Sony HBD-N590 / HBD-N790W / HBD-N890W / HBD-N990W / HBD-N995W / HBD-T79 Service Manual ▷ View online
HBD-N590/N790W/N890W/N990W/N995W/T79
13
Note: Follow the disassembly procedure in the numerical order given.
2-2. COVER (TOP) BLOCK
1 two screws
(BV DIA. 2.6
u 8)
1 five screws
(BV DIA. 2.6
u 8)
1 five screws
(BV DIA. 2.6
u 8)
4 eight claws
5 wire (flat type) (11 core)
(CN700)
wire (flat type)
2 three claws
3 Remove the cover (top) block
in the direction of an arrow.
6 cover (top) block
2 four claws
Note 3: Align this portion into the groove
and align screw boss beneath the
screw
hole.
Note 2: Since the wire (flat type) (11core) is
connected, remove slowly.
screw hole
screw boss
groove
– Rear bottom view –
– Rear top view –
– Rear view –
Note 3: Align this portion into the groove
and align screw boss beneath the
screw
hole.
screw hole
screw boss
groove
– Rear view –
Note 4: When installing the wire (flat type),
ensure the coloured line.
No slanting after insertion.
coloured line
connector
Note 1: Please spread a sheet under a unit
not to injure cover (top).
HBD-N590/N790W/N890W/N990W/N995W/T79
14
2-3. TOUCH BOARD
1 connector
(CN701)
2 three claws
3 reflector (touch) assy
– Bottom view –
reflector (touch) assy
TOUCH board
PWR_KEY board
:iUe VettiQJ
4 TOUCH board
Note 3: Since it is pasted by adhesion
sheet, remove carefully.
Note 2: Please spread a sheet under a unit
not to injure cover (top).
Note 1: When TOUCH board is defective, exchange
the complete mounted board.
HBD-N590/N790W/N890W/N990W/N995W/T79
15
2-4. COVER (BOTTOM) BLOCK
1 two screws
(BV DIA. 2.6
u 8)
1 three screws
(BV DIA. 2.6
u 8)
1 three screws
(BV DIA. 2.6
u 8)
– Rear bottom view –
– Rear top view –
– Rear top view –
3 Remove the chassis (main) block
in the direction of an arrow.
1 Slant to fit the cord bushing underneath
the claw of cover (bottom) block.
2 Align two holes to two bosses and rest
down at cover (bottom) block.
two bosses
two holes
cord bushing
cover (bottom) block
4 chassis (main) block
5 cover (bottom) block
2 Open the lid
(USB-side).
2 Open the lid
(USB-front).
(N590/N790W/
N890W/T79)
N890W/T79)
(N990W/N995W)
+RZWRLQVWDOOWKHFRYHUERWWRPEORFN
Ver. 1.1
HBD-N590/N790W/N890W/N990W/N995W/T79
16
2-5. SHIELD
(DRIVE)
2 shield (drive)
1 two screws
(BV3)
1 two screws
(BV3)
2-6. BD DRIVE (BSX-3)
3 wire (flat type) (45P)
(CN1101)
5 wire (flat type)
(7 core) (CN1701)
4 wire (flat type)
(9 core) (CN1260)
1 two screws
(BV3)
1 two screws
(BV3)
6 three screws
(BV3)
7 bracket (slot)
8 sound sheet
9 BD drive (BSX-3)
2 Remove the BD drive block
in the direction of an arrow.
Note: When installing the wire (flat type),
ensure the coloured line.
No slanting after insertion.
wire (flat type)
coloured line
connector
Click on the first or last page to see other HBD-N590 / HBD-N790W / HBD-N890W / HBD-N990W / HBD-N995W / HBD-T79 service manuals if exist.