Sony CMT-X5CD / CMT-X5CDB / CMT-X7CD / CMT-X7CDB Service Manual ▷ View online
CMT-X5CD/X5CDB/X7CD/X7CDB
13
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. FRONT PANEL SUB ASSY
(Page
(Page
14)
2-24. SPEAKER (80 mm)
(PASSIVE RADIATOR) (SP3, SP4)
(Page
34)
2-9. CD MECHANISM DECK BLOCK
(Page
(Page
21)
2-26. LOUDSPEAKER (65 mm)
BLOCK-2 (SP1, SP2)
(Page
36)
2-25. LOUDSPEAKER (65 mm)
BLOCK-1 (SP1, SP2)
(Page
35)
2-27. LOUDSPEAKER (65 mm)
(FULL-RANGE SPEAKER) (SP1)
(Page
37)
2-28. LOUDSPEAKER (65 mm)
(FULL-RANGE SPEAKER) (SP2)
(Page
37)
2-3. LCD BOARD BLOCK
(Page
(Page
15)
2-4. BLUETOOTH MODULE BLOCK,
MAIN CHASSIS BLOCK-1
(Page
16)
2-5. BLUETOOTH MODULE BLOCK,
MAIN CHASSIS BLOCK-2
(Page
17)
2-6. BLUETOOTH MODULE BLOCK,
MAIN CHASSIS BLOCK-3
(Page
18)
2-7. BLUETOOTH MODULE (BT1)
(Page
(Page
19)
2-8. FLEXIBLE FLAT CABLE (9P)
(Page
(Page
20)
2-18. TUNER BOARD BLOCK,
DAB BOARD BLOCK
(Page
29)
2-23. POWER UNIT BLOCK
(Page
(Page
33)
2-22. MAIN BOARD
(Page
(Page
32)
2-19. LID (POWER) BLOCK
(Page
(Page
30)
2-21. MAIN BOARD BLOCK
(Page
(Page
31)
2-10. FFC GUIDE
(Page
(Page
22)
2-20. ETHER BORAD (X7CD/X7CDB)
(Page
(Page
30)
2-17. RC BORAD BLOCK
(Page
(Page
28)
2-15. JACK-NET BOARD BLOCK-2
(X7CD/X7CDB)
(Page
(X7CD/X7CDB)
(Page
27)
2-16. WIFI MODULE (WIFI1)
(X7CD/X7CDB)
(Page
(X7CD/X7CDB)
(Page
27)
2-13. JACK BOARD BLOCK (X5CD/X5CDB)
(Page
(Page
25)
2-14. JACK-NET BOARD BLOCK-1
(X7CD/X7CDB)
(Page
(X7CD/X7CDB)
(Page
26)
2-11. BOTTOM COVER (I)
(Page
(Page
23)
2-12. OPTICAL PICK-UP
(CMS-S76RFS7G)
(CMS-S76RFS7G)
(OP1)
(Page
24)
JIG
When disassembling the unit, use the following jig.
Part No.
Description
9-913-402-33 Tool for Disassembling
Ver. 1.1
CMT-X5CD/X5CDB/X7CD/X7CDB
14
Note: Follow the disassembly procedure in the numerical order given.
2-2. FRONT PANEL SUB ASSY
Note 1: Please spread a sheet under
a unit not to injure front panel.
– Rear bottom view –
– Front bottom view –
4 five screws
(BTTP
M2.6)
Note 3: It is not necessary to remove
these three screws.
3 screw
(BVTP3
u 10)
Note 2: Take care not to injure.
cap rear
2 cap rear
3 screw
(BVTP3
u 10)
2 cap rear
8 front panel sub assy
7 two claws
7 two
claws
7 three claws
6 Remove the front panel sub assy
in the direction of the arrow.
1 Insert a thin pin etc. below the
cap rear and slowly remove
the cap rear.
notch
OK
NG
+RZWRLQVWDOOWKHFDSUHDU
rear panel
block
block
front panel
sub assy
sub assy
5 Insert the jig into the space between
the front panel sub assy and the rear
panel block and remove.
OK
NG
main chassis block
main chassis block
front panel sub assy
front panel sub assy
bottom side
bottom side
notch
+RZWRLQVWDOOWKHIURQWSDQHOVXEDVV\
CMT-X5CD/X5CDB/X7CD/X7CDB
15
2-3. LCD BOARD BLOCK
– Front bottom view –
3 flexible flat cable (9P)
(CN5303)
(CN5303)
4 tapping screw
(B2.6)
(B2.6)
4 tapping screw
(B2.6)
(B2.6)
7 LCD board block
5 two claws
6 Remove the LCD board block
in the direction of the arrow.
1 flexible flat cable (4P)
(CN5301)
(CN5301)
2 flexible flat cable (4P)
(CN2001)
(CN2001)
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note: When installing the flexible flat cable, ensure that
the colored line is not slanted after insertion.
+RZWRLQVWDOOWKHIOH[LEOHIODWFDEOH3))&
long
short
to POWER KEY board
(CN2001)
to LCD board
(CN5301)
CMT-X5CD/X5CDB/X7CD/X7CDB
16
2-4. BLUETOOTH MODULE BLOCK, MAIN CHASSIS BLOCK-1
• Continued on 2-5 (page 17).
– Front top view –
1 FFC cushion (USB)
2 tapping screw
(B2.6)
3 Peel off the adhesive sheet.
4 Peel off the adhesive (BT).
5 Remove the bluetooth
module block in the
direction of the arrow.
Wire setting
FFC cushion (USB)
ferrite core
(FC1)
(FC1)
bluetooth module block
Wire setting
RC board
7 connector
(CN102)
8 connector
(CN103)
6 FFC cushion
(USB)
6 FFC cushion
(USB)
Note 1: Connect the wire so that it does not
cover the remote commander receiver.
FFC cushion (USB)
FFC cushion (USB)
Wire setting
Wire setting
bluetooth module (BT1)
Note 2: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
OK
NG
NG
CN102
Ver. 1.1
Click on the first or last page to see other CMT-X5CD / CMT-X5CDB / CMT-X7CD / CMT-X7CDB service manuals if exist.