Sony CPF-IX001 / NAS-IX001P Service Manual ▷ View online
SERVICE MANUAL
NETWORK UNIT
NAS-IX001P
Ver. 1.0 2006.09
SPECIFICATIONS
9-887-408-01
2006I05-1
© 2006.09
© 2006.09
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
Published by Sony Techno Create Corporation
US Model
Canadian Model
AEP Model
UK Model
•
NAS-IX001P is network unit in CPF-IX001.
Standard:
IEEE802.11b/g
Channels:
CH1 to CH11
Power requirements:
DC IN: 5 V, 700 mA
General
Operating temperature:
10
°
C to 35
°
C
Design and specifications are subject to change
without notice.
without notice.
2
NAS-IX001P
Notes on chip component replacement
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
TABLE OF CONTENTS
1.
SERVICING NOTES
...............................................
3
2.
GENERAL
...................................................................
4
3.
DISASSEMBLY
3-1.
Disassembly Flow ........................................................... 11
3-2.
Rear Cover Block ............................................................ 11
3-3.
PANEL Board Block ....................................................... 12
3-4.
ETHER Board/Wireless LAN Module (WLAN1) .......... 12
4.
TEST MODE
.............................................................. 13
5.
DIAGRAMS
5-1.
Block Diagram ................................................................ 15
5-2.
Printed Wiring Board – ETHER Board – ........................ 17
5-3.
Schematic Diagram – ETHER Board (1/2) – .................. 18
5-4.
Schematic Diagram – ETHER Board (2/2) – .................. 19
5-5.
Printed Wiring Board – PANEL Board – ........................ 20
5-6.
Schematic Diagram – PANEL Board – ........................... 21
5-7.
Printed Wiring Board – LED Board – ............................. 22
5-8.
Schematic Diagram – LED Board – ................................ 22
5-9.
Printed Wiring Board – CONNECTOR Board – ............ 23
5-10. Schematic Diagram – CONNECTOR Board – ............... 23
6.
EXPLODED VIEWS
6-1.
Cover Section .................................................................. 32
6-2.
PANEL Board Block ....................................................... 33
7.
ELECTRICAL PARTS LIST
................................ 34
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•
Unleaded solder melts at a temperature about 40 ˚C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C.
Caution: The printed pattern (copper foil) may peel away if
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
3
NAS-IX001P
SECTION 1
SERVICING NOTES
FIRMWARE UPDATING
Confirm the firmware version from the network manu, and update
it as follows.
it as follows.
SERVICE POSITION
In checking this set, connect the extension jigs as the figure shown below.
ETHER board
PANEL board
CN1510
CN1508
CN1601
CONNECTOR board
CPF-NW001P
extension jig
(Part No. J-2501-303-A)
(Part No. J-2501-303-A)
extension jig
(inlluding CONNECTOR board)
(Part No. J-2501-304-A)
(inlluding CONNECTOR board)
(Part No. J-2501-304-A)
CN006
CN007
yellow/red/black/white
yellow/black
RADIO RECEPTION CHECK
Note:
For network setting, refer to the Operating Instructions and Quick
Setup Guide of the CPF-IX001.
Setup Guide of the CPF-IX001.
Setting:
[WIRELESS/WIRED] switch:
WIRELESS
Network environment:
Wireless LAN
Distance from wireless router: 10 m
Procedure:
1. Start up the PC with the “M-crew Server Ver. 2.0” installed.
2. Connect each units and turn on the power.
3. Press the [SUSPEND] key on the remote commander to wake-
2. Connect each units and turn on the power.
3. Press the [SUSPEND] key on the remote commander to wake-
up the set and wait until connect with sever PC. If there are
multiple servers, “SERVER?” appears, then press the [ENTER]
key on the remote commander. And select the server by the
multiple servers, “SERVER?” appears, then press the [ENTER]
key on the remote commander. And select the server by the
.
or
>
key on the remote commander, then press the
[ENTER] key.
