Sony HBD-N590 / HBD-N790W / HBD-N890W / HBD-N990W / HBD-N995W / HBD-T79 Service Manual ▷ View online
HBD-N590/N790W/N890W/N990W/N995W/T79
25
2-20. OPTICAL PICK-UP (KEM-480AAA)
1 two float screws (S)
1 two float screws (S)
6 optical pick-up
(KEM-480AAA)
5 insulator
5 insulator
5 insulator
5 insulator
4 flexible flat cable (45P)
3 wire (flat type) (9 core)
– BD drive bottom view –
Note: When installing the wire (flat type),
ensure the coloured line.
No slanting after insertion.
wire (flat type)
coloured line
connector
2 Remove the optical pick-up block
in the direction of an arrow.
HBD-N590/N790W/N890W/N990W/N995W/T79
26
2-21. HOW TO BEND WIRE (FLAT TYPE)
IOH[LEOHIODWFDEOHOHQJWKPP5HI1R))&
IOH[LEOHIODWFDEOHFRUHOHQJWKPP5HI1R))&1:1:1:1:7
IOH[LEOHIODWFDEOHFRUHOHQJWKPP5HI1R))&1
ZLUHIODWW\SHFRUHOHQJWKPP5HI1R))&
ZLUHIODWW\SHFRUHOHQJWKPP5HI1R))&
ZLUHIODWW\SHFRUHOHQJWKPP5HI1R))&
ZLUHIODWW\SHFRUHOHQJWKPP5HI1R))&
ZLUHIODWW\SHFRUHOHQJWKPP5HI1R))&
optical pick-up
(KEM-480AAA)
MAIN board
(CN1101)
50 mm
120 mm
76 mm
4 mm
optical pick-up
(KEM-480AAA)
MAIN board
(CN1701)
MS-486 board
MAIN board
(CN1260)
MAIN board
(CN5902)
tuner
MAIN board
(CN5905)
The lower side
is contact side.
is contact side.
The lower side
is contact side.
is contact side.
: Mountain fold
: Valley fold
: Valley fold
115 mm
115 mm
The lower side
is contact side.
is contact side.
The lower side
is contact side.
is contact side.
The lower side
is contact side.
is contact side.
117 mm
30 mm
51 mm
72 mm
12 mm
12 mm
146 mm
NX_AMP board
(CN3504)
MAIN board
(CN5904)
MAIN board
(CN6304)
12 mm
12 mm
146 mm
NX_AMP board
(CN3505)
FL board
(CN903)
The lower side
is contact side.
is contact side.
The lower side
is contact side.
is contact side.
The lower side
is contact side.
is contact side.
The lower side
is contact side.
is contact side.
28 mm
9 mm
8 mm
5 mm
The upper side is
terminal side.
terminal side.
The upper side is
terminal side.
terminal side.
27 mm
31 mm
42 mm
The upper side is
terminal side.
terminal side.
The upper side is
terminal side.
terminal side.
MAIN board
(CN6303)
TOUCH board
(CN700)
8 mm 20 mm
58 mm
55 mm
35 mm
The lower side
is contact side.
is contact side.
The upper side is
terminal side.
terminal side.
The upper side is
terminal side.
terminal side.
Ver. 1.1
HBD-N590/N790W/N890W/N990W/N995W/T79
27
SECTION 3
TEST MODE
COLD RESET (MAIN UNIT)
The cold reset clears data except BD/DVD data stored in the RAM
to initial conditions. Execute this mode when returning the unit to
the customers.
Procedure:
1. Press the [
The cold reset clears data except BD/DVD data stored in the RAM
to initial conditions. Execute this mode when returning the unit to
the customers.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Touch the [
x
] and [VOL –] sensors simultaneously and hold
down (around 5 seconds).
3. The message “RESET” appears on fl uorescent indicator tube,
then becomes standby states.
COLD RESET (SURROUND AMPLIFIER)
(HBD-N790W/N890W/N990W/N995W/T79 only)
Execute this mode when returning the unit to the customers.
(HBD-N790W/N890W/N990W/N995W/T79 only)
Execute this mode when returning the unit to the customers.
Note 1: The main unit corresponding to TA-SA300WR, wireless trans-
ceivers (EZW-RT50 (HBD-N790W/N890W/N990W/T79) or
EZW-RT20 (HBD-N995W)) (2 units) and the remote command-
er corresponding to the main unit are necessary to execute this
mode.
