Sony DHC-FL5D / HCD-FL5D Service Manual ▷ View online
5
HCD-FL5D
9-16. Tape Mechanism Deck Section-2
(TCM-230PWR41CS: TH Model) ................................ 129
9-17. Tape Mechanism Deck Section-3
(TCM-230PWR41CS: TH Model) ................................ 130
10. ELECTRICAL PARTS LIST
.............................. 131
6
HCD-FL5D
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveforms is output three times.
check that the S curve waveforms is output three times.
SERVICE POSITION
In checking the DSP/MB/MC/VIDEO boards, prepare jig.
SECTION 1
SERVICING NOTES
• MODEL IDENTIFICATION
– Back Panel –
– Back Panel –
MODEL
PART No.
Singapore model
4-240-281-0
[]
Saudi Arabia model
4-240-281-1
[]
Australian model
4-240-281-2
[]
Mexican model
4-240-281-3
[]
Thailand model
4-240-281-4
[]
PART No.
extension cable (J-2501-217-A)
to the MB board (CN501)
and RF board (CN002)
to the MB board (CN501)
and RF board (CN002)
extension cable (J-2501-198-A)
to the MB board (CN204)
and video board (CN701)
to the MB board (CN204)
and video board (CN701)
video board (CN701)
GC board
regulator board
SP relay board
DSP board
front rear AMP board
blue LED board
panel (L) board
panel (R) board
RF board (CN002)
mechanism deck
MB board (CN204)
SUB trans board
trans board
center SW AMP board
MB board (CN501)
Any board to put
MC board
7
HCD-FL5D
• TYPE A/B DISCRIMINATION
Specification of this set is changed in the midway of production.
Therefore, the set is classified into two types according to which
IC, IC204 or IC205, is mounted.
When replacing IC205 of type A, install IC204 instead of IC205.
Therefore, the set is classified into two types according to which
IC, IC204 or IC205, is mounted.
When replacing IC205 of type A, install IC204 instead of IC205.
– MB BOARD (Conductor Side) –
IC205 (48 pin) is mounted : TYPE A
IC204 (44 pin) is mounted : TYPE B
• RELEASING THE DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
disc in the store is equipped.
Releasing Procedure :
Press two buttons of
Press two buttons of
Z
(DVD) and
[DVD TOP MENU]
simulta-
neously for five seconds. The message “UNLOCKED” is displayed
and the tray is unlocked.
and the tray is unlocked.
Note:
When “LOCKED” is displayed, the tray lock is not released by
turning power on/off with the
turning power on/off with the
[I/ ]
button.
1
Ver 1.5
NOTE OF REPLACING THE MB BOARD
When replacing the MB board, since the adjustment value is not
set up correctly, “Drive Auto Adjustment” can’t be performed.
In this case, initialize Memory in the following procedures.
set up correctly, “Drive Auto Adjustment” can’t be performed.
In this case, initialize Memory in the following procedures.
Procedure:
1. Set the test mode. (See page 27)
2. Press the
1. Set the test mode. (See page 27)
2. Press the
[2]
key of the remote commander, and set the “DRIVE
MANUAL OPERATION”. (See page 29)
3. Press the
[6]
key of the remote commander, and set the “2-6,
Memory Check”. (See page 31)
4. Press the
[CLEAR]
key of the remote commander, and initial-
ize Memory.