4. Confirm that the wireless icon indicates 2 or 3 bars.
5. If indicated bar is 1 or less, reduce the distance from wireless
5. If indicated bar is 1 or less, reduce the distance from wireless
router to 1 to 2 m, and confirm that the icon is indicated as
follow.
follow.
Transmission rate is IEEE802.11g: 3 bars
Transmission rate is IEEE802.11b: 2 bars
Transmission rate is IEEE802.11b: 2 bars
Wireless icon
Firmware update window
Update the firmware for the CPF-IX001.
1
The version of the current firmware is displayed.
2
Select the firmware file you want to update.
Click [Browse] to show the dialog for selecting the firmware.
3
Click the button to update.
When you click the button, the firmware confirmation window appears.
If you select the right firmware, updating starts. The CPF-IX001 restarts
automatically when the update is completed.
If you select an incorrect firmware, click [Retry] and select the correct one.
automatically when the update is completed.
If you select an incorrect firmware, click [Retry] and select the correct one.
Notes
• Do not restart the CPF-IX001, set it to the suspended mode, or turn off the
power while updating the firmware.
• Check the following website for CPF-IX001
firmware updates;
USA:
http://esupport.sony.com/?ref=http%3A//
www.sony.com/index.php
Canada:
http://www.sony.ca/sonyca/view/english/warranty/
consumer_support.shtml
Europe:
http://support.sony-europe.com/main/main.asp?l=en
USA:
http://esupport.sony.com/?ref=http%3A//
www.sony.com/index.php
Canada:
http://www.sony.ca/sonyca/view/english/warranty/
consumer_support.shtml
Europe:
http://support.sony-europe.com/main/main.asp?l=en
4
NAS-IX001P
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
Main unit
1 VOLUME +/–
2 FUNCTION
3 Remote sensor (inside)
2 FUNCTION
3 Remote sensor (inside)
4 SURROUND indicator
5 LINE indicator
6 ON indicator
5 LINE indicator
6 ON indicator
Network unit
1 Display window
2 Network illumination
3 LAN port
2 Network illumination
3 LAN port
4 WIRELESS/WIRED selector
5 RESET hole
6 Remote sensor
5 RESET hole
6 Remote sensor
List of button locations and reference pages
1
2
4 3
5
6
Subwoofer
1 Power switch ?/a
Remote control
Buttons for main unit
8 VOL +/–
9 TREBLE +/–
q; BASS +/–
qa EQ OFF
qs SURROUND
wa FUNCTION
9 TREBLE +/–
q; BASS +/–
qa EQ OFF
qs SURROUND
wa FUNCTION
Buttons for network unit
1 SUSPEND (On/Suspended mode)
2 DISPLAY
3 TIME
4 REPEAT
5 PLAY MODE
MUSIC SURFIN’
2 DISPLAY
3 TIME
4 REPEAT
5 PLAY MODE
MUSIC SURFIN’
6 ALL
6 GENRE
6 ARTIST
6 ALBUM
6 GENRE
6 ARTIST
6 ALBUM
7 +/– (select item)
qd WEB RADIO
qf PLAYL IST
qg ENTER
qh MENU +/–
qh
qd WEB RADIO
qf PLAYL IST
qg ENTER
qh MENU +/–
qh
./> (go back/go forward)
qj MENU
qk TCURSOR/CURSORt
qk
qk TCURSOR/CURSORt
qk
m/M (rewind/fast forward)
ql
N (play)
ql
X (pause)
ql
x (stop)
FAVO RITE
w; CALL
w; ADD
w; DEL
w; ADD
w; DEL
ws SLEEP
Quick Setup Guide
Step 2
the CPF-IX001 and your computer.
1
Connect the CPF-IX001 to the network
using a wired connection.
using a wired connection.
Connect the CPF-IX001 to your router (hub) or directly to the
LAN port of the computer. Use the supplied network cable.
Check that the WIRELESS/WIRED selector on the network unit
is set to WIRED.
