Sony DHC-FL5D / HCD-FL5D Service Manual ▷ View online
33
HCD-FL5D
• Error code (aa)
FF : Complete the initializing. (normal operation)
11 : Stocker movement (to chucking position) failing in the midst
11 : Stocker movement (to chucking position) failing in the midst
of initializing the mechanism deck.
12 : Stocker movement (to chucking position) failing in the midst
of initializing the mechanism deck.
1x : Initializing the mechanism deck.
2x : Initializing the mechanism deck.
3x : Initializing the mechanism deck.
41 : Disc eject failing in the midst of initializing the mechanism
2x : Initializing the mechanism deck.
3x : Initializing the mechanism deck.
41 : Disc eject failing in the midst of initializing the mechanism
deck.
4x : Initializing the mechanism deck.
50 : Disc eject failing in the midst of initializing the mechanism
50 : Disc eject failing in the midst of initializing the mechanism
deck.
5x : Initializing the mechanism deck.
A2 : Disc eject failing in the midst of initializing the mechanism
A2 : Disc eject failing in the midst of initializing the mechanism
deck.
Ax : Initializing the mechanism deck.
D3 : Disc eject failing in the midst of initializing the mechanism
D3 : Disc eject failing in the midst of initializing the mechanism
deck.
Dx : Initializing the mechanism deck.
Ex : Initializing the mechanism deck.
Ex : Initializing the mechanism deck.
•
Error code (bb)
00 : Initializing the mechanism deck.
10 : Retry over of eject and loading.
30 : Open operation in no disc status.
60 : Retry over of eject and loading.
70 : Disc is chucking position.
81 : Retry failed of disc movement from chucking position to
10 : Retry over of eject and loading.
30 : Open operation in no disc status.
60 : Retry over of eject and loading.
70 : Disc is chucking position.
81 : Retry failed of disc movement from chucking position to
stocker.
83 : Retry preparation failed of disc movement from chucking po-
sition to stocker.
90 : Disc is stored in the stocker.
A1 : Retry failed of disc movement from stocker to chucking po-
A1 : Retry failed of disc movement from stocker to chucking po-
sition.
A3 : Retry preparation failed of disc movement from stocker to
chucking position.
B0 : Just before the release operation.
B1 : Retry failed of the release operation.
B1 : Retry failed of the release operation.
• Error code (cc)
10 : Under a stop.
22 : Retry preparation failed.
23 : Retry failed.
22 : Retry preparation failed.
23 : Retry failed.
• Error code (dd)
10 : Under a stop.
22 : Retry preparation failed.
23 : Retry failed.
22 : Retry preparation failed.
23 : Retry failed.
6. VERSION INFORMATION
On the Test Mode Menu screen, selecting
[6]
displays the ROM
version and region code.
The parenthesized hexadecimal number in version field is
checksum value of ROM.
The parenthesized hexadecimal number in version field is
checksum value of ROM.
## Version Information ##
IF con.
Ver.x. xxx
SYScon.
Ver.x. xx (xxxx)
Model
DHC-FLxx
Region
0x
Config
xxxxxxxx
Front End Ver.x.xx
Exit: RETURN
IF con.
: The version of system controller (IC101).
SYScon. : The version of DVD system processor (IC206).
Front End: The version of mechanism controller (IC901).
Front End: The version of mechanism controller (IC901).
7. VIDEO LEVEL ADJUSTMENT
On the Test Mode Menu screen, selecting
[7]
displays color bars
for video level adjustment. During display of color bars, OSD dis-
appears but the menu screen will be restored if pressing the
appears but the menu screen will be restored if pressing the
[RE-
TURN]
key.
34
HCD-FL5D
Note:
Perform this adjustments for both decks
Procedure:
1. Mode: Playback
1. Mode: Playback
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw so
that outputs match within 1dB of peak.
that outputs match within 1dB of peak.
Screw
position
position
L-CH
peak
peak
within
1dB
1dB
Output
level
level
L-CH
peak
peak
R-CH
peak
peak
within
1dB
1dB
Screw
position
position
R-CH
peak
peak
SECTION 6
MECHANICAL ADJUSTMENTS
SECTION 7
ELECTRICAL ADJUSTMENTS
0 dB=0.775 V
DECK SECTION
1. Demagnetize the record/playback head with a head
demagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
3. After the adjustments, apply suitable locking compound to the
parts adjust.
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in this
service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit
adjustment.)
should be completed before performing recording circuit
adjustment.)
6. The adjustments should be performed for both L-CH and R-
CH.
7. Switches and controls should be set as follows unless otherwise
specified.
