock prevention.
Connect the resistor to both ends of respective capacitors.
• Switching
regulator
C207,
C402
– SWITCHING REGULATOR (Component Side) –
C207
800
:/2 W
800
:/2 W
C402
C402
C207
CHECKING METHOD OF NETWORK OPERATION
(HBD-N590/N790W/N890W/N990W/T79 only)
It is necessary to check the network operation, when replacing the
MB-149 board or wireless LAN card (WLC1). Check the operation
of wireless and wired LAN, according to the following method.
(HBD-N590/N790W/N890W/N990W/T79 only)
It is necessary to check the network operation, when replacing the
MB-149 board or wireless LAN card (WLC1). Check the operation
of wireless and wired LAN, according to the following method.
1. Checking Method of Wireless LAN Operation
Check that access point is recognized surely.
Check that access point is recognized surely.
Necessary Equipment:
Wireless access point with router function (AP)
Wireless access point with router function (AP)
Procedure:
1. Press the [HOME] button on the remote commander to enter
1. Press the [HOME] button on the remote commander to enter
the home menu.
2. Press
the
[
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Setup”
“Network Settings”, and press the [ ]
button on the remote commander.
3. Select “Internet Settings”, and press the [
] button on the re-
mote commander.
4. Press the [
m]/[M] buttons on the remote commander to select
“Wireless Setup (built-in)”, and press the [
] button on the
remote commander.
5. The system starts searching for access points, and displays a
list of up available network name (SSID).
6. Check that access point (SSID) is displayed on the searching
result.
7. Press the [
?/1
] button to turn the power off.
Note: Refer to the instruction manual about details of the setting method.
2. Checking method of wired LAN operation
Check that access point is recognized surely.
Check that access point is recognized surely.
Procedure:
1. Connect the main unit to the router or the hub, etc. with the
1. Connect the main unit to the router or the hub, etc. with the
LAN cable.
2. Press the [HOME] button on the remote commander to enter
the home menu.
3. Press
the
[
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Setup”
“Network Settings”, and press the [ ]
button on the remote commander.
4. Select “Internet Settings”, and press the [
] button on the re-
mote commander.
5. Press the [
m]/[M] buttons on the remote commander to select
“Wired Setup”, and press the [
] button on the remote com-
mander.
6. Press the [
m]/[M] buttons on the remote commander to select
“Auto”, and press the [
] button on the remote commander.
7. Press the [
,] button on the remote commander.
8. Press the [
m]/[M] buttons on the remote commander to select
“Save & Connect”, and press the [
] button on the remote
commander.
9. When “Internet Settings is now complete.” appears, then press
the [
] button on the remote commander.
10. Press the [HOME] button on the remote commander to enter
the home menu.
11. Press the [
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Setup”
“Network Settings”, and press the [ ]
button on the remote commander.
12. Press the [
m]/[M] buttons on the remote commander to select
“Network Connection Diagnostics”, and press the [
] button
on the remote commander.
13. Press the [
<]/[,] buttons on the remote commander to
select “Start”, and press the [
] button on the remote com-
mander.
14. Confi rm that “Network connections are correct” is displayed.
15. Press the [
15. Press the [
?/1
] button to turn the power off.
Note: Refer to the instruction manual about details of the setting method.
Ver. 1.1
HBD-N590/N790W/N890W/N990W/N995W/T79
10
INSTALLATION METHOD OF THE WIRELESS SOUND
SYSTEM (HBD-N790W/N890W/N990W/N995W/T79 only)
Procedure:
1. Insert the wireless transceiver (EZW-RT50 (HBD-N790W/
SYSTEM (HBD-N790W/N890W/N990W/N995W/T79 only)
Procedure:
1. Insert the wireless transceiver (EZW-RT50 (HBD-N790W/
N890W/N990W/T79) or EZW-RT20 (HBD-N995W)) of the
attachment in the wireless transceiver slot in the back of the
main unit (HBD-N790W/N890W/N990W/N995W/T79) and
the surround amplifi er (TA-SA300WR).
attachment in the wireless transceiver slot in the back of the
main unit (HBD-N790W/N890W/N990W/N995W/T79) and
the surround amplifi er (TA-SA300WR).