LAN port of the computer. Use the supplied network cable.
Check that the WIRELESS/WIRED selector on the network unit
is set to WIRED.
Network cable (supplied)
To router (hub) or
LAN port of the
computer
LAN port of the
computer
To LAN port
WIRELESS/WIRED selector
Note
network settings” in the Operating Instructions.
When using the CPF-IX001 with a fixed IP address, refer to “Advanced
2
Turn on the system.
Power switch
3
Press FUNCTION repeatedly until the
LINE indicator on the main unit turns
off.
LINE indicator on the main unit turns
off.
4
Press SUSPEND to start up the network
unit.
unit.
5
Press
and check that music or
sample music is played.
It may take some time until music playback starts depending
on the network status. If “SERVER” appears, refer to “Selecting
another server” in the Operating Instructions.
on the network status. If “SERVER” appears, refer to “Selecting
another server” in the Operating Instructions.
SUSPEND
FUNCTION
wired connection.
This completes the settings when using the CPF-IX001 with a
When using the CPF-IX001 with a wireless connection, press
to stop music playback, then proceed to step 3.
to stop music playback, then proceed to step 3.
Step 1
the CPF-IX001.
Install the M-crew Server Ver. 2.0 software and prepare
1
Check the supplied items.
2
Insert the supplied M-crew Server
Ver. 2.0 software CD-ROM into your
computer.
Ver. 2.0 software CD-ROM into your
computer.
M-c rew ServerVer. 2.0
software CD-ROM
3
Prepare the remote.
Pull out the insulating sheet.
4
Install the CPF-IX001.
Connect the network unit on the main unit, and connect the
subwoofer to the DC IN jack on the back of the main unit.
subwoofer to the DC IN jack on the back of the main unit.
To DC IN jack
To the wall outlet
Network unit
Main unit
Subwoofer
Note
network unit.
Be sure to turn off the subwoofer when connecting or disconnecting the
Step 3
Make the wireless settings.
1
Confirm the settings of your wireless
system.
system.
Check the following items of your wireless LAN router to set the
same information for the CPF-IX001.
same information for the CPF-IX001.
SSID:
Security mode:
Key:
Tips
For details on how to check the wireless LAN router settings, refer to the
operation manual of your wireless LAN router.
operation manual of your wireless LAN router.
details, refer to the operation manual of your wireless LAN router.
Check that your wireless LAN router uses the latest firmware version. For
2
Press MENU.
Press
or
repeatedly until “WLAN SETUP?” appears,
then press ENTER.
The IP address appears in the diaplay.
MENU
ENTER
3
Start up the“WLAN Setup Assistant” on
your computer.
Select [Start] – [All Programs] – [M-crew Server] – [TOOLS]
– [WLAN Setup Assistant].
– [WLAN Setup Assistant].
4
Press NEXT.
Wait a moment for Internet Explorer to start up.
5
Enter“root”to“User name” in the Login
screen. Leave“Password” section blank,
and click [OK] to login.
root
6
Select the language.
7
Click“Wireless LAN Setup” in the Menu.
8
Enter the SSID,Security mode and Key
that you checked in step 1, and click
[Setup].
that you checked in step 1, and click
[Setup].
9
After finishing the setup, click“Restart
Audio Client” in the Menu.
10
Click [Restart.]
11
Disconnect the network cable from the
network unit, and set the WIRELESS/
WIRED selector toWIRELESS.
network unit, and set the WIRELESS/
WIRED selector toWIRELESS.
For details on how to operate the CPF-IX001, refer to
the Operating Instructions located in the “CPF-IX001
Users Manual” folder on the supplied CD-ROM.
the Operating Instructions located in the “CPF-IX001
Users Manual” folder on the supplied CD-ROM.
Follow the instructions on the screen and install the software.
The CPF-IX001 wireless settings are made using the
browser, so first astablish a wired connection between
browser, so first astablish a wired connection between
The Setup screen appears.
The CPF-IX001 restarts, and the settings are complete.