• Test Tape
RECORD/PLAYBACK HEAD AZIMUTH ADJUSTMENT
DECK A DECK B
Precaution
1. Clean the following parts with a denatured alcohol-moistened
swab:
record/playback heads
pinch rollers
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head
demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
set
SP RELAY board
CN804
Pin
CN804
Pin
2
(L-CH)
Pin
5
(R-CH)
SP RELAY board
CN804
Pin
CN804
Pin
3
(GND)
+
–
–
level meter
test tape
P-4-A100
(10 kHz, –10 dB)
P-4-A100
(10 kHz, –10 dB)
3.06 N • m to 6.96 N • m
31 to 71 g • cm
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • m
2 to 6 g • cm
(0.02 – 0.08 oz • inch)
3.06 N • m to 6.96 N • m
31 to 71 g • cm
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • m
2 to 6 g • cm
(0.02 – 0.08 oz • inch)
6.96 N • m to 14.02 N • m
71 to 143 g • cm
(0.98 – 1.99 oz • inch)
9.80 N • m
100 g or more
(3.53 oz or more)
9.80 N • m
100 g or more
(3.53 oz or more)
Mode
Torque meter
CQ-102C
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
CQ-403A
CQ-403R
Meter reading
FWD
FWD
back tension
REV
REV
back tension
FF/REW
FWD tension
REV tension
Tape
Signal
Used for
P-4-A100
10 kHz, –10 dB
Azimuth Adjustment
WS-48B
3 kHz, 0 dB
Tape Speed Adjustment
35
HCD-FL5D
Mode: Playback
1. Insert the WS-48B into the deck B.
2. Press the hH button on the deck B.
3. Press the
2. Press the hH button on the deck B.
3. Press the
[CD SYNC HI-DUB]
button in playback mode.
Then at HIGH speed mode.
4. Adjust RV1001 on the SW board so that frequency counter reads
6,000
±
180 Hz.
5. Press the
[CD SYNC HI-DUB]
button.
Then back to NORMAL speed mode.
6. Adjust RV1002 on the SW board so that frequency counter reads
3,000
±
90 Hz.
Adjustment Location: SW board
Sample Value of Wow and Flutter: 0.3% or less W. RMS (JIS)
(WS-48B)
REC BIAS ADJUSTMENT DECK B
Procedure:
In the MC test mode, the “REC memory mode” is convenient for
this adjustment. In the “REC memory mode” , when the REC starts
the input signal FUNCTION is switched to VIDEO automatically.
When the REC stops, the tape returns near to the recording start
position.
In the MC test mode, the “REC memory mode” is convenient for
this adjustment. In the “REC memory mode” , when the REC starts
the input signal FUNCTION is switched to VIDEO automatically.
When the REC stops, the tape returns near to the recording start
position.
1. Press
[MD $VIDEO%]
button to select VIDEO. (This step is not
necessary if the above test mode has already been set)
2. Insert a tape into deck B.
3. A f t e r p r e s s
3. A f t e r p r e s s
[REC PAUSE/START]
button, press
[REC
PAUSE/START]
button, then rec ording start.
4. Mode: Record
5.
Mode: Playback
6. Confirm the playback signal recorded in step 3 becomes
adjustable level as follows.
If these levels are not adjustable level, adjust the RV2 (L-CH)
and RV52 (R-CH) on the SP RELAY board to repeat steps 4
and 5.
If these levels are not adjustable level, adjust the RV2 (L-CH)
and RV52 (R-CH) on the SP RELAY board to repeat steps 4
and 5.
Adjustable level: Playback output of 315 Hz to playback output
of 10 kHz:
±
1.0 dB
Adjustment Location: SP RELAY board
3. Mode: Playback
4. After the adjustments, apply suitable locking compound to the
pats adjusted.
Adjustment Location: Playback Head (Deck A).
Record/Playback/Erase Head (Deck B).
TAPE SPEED ADJUSTMENT
DECK B
Note:
Start the Tape Speed adjustment as below after setting to the test
mode.
In the test mode, the tape speed is high during pressing the
mode.
In the test mode, the tape speed is high during pressing the
[CD SYNC HI-DUB]
button.
Procedure:
1. Press
1. Press
?/1
button to turn the set ON.
2. Press three buttons
x
,
[DISPLAY]
and
[CD SYNC HI-DUB]
simultaneously.
To release from the test mode, press the
To release from the test mode, press the
?/1
button.