8
HCD-FL5D
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
LOCATION OF CONTROLS
– Front Panel –
– Front Panel –
– Rear Panel –
ALPHABETICAL ORDER
A – D
CD SYNC HI-DUB qd
DIGITAL wf
DISC SELECT 4
DISC 1 indicator wl
DISC 2 indicator wk
DISC 3 indicator wj
DISC 4 indicator wh
DISC 5 indicator wg
Display window 2
DISPLAY ws
DVD ed
DVD MENU qs
DVD TOP MENU qa
DIGITAL wf
DISC SELECT 4
DISC 1 indicator wl
DISC 2 indicator wk
DISC 3 indicator wj
DISC 4 indicator wh
DISC 5 indicator wg
Display window 2
DISPLAY ws
DVD ed
DVD MENU qs
DVD TOP MENU qa
E – R
ECHO LEVEL (Asian model
only) wa
MD (VIDEO) wd
MIC jack ql
MIC LEVEL w;
MULTI CHANNEL DECODING
MIC jack ql
MIC LEVEL w;
MULTI CHANNEL DECODING
indicator 3
PHONES jack qh
REC PAUSE/START qf
Remote sensor e;
REC PAUSE/START qf
Remote sensor e;
BUTTON DESCRIPTIONS
?/1 (power) 1
Z (disc tray) 5
Z A (deck A) qk
Z B (deck B) qj
hH (play) 6
X (pause) 8
x (stop) 7
./> (go back/go forward)
Z (disc tray) 5
Z A (deck A) qk
Z B (deck B) qj
hH (play) 6
X (pause) 8
x (stop) 7
./> (go back/go forward)
9
–/m, M/+
(rewind, fast forward) q;
Z
Z
Z
x
X
>
.
M
+
–
m
hH
?/1
1
6
8
45
2
3
ed
es
ea
wf
wd
ws
qk
qa
qs
qd
qf
qg
qh
qj
7
9
q;
wl
wk
wj
wh
wg
w;
ql
wa
e;
T – V
TAPE A/B ea
TUNER/BAND es
VOLUME qg
TUNER/BAND es
VOLUME qg
A
COMPONENT VIDEO OUT jacks
Use video cables (not supplied) to connect an
optional component (such as a TV) to this jack.
If your TV accept progressive format file
signals, you must use this connection and set
“COMPONENT OUT” to “PROGRESSIVE”
in “SCREEN SETUP”.
optional component (such as a TV) to this jack.
If your TV accept progressive format file
signals, you must use this connection and set
“COMPONENT OUT” to “PROGRESSIVE”
in “SCREEN SETUP”.
B
VIDEO OUT jack
Use a video cable (supplied) to connect an
optional component (such as a TV) to this jack.
You can then output the video to the
component from this unit, and enjoy the video
images of DVDs, etc.
optional component (such as a TV) to this jack.
You can then output the video to the
component from this unit, and enjoy the video
images of DVDs, etc.
C
S VIDEO OUT jack
Use an S video cable (not supplied) to connect
an optional component (such as a TV) to this
jack. You can then output the video to the
component from this unit, and enjoy higher
quality video images.
an optional component (such as a TV) to this
jack. You can then output the video to the
component from this unit, and enjoy higher
quality video images.
D
OPTICAL DIGITAL IN jack
Use a digital optical cable (square, not
supplied) to connect an MD deck or DVD
player to this jack. You can then record or
listen to digital audio from the MD deck or
DVD player through this system.
supplied) to connect an MD deck or DVD
player to this jack. You can then record or
listen to digital audio from the MD deck or
DVD player through this system.
E
OPTICAL DVD DIGITAL OUT jack
Use a digital optical cable (square, not
supplied) to connect an MD deck to this jack.
You can then output the digital audio to the
MD deck from this system.
supplied) to connect an MD deck to this jack.
You can then output the digital audio to the
MD deck from this system.
F
MD (VIDEO) IN jacks
Use audio cords (not supplied) to connect an
MD deck or VCR to these jacks. You can then
listen to analog audio from the MD deck or
VCR through this system.
MD deck or VCR to these jacks. You can then
listen to analog audio from the MD deck or
VCR through this system.
G
MD (VIDEO) OUT jacks
Use audio cords (not supplied) to connect an
MD deck or VCR to these jacks. You can then
output audio to the MD deck or VCR from this
system.
MD deck or VCR to these jacks. You can then
output audio to the MD deck or VCR from this
system.
Tip
When you remove the optical cover, keep it for future
use.
use.
Click on the first or last page to see other DHC-FL5D / HCD-FL5D service manuals if exist.