Wireless
transceiver
(EZW-RT50 (HBD-N790W/
N890W/N990W/T79) or
EZW-RT20 (HBD-N995W))
transceiver
(EZW-RT50 (HBD-N790W/
N890W/N990W/T79) or
EZW-RT20 (HBD-N995W))
Wireless
transceiver
(EZW-RT50 (HBD-N790W/
N890W/N990W/T79) or
EZW-RT20 (HBD-N995W))
transceiver
(EZW-RT50 (HBD-N790W/
N890W/N990W/T79) or
EZW-RT20 (HBD-N995W))
EZW-
RT5
0
Rear panel of the main unit
(HBD-N790W/N890W/N990W/N995W/T79)
(HBD-N790W/N890W/N990W/N995W/T79)
Rear panel of the surround amplifier
(TA-SA300WR)
(TA-SA300WR)
2. Connect the AC power cord of the main unit (HBD-N790W/
N890W/N990W/N995W/T79).
3. Press the [
\/1
] button on the main unit (HBD-N790W/
N890W/N990W/N995W/T79).
4. Connect the AC power cord of the surround amplifi er (TA-
SA300WR).
5. When a wireless transceiving becomes effective, the [LINK/
STANDBY] indicator of surround amplifi er (TA-SA300WR)
lights to green.
lights to green.
Note: Refer to the operating instructions when the [LINK/STANDBY]
indicator of surround amplifi er (TA-SA300WR) doesn’t light.
LINK/STANDBY indicator
.+0-56#0&$;
Ver. 1.1
HBD-N590/N790W/N890W/N990W/N995W/T79
11
HOW TO EJECT THE DISC WHEN POWER SWITCH TURN OFF
NX_AMP BOARD SERVICE POSITION
The BD drive is taken out, and please rotate
the pulley in the direction of the arrow by
screwdriver etc. after detaching and take
out the disc.
the pulley in the direction of the arrow by
screwdriver etc. after detaching and take
out the disc.
disc
– BD drive bottom view –
insulating sheet
NX_AMP board
switching regulator (SWR1)
power cord
HBD-N590/N790W/N890W/N990W/N995W/T79
12
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
2-2. COVER (TOP) BLOCK
(Page
(Page
13)
SET
2-3. TOUCH
BOARD
(Page
14)
2-4. COVER (BOTTOM) BLOCK
(Page
(Page
15)
2-5. SHIELD (DRIVE)
(Page
(Page
16)
2-6. BD DRIVE (BSX-3)
(Page
(Page
16)
2-7. LED BOARD
(Page
(Page
17)
2-11. WS BOARD BLOCK
(EXCEPT
(EXCEPT
N590)
(Page
19)
2-12. SHIELD (PS) BLOCK
(Page
(Page
19)
2-20. OPTICAL PICK-UP
(KEM-480AAA)
(Page
(KEM-480AAA)
(Page
25)
2-19. BOTTOM COVER
(Page
(Page
24)
2-14. BRACKET (PS)
(Page
(Page
21)
2-15. POWER CORD (AC1)
(Page
(Page
21)
2-16. HEAT SINK (AMP)
(Page
(Page
22)
2-17. NX_AMP BOARD
(Page
(Page
22)
2-8. WIRELESS LAN CARD (WLC1)
(EXCEPT
(EXCEPT
N995W)
(Page
17)
2-9. CHASSIS (MIDDLE) BLOCK
(Page
(Page
18)
2-10. BRACKET (DRIVE)
(Page
(Page
18)
2-18. MB-149 BOARD
(Page
(Page
23)
2-21. HOW TO BEND WIRE (FLAT TYPE)
(Page
(Page
26)
2-13. SWITCHING REGULATOR
(SWR1)
(Page
(SWR1)
(Page
20)
Ver. 1.1
Click on the first or last page to see other HBD-N590 / HBD-N790W / HBD-N890W / HBD-N990W / HBD-N995W / HBD-T79 service manuals if exist.