EZW-RT20 (HBD-N995W)) (2 units) and the remote command-
er corresponding to the main unit are necessary to execute this
mode.
Procedure:
1. Insert the wireless transceiver (EZW-RT50 (HBD-N790W/
1. Insert the wireless transceiver (EZW-RT50 (HBD-N790W/
N890W/N990W/T79) or EZW-RT20 (HBD-N995W)) of the
attachment in the wireless transceiver slot in the back of the
main unit (HBD-N790W/N890W/N990W/N995W/T79) and
the surround amplifi er (TA-SA300WR).
attachment in the wireless transceiver slot in the back of the
main unit (HBD-N790W/N890W/N990W/N995W/T79) and
the surround amplifi er (TA-SA300WR).
Wireless
transceiver
(EZW-RT50 (HBD-N790W/
N890W/N990W/T79) or
EZW-RT20 (HBD-N995W))
transceiver
(EZW-RT50 (HBD-N790W/
N890W/N990W/T79) or
EZW-RT20 (HBD-N995W))
Wireless
transceiver
(EZW-RT50 (HBD-N790W/
N890W/N990W/T79) or
EZW-RT20 (HBD-N995W))
transceiver
(EZW-RT50 (HBD-N790W/
N890W/N990W/T79) or
EZW-RT20 (HBD-N995W))
EZW
-RT50
Rear panel of the main unit
(HBD-N790W/N890W/N990W/N995W/T79)
(HBD-N790W/N890W/N990W/N995W/T79)
Rear panel of the surround amplifier
(TA-SA300WR)
(TA-SA300WR)
2. Connect the AC power cord of the main unit (HBD-N790W/
N890W/N990W/N995W/T79).
3. Press the [
\/1
] button on the main unit (HBD-N790W/
N890W/N990W/N995W/T79).
4. Connect the AC power cord of the surround amplifi er (TA-
SA300WR).
5. When a wireless transceiving becomes effective, the [LINK/
STANDBY] indicator of surround amplifi er (TA-SA300WR)
lights to green.
lights to green.
Note
2: Refer to the operating instructions when the [LINK/STAND-
BY] indicator of surround amplifi er (TA-SA300WR) doesn’t
light.
light.
LINK/STANDBY indicator
.+0-56#0&$;
6. Press the button in order of the [DISPLAY]
[0] [7] [2]
[SUBTITLE] on the remote commander corresponding to
main unit aiming at the main unit.
main unit aiming at the main unit.
7. Confi rm the [LINK/STANDBY] indicator of TA-SA300WR is
orange lighting after step 3 is executed.
8. The AC plug of TA-SA300WR is pulled out to turn off the
system.
Note
3: Please insert it after confi rming the [LINK/STANDBY] indi-
cator of TA-SA300WR has been turned off when you insert
the AC plug again.
the AC plug again.
DEMO MODE
This mode let you lock the disc slot. When this mode is activated,
the disc will not eject when the [
This mode let you lock the disc slot. When this mode is activated,
the disc will not eject when the [
Z
] sensor is touched. The mes-
sage “DEMO LOCK” will be displayed on the fluorescent indica-
tor tube.
Procedure:
1. Press the [
tor tube.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Insert a disc.
3. Press the [HOME] button on the remote commander to enter
3. Press the [HOME] button on the remote commander to enter
the home menu.
4. Touch the [
x
] and [
Z
] sensors simultaneously and hold down
until “DEMO.LOCK” or “DEMO OFF” displayed on the fluo-
rescent indicator tube (around 5 seconds).
rescent indicator tube (around 5 seconds).
Releasing method:
Touch the [
Touch the [
x
] and [
Z
] sensors simultaneously and hold down until
“DEMO OFF” displayed on the fl uorescent indicator tube (arround
5 seconds).
5 seconds).
Ver. 1.1
HBD-N590/N790W/N890W/N990W/N995W/T79
28
FACTORY INITIALIZE
Return all of the unit setting to their factory defaults.
Return all of the unit setting to their factory defaults.
Note 1: Disconnect the following connections when you use this mode.
Front USB
Rear USB
LAN
HDMI IN 1
HDMI IN 2
Note 2: The operation in this mode must use a remote commander and TV
monitor.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the [HOME] button on the remote commander, and the
home menu is displayed.