SP
REALY
baord
CN804
set
REALY
baord
CN804
set
test tape
P-4-A100
(10 kHz, –10 dB)
P-4-A100
(10 kHz, –10 dB)
pin
5
oscilloscope
L-CH
R-CH
V
H
waveform of oscilloscope
in phase 45
°
90
°
135
°
180
°
good
wrong
pin
3
pin
2
L
R
+
–
–
set
test tape
WS-48B
(3 kHz, 0 dB)
WS-48B
(3 kHz, 0 dB)
SP RELAY board
CN804 Pin
CN804 Pin
3
(GND)
SP RELAY board
CN804
Pin
CN804
Pin
2
(L-CH)
Pin
5
(R-CH)
frequency counter
forward
reverse
attenuator
set
DSP board
MD (AUDIO) (J701)
MD (AUDIO) (J701)
1) 315 Hz
2) 10 kHz
2) 10 kHz
50 mV (–23.8 dB)
600
Ω
blank tape
CN-123
CN-123
AF OSC
+
–
–
set
recorded
portion
portion
SP RELAY board
CN804 Pin
CN804 Pin
3
(GND)
SP RELAY board
CN804
Pin
CN804
Pin
2
(L-CH)
Pin
5
(R-CH)
level meter
36
HCD-FL5D
REC LEVEL ADJUSTMENT DECK B
Procedure:
In the MC test mode, the “REC memory mode” is convenient for
this adjustment. In the “REC memory mode” , when the REC starts
the input signal FUNCTION is switched to VIDEO automatically.
When the REC stops, the tape returns near to the recording start
position.
In the MC test mode, the “REC memory mode” is convenient for
this adjustment. In the “REC memory mode” , when the REC starts
the input signal FUNCTION is switched to VIDEO automatically.
When the REC stops, the tape returns near to the recording start
position.
1. Press
[MD $VIDEO%]
button to select VIDEO. (This step is not
necessary if the above test mode has already been set)
2. Insert a tape into deck B.
3. After press
3. After press
[REC PAUSE/START]
button, press
[REC PAUSE/
START]
button, then recording start.
4. Mode: Record
5. Mode: Playback
6. Confirm the play back signal recorded in step 3 becomes
adjustable level as follows.
If these levels are not adjustable level, adjust the RV53 (R-CH)
on the SP RELAY board to repeat steps 4 and 5.
If these levels are not adjustable level, adjust the RV53 (R-CH)
on the SP RELAY board to repeat steps 4 and 5.
Adjustable level:
CN804 PB level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)
Adjustment Location: SP RELAY board
CN804 PB level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)
Adjustment Location: SP RELAY board
set
DSP board
MD (VIDEO) (J701)
315 Hz, 50 mV (–23.8 dB)
MD (VIDEO) (J701)
315 Hz, 50 mV (–23.8 dB)
blank tape
CS-123
CS-123
600
Ω
attenuator
AF OSC
+
–
–
set
recorded
portion
portion
SP RELAY board
CN804 Pin
CN804 Pin
3
(GND)
SP RELAY board
CN804
Pin
CN804
Pin
5
(R-CH)
level meter
TAPE SPEED
ADJUSTMENT
RV1002
RV1001
(NORMAL) (HIGH)
CN1001
– SW BOARD (Component Side) –
CN804
13
1
– SP RELAY BOARD (Conductor Side) –
REC BIAS
ADJUSTMENT
REC LEVEL
ADJUSTMENT
(L-CH)
(R-CH)
RV52 RV2
RV53
AUTO SERVO ADJUSTMENT
After parts related to the servo circuit (RF amplifier (IC001), DSP
(IC509), motor driver (IC501), EEPROM (IC903) so on) are
replaced, re-adjusting the servo circuit is necessary. Select “ALL”
at “1. DRIVE AUTO ADJUSTMENT” (Refer to page 28 in TEST
MODE) and adjust DVD-SL (single layer), CD and DVD-DL (dual
layer).
(IC509), motor driver (IC501), EEPROM (IC903) so on) are
replaced, re-adjusting the servo circuit is necessary. Select “ALL”
at “1. DRIVE AUTO ADJUSTMENT” (Refer to page 28 in TEST
MODE) and adjust DVD-SL (single layer), CD and DVD-DL (dual
layer).
Ver 1.5
DVD SECTION
RF LEVEL CHECK
Connection:
Procedure:
1.
1.
Connect an oscilloscope to test point 1 pin and 3 pin of
CN901 on the MB board.
CN901 on the MB board.
2.
Turn the power on.
3.
Put the disc (LUV-P01) (Part No.: 4-999-032-01) (CD) in to
playback.
playback.
4.
Confirm that oscilloscope waveform is clear and check RF
signal level is correct or not.
signal level is correct or not.
5.
Put the disc (TDV-520CSO) (Part No.: J-2501-236-A) (DVD)
in to playback.
in to playback.
6.
Perform confirmation in the same manner as step 4.
Note:
A clear RF signal waveform means that the shape “
◊” can be clearly
distinguished at the center of the waveform.
Checking Location:
oscilloscope
MB board
CN901
3
pin
CN901
1
pin
+
–
–
RF signal waveform
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
TIME/DIV: 500 ns
CD: 1.05
±
0.2 Vp-p
DVD: 1.09
±
0.2 Vp-p
– MB Board (Component Side) –
CN901
1
7
Click on the first or last page to see other DHC-FL5D / HCD-FL5D service manuals if exist.