DOWNLOAD Sony CMT-SE7 / HCD-SE7 Service Manual ↓ Size: 13.23 MB | Pages: 127 in PDF or view online for FREE

9

Displays the accumulated recording time.

When the accumulated recording time is more than 1 minute, displays the hour and minute

When less than 1 minute, displays “Under 1 min”

The display time indicates the time when the laser is set to high power more, which is about 1/4 of the actual

recording time.

Displays the accumulated playback time.

When the accumulated playback time is more than 1 minute, displays the hour and minute

When less than 1 minute, displays “Under 1 min”

Displays the accumulated rotating time of the spindle motor.

When the accumulated rotating time is more than 1 minute, displays the hour and minute

When less than 1 minute, displays “Under 1 min”

Displays the accumulated number of retry errors during recording and playback.

Displays “r 

 p 

”. 

  after “r” is the number of errors during recording. 

 after “p” is the number of errors during

playback.

This is displayed in hexadecimal from 00 to FF.

Displays the total number of errors.

Displays “total 

”. This is displayed in hexadecimal from 00 to FF.

Displays the past ten rrors.

Displays “0X ErrCd@@”.

X is the history number. The younger the number, the more recent is the history (00 is the latest). @@ is the error

code.

Select the error history number by pressing the  

.

 “R”  or  

>

 “R”   Stick.

Displays the past five retry addresses.

Displays “

 ADRS 

”, 

 is the history number, 

 is the cluster with the retry error.

Select the error history number by pressing the  

.

 “R”  or  

>

 “R”   Stick.

Mode for erasing the error and retry address histories.

Procedure

1. Press the  CLOCK/TIMER SET “R”  button when displayed as “er refresh”.

2. When the display changes to “er refresh?”, press the  ENTER/YES “R”  button

When “Complete!!” is displayed, it means erasure has completed.

Be sure to check the following after executing this mode.

*

Data has been erased.

*

Perform recording and playback, and check that the mechanism is normal.

Mode for erasing the accumulated recording time and accumulated playing time.

Procedure

1. Press the  CLOCK/TIMER SET “R”  button when displayed as “tm refresh”.

2. When the display changes to “tm refresh?”, press the  ENTER/YES “R”  button.

When “Complete!” is displayed, it means erasure has completed.

Mode for erasing the accumulated time of op rec tm, op play tm.

Use these histories as a guide line for the time of replacement of the optical pick-up. If the optical pick-up has

been replaced, perform this procedure and erase the past history.

Procedure

1. Press the  CLOCK/TIMER SET “R”  button when displayed as “op change”.

2. When the display changes to “op change?”, press the  ENTER/YES “R”  button.

When “Complete!” is displayed, it means erasure has completed.

Mode for erasing the accumulated spdl rp tm time.

Use these histories as the guide line for the time of replacement of the spindle motor. If the spindle motor has been

replaced, perform this procedure and erase the past history.

Procedure

1. Press the  CLOCK/TIMER SET “R”  button when displayed as “spdl change”

2. When the display changes to “spdl change?”, press the  ENTER/YES “R”  button.

When “Complete!” is displayed, it means erasure has completed.

op rec tm

op play tm

spdl rp tm

retry err

total err

err history

retry adrs

er refresh

tm refresh

op change

spdl change

10

10

11

12

20

21

22

23

24

30

31

40

41

42

43

50

51

60

Could not perform loading

The changer error occurred

Loading switches combined incorrectly

Timed out without reading the top of PTOC

Could read top of PTOC, but detected error

Timed out without accessing UTOC

Timed out without reading UTOC

Error in UTOC

Could not start playback

Error in sector

A cause of retry occurred during normal recording

Retried due to DRAM overflow

Retry occurred during TOC writing

Retry aborted during S.F editing

Other than access processing, and could not read

address.

Focus NG occurred and overran.

High speed synchronize recording of unlock retry.

11

The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.

The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.

Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveform is output several times.

The disc slot lock function for the antitheft of an demonstration
disc in the store is equipped.

1. Press the  ?/1  button to turn the set on.
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the DVD 

x  

stick and the  

Z 

(DVD) button simulta-

neously for five seconds.

5. The message “LOCKED” is displayed and the slot is locked.

1. Press the  DVD 

x 

stick and the  

Z 

(DVD) button simulta-

neously for five seconds again.

2. The message “UNLOCKED” is displayed and the slot is

unlocked.

When “LOCKED” is displayed, the slot lock is not released by
turning power on/off with the  ?/1  button.

Regarding the notification symbol “R”
Because the number of the operating buttons of this product
are limited, some operations require use of the operating
buttons of the remote commander (RM-SE7 supplied with
the product). When a specific operation requires use of the
operating buttons of the remote commander (RM-SE7), “R”
is added to the specific operating procedure in this manual.
Example  MENU/NO  “R”  The  MENU/NO  button  of remote
commander.

Incorrect operations may be performed if the test mode ia not
entered properly.
In this case, press the  ?/1  button to turn the power off, and
retry to enter the test mode.

If the disc tray does not open and the message “LOCKED”
appears, press the DVD x tick and the  Z  (DVD) button
simultaneously for 5 seconds or longer.
Then remove your fingers from the above stick and the button.
The message “UNLOCKED” appears for 2 seconds and the disc
tray opens.

Extension cable
 (J-1501-103-A)(1.00mm/ 29P/ 300L)

front panel section

DVD mechanism deck
(CDM77A-DVBU20E)

Connect the DMB03 board (CN501) and the RF board (CN002) with the extension cable (29-pins) (J-1501-103-A).

12

MD mechanism deck
(MDM-7S2D)

Extension cable
 (J-1501-011-B)(1.25mm/ 19P/ 300L)

MAIN board

REG board

keep here open.

Slant the MAIN board using the extension cable (19-pins) (J-2501-011-B), and check the MAIN board.