Sony CMT-X5CD / CMT-X5CDB / CMT-X7CD / CMT-X7CDB Service Manual ▷ View online
CMT-X5CD/X5CDB/X7CD/X7CDB
33
2-23. POWER UNIT BLOCK
3 coating clip
+RZWRLQVWDOOWKHVOHHYHIHUULWHFODPS)&
cushion
(wire power)
(wire power)
sleeve
ferrite
clamp
(FC7)
ferrite
clamp
(FC7)
2 screw
(BVTP3
u 6)
1 connector
(CN201)
4 power unit block
2 two screws
(BVTP3
u 6)
20 mm
Note: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
OK
NG
NG
–0DLQFKDVVLVEORFNIURQWERWWRPYLHZ–
CMT-X5CD/X5CDB/X7CD/X7CDB
34
2-24. SPEAKER (80 mm) (PASSIVE RADIATOR) (SP3, SP4)
2 speaker (80 mm)
(passive radiator: R-ch)
(SP4)
2 speaker (80 mm)
(passive radiator: L-ch)
(SP3)
1 four screws
(BVTP3
(BVTP3
u 12)
1 four screws
(BVTP3
(BVTP3
u 12)
– Front bottom view –
:ire VettinJ
OK
NG
:ire VettinJ
The edge of the cushion
is aligned.
is aligned.
2 to 3 mm
The edge of the cushion
is inside.
is inside.
OK
NG
The edge of the cushion
is aligned.
is aligned.
2 to 3 mm
The edge of the cushion
is inside.
is inside.
CMT-X5CD/X5CDB/X7CD/X7CDB
35
2-25. LOUDSPEAKER (65 mm) BLOCK-1 (SP1, SP2)
• Continued on 2-26 (page 36).
:LUHVHWWLQJ
OK
NG
:LUHVHWWLQJ
The edge of the cushion
is aligned.
is aligned.
2 to 3 mm
The edge of the cushion
is inside.
is inside.
–)URQWERWWRPYLHZ–
OK
NG
The edge of the cushion
is aligned.
is aligned.
2 to 3 mm
The edge of the cushion
is inside.
is inside.
3 connector
(CN102)
4 connector
(CN103)
1 FFC cushion (USB)
1 FFC cushion (USB)
FFC cushion (USB)
FFC cushion (USB)
:LUHVHWWLQJ
:LUHVHWWLQJ
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
OK
NG
NG
2 Remove the speaker wire
from groove of rear panel block.
2 Remove the speaker wire
from groove of rear panel block.
:LUHVHWWLQJ
RC board
CN102
Note 2: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
Note 1: Connect the wire so that it does not
cover the remote commander receiver.
Ver. 1.1
CMT-X5CD/X5CDB/X7CD/X7CDB
36
2-26. LOUDSPEAKER (65 mm) BLOCK-2 (SP1, SP2)
– Front bottom view –
1 four screws
(BVTP3
(BVTP3
u 12)
1 four screws
(BVTP3
(BVTP3
u 12)
2 Remove the loudspeaker
(65 mm) block in the
direction of the arrow.
2 Remove the loudspeaker
(65 mm) block in the
direction of the arrow.
4 loudspeaker (65 mm) block
(L-ch)
(L-ch)
(SP1)
4 loudspeaker (65 mm) block
(R-ch)
(R-ch)
(SP2)
loudspeaker (65 mm)
(full-range speaker: R-ch)
(SP2)
(full-range speaker: R-ch)
(SP2)
loudspeaker (65 mm)
(full-range speaker: L-ch)
(SP1)
(full-range speaker: L-ch)
(SP1)
+ow to inVtDOO tKe OoXGVSeDNer mm IXOOrDnJe VSeDNer 63 63
terminal position
3 Remove the speaker wire
from hole of rear panel block.
3 Remove the speaker wire
from hole of rear panel block.
terminal position
Top side
Click on the first or last page to see other CMT-X5CD / CMT-X5CDB / CMT-X7CD / CMT-X7CDB service manuals if exist.