DOWNLOAD Sony CMT-SE7 / HCD-SE7 Service Manual ↓ Size: 13.23 MB | Pages: 127 in PDF or view online for FREE

5

One of the following messages may appear or 
flash in the display during operation. If a 
message appears in the display, be sure to open 
the lid of the unit and confirm the displayed 
message.                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                           

  A disc that cannot be played was inserted 

(page 5).

  A disc with an unsupported Region code was 

inserted.

The JPEG file is an unsupported format.

The disc tray is open.

There is no disc in the player.

You pressed an invalid button.

Appears while the disc tray is opening.

Custom Parental Control or Parental Control is set.

The MP3 file cannot be played.

The function is switching to the DVD.

You pressed PLAY MODE during playback.

The system is reading TOC information of the disc. 
Some buttons are not available.

You stopped play with Resume Play activated 
(page 14).

You tried to program 26 or more tracks (steps).

The MD deck starts the analog recording.

All the tracks on an MD are registered into groups.

The MD deck is pausing the recording because 
silence continued for 30 seconds or more during 
digital recording.

The inserted recordable MD is new, or all tracks on 
the MD have been erased.

  A pre-mastered MD is in the deck.

  You tried to edit in Program or Shuffle Play mode.

  The track is recorded in MDLP mode.

  A pre-mastered MD is in the deck.

  The function is switched to MD.

  There is no disc in the MD deck, or the MD is 

protected against erasure.

  There is no time remaining on the MD.

The editing operation of the MD is completed.

There is no time remaining on the MD.

The MD deck is ejecting the MD. 

An attempt was made to create a new group in 
excess of the maximum number of groups, or there 
are insufficient characters for updating the group 
management information.

  You tried to make an impossible editing 

operation.

  You cannot perform Net MD operations during 

timer playback.

  You cannot combine or erase the tracks due to the 

system limitations of MDs.

Adjustment of the recording level after recording or 
Fade-in and Fade-out procedures have failed since 
the system was either subject to vibration or there is 
a damaged or dirty disc in the tray. 

6

The power was off for a long time, so the system is 
initializing itself.

There is no more space to store track, disc or group 
titles.

While attempting to change the recording level after 
recording, you pressed ENTER/YES without 
actually changing the recording level, so no change 
was made.

There is no disc in the MD deck.

You have reached the end of the MD while pressing 
M during pause mode.

You pressed an invalid button during playback, 
pause, recording or recording pause. 

The MD deck is reading the TOC information of the 
MD.

The MD is playing the specified point for 
confirmation during the A-B Erase Function and the 
Divide Function (pages 55 and 58).

A reading failure has occurred, and the system is 
trying to read the data again.

You attempted to perform another operation while 
in S.F Edit (changing the recording level after 
recording, Fade-in, Fade-out) mode.

You pressed ?/1 while in S.F Edit (changing the 
recording level after recording, Fade-in, Fade-out) 
mode.

The signal was input again after silence continued 
for 3 or more but less than 30 seconds during digital 
recording, and the silence was cut to 3 seconds.

You tried to program 26 or more tracks (steps).

The MD deck is writing the information of recorded 
or edited contents.

You have reached the end of the track while 
adjusting the dividing point during the Divide 
Function.

Tracks and other data that have been checked out on 
Net MD equipment are protected, so you cannot use 
some of the MD editing functions.

The Play Timer and the recording timer start and 
end times are set to the same time.

The Play Timer setting or the recording timer setting 
overlaps with part or all of another timer setting.

You tried to set the clock or timer during timer 
operation.

You tried to select the timer with the clock not set.

You tried to select the timer with the timer not set.

The personal computer is preparing the amount of 
data needed for playback while using the WEB 
RADIO function.

You pressed NET MD on the unit during Check-In 
or Check-Out. Wait until the operation is 
completed.

You tried to pause a music file or a broadcast station 
that cannot be paused while using the MUSIC 
LIBRARY or WEB RADIO function.

You tried to play the music file that cannot be 
played while using the MUSIC LIBRARY function.

The USB cable is not connected properly. Check the 
connection.

Check-In and Check-Out is underway.

7

The personal computer is connecting to the 
broadcast station server while using the WEB 
RADIO function.

You were disconnected from the broadcast station 
server while using the WEB RADIO function.

The Net MD function is on.

The music file is not registered to the MUSIC 
LIBRARY.

The URL is not registered to the WEB RADIO.

The personal computer could not connect to the 
broadcast station server while using the WEB 
RADIO function.

M-crew is not active.

8

1. Press the  ?/1  button to turn on the power.
2. Press the [FUNCTION] button to select the “MD” function.
3. While pressing the  MD x  stick and the [FUNCTION] button at the same time, press the [NET MD] button.
4. Press the  > “R”  button to display “[Service]”. Then press the  ENTER/YES “R”  button.
5. Press the  > “R”  button to display “Err Display”.
6. Press the  ENTER/YES “R”  button to enter the error history display mode and  “op rec tm” appears.
7. Select the desired contents that you want to display or to execute using the  . “R”  stick or the  > “R”  stick.
8. Press the  CLOCK/TIMER SET “R”  button to display or to execute the selected contents.
9. Press the  CLOCK/TIMER SET “R”  button again to return to step 7.
10. Press the  MENU/NO “R”  button. The message “Err Display” appears and you exit the error history mode.
11. Press the  REPEAT/FM MODE “R”  button to exit the test mode.
12. Press the ?/1  button to turn off the power.

Use the self-diagnostics function in the "error history display mode" of the test mode. The least required procedure is described below. Do not enter
any other modes by mistake. If you have entered any other modes accidentally, press the  MENU/NO “R”  button to exit the mode.

Regarding the notification symbol “R”
Because the number of the operating buttons of this product are limited, some operations require use of the operating buttons of the remote
commander (RM-SE7 supplied with the product). When a specific operation requires use of the operating buttons of theremote commander
(RM-SE7),  “R”  is added to the specific operating procedure in this manual.
Example  MENU/NO  “R”  The  MENU/NO  button of remote commander.

Incorrect operations may be performed if the test mode is not entered properly.
In this case, press the  ?/1  button to turn the power off, and retry to enter the test mode.