3. Select
“Setup”
“Resetting”, and press the [ ] button on the
remote commander.
Resetting
Easy Setup
4. Select “Initialize Personal Information”, and press the [
]
button on the remote commander.
Initialize Personal Information
Erase personal data when disposing
Erase personal data when disposing
Reset to Factory Default Settings
5. Select “OK”, and press the [
] button on the remote com-
mander.
Initialize Personal Information
OK
Cancel
The information below will be deleted.
Do you want to proceed?
- Playback history
- Internet video utilization information
Do you want to proceed?
- Playback history
- Internet video utilization information
PANEL TEST
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press button in order of the [DISPLAY]
[0] [0] [1]
[SUBTITLE] on the remote commander (Make the interval
when each button is pressed within two seconds).
when each button is pressed within two seconds).
3. All segments in fl uorescent indicator tube are lighted up. And
half segments in fl uorescent indicator tube are lighted up, oth-
ers half segments in fl uorescent indicator tube are lighted up,
then all segments in fl uorescent indicator tube are lighted up.
This operation is repeated.
ers half segments in fl uorescent indicator tube are lighted up,
then all segments in fl uorescent indicator tube are lighted up.
This operation is repeated.
4. When all segments in fl uorescent indicator tube are lighted up
in the state of step 3, press the [VOL +] button on the remote
commander and model information is displayed on the fl uores-
cent indicator tube.
commander and model information is displayed on the fl uores-
cent indicator tube.
Each time the [VOL +] button on the remote commander is
pressed, the display changes from destination information,
STR version in this order, and returns to the model informa-
tion display.
pressed, the display changes from destination information,
STR version in this order, and returns to the model informa-
tion display.
Each time the [VOL –] button on the remote commander is
pressed, the version and date are switched.
pressed, the version and date are switched.
5. In the state of step 3, press the [FUNCTION] button on the
remote commander and “K 0” is displayed on the fluorescent
indicator tube.
indicator tube.
“K 0” value increases whenever a button or sensor on the unit
is pressed. However, once a button or sensor has been pressed,
it is no longed taken into account.
is pressed. However, once a button or sensor has been pressed,
it is no longed taken into account.
All button and sensors on the unit are pressed, “OK” and “K 7”
are alternately displayed on the fluorescent indicator tube.
are alternately displayed on the fluorescent indicator tube.
6. In the state of step 3, press the [VOL –] button on the remote
commander and “RM” is displayed on the fluorescent indica-
tor tube.
tor tube.
Confirm that “L RM R” is displayed on the fluorescent in-
dicator tube, while pressing the [VOL –] button on the remote
commander.
dicator tube, while pressing the [VOL –] button on the remote
commander.
The remote control receiver (IC903 on the FL board and IC951
on the SIRCS board) may be defective when “L” and “R” are
not displayed.
on the SIRCS board) may be defective when “L” and “R” are
not displayed.
Releasing method:
To release from this mode, press the [
To release from this mode, press the [
?/1
] button.
DISC SLOT LOCK MODE
The EJECT operation by main unit, remote commander, and CEC
(path-through) can be prohibited.
Procedure:
1. Press the [\/1] button to turn the power on.
2. Insert a disc.
3. Press button in order of the [DISPLAY]
The EJECT operation by main unit, remote commander, and CEC
(path-through) can be prohibited.
Procedure:
1. Press the [\/1] button to turn the power on.
2. Insert a disc.
3. Press button in order of the [DISPLAY]
[0] [0] [4]
[SUBTITLE] on the remote commander.
(Make the interval when each button is pressed within two sec-
onds)
onds)
4. “TLK ON” is displayed on the fl uorescent indicator tube, and
the EJECT operation by main unit, remote commander, and
CEC (path-through) is prohibited.
CEC (path-through) is prohibited.
Releasing method:
1. Press button in order of the [DISPLAY]
1. Press button in order of the [DISPLAY]
[0] [0] [4]
[SUBTITLE] on the remote commander.
(Make the interval when each button is pressed within two sec-
onds)
onds)
2. “TLK OFF” is displayed on the fl uorescent indicator tube, and
the EJECT operation by main unit, remote commander, and
CEC (path-through) become effective.
CEC (path-through) become effective.
Click on the first or last page to see other HBD-N590 / HBD-N790W / HBD-N890W / HBD-N990W / HBD-N995W / HBD-T79 service manuals if exist.