Sony BDV-IS1000 / HT-IS100 / SA-WIS100 / SS-IS15 Service Manual ▷ View online
SA-WIS100/SS-IS15
5
MAIN BOARD SERVICE POSITION (SA-WIS100)
In checking the MAIN board, prepare jig (extension cable J-2501-231-A: 1.00 mm Pitch, 15 cores, Length 300 mm/J-2501-086-A: 1.00 mm
Pitch, 19 cores, Length 300 mm/J-2501-244-A: 1.00 mm Pitch, 21 cores, Length 300 mm).
In checking the MAIN board, prepare jig (extension cable J-2501-231-A: 1.00 mm Pitch, 15 cores, Length 300 mm/J-2501-086-A: 1.00 mm
Pitch, 19 cores, Length 300 mm/J-2501-244-A: 1.00 mm Pitch, 21 cores, Length 300 mm).
Note: Please take out AMP block assy of the set, and connect it with top panel block.
MAIN board
CN010
CN011
CN1005
Connect jig
(extension cable J-2501-244-A)
(extension cable J-2501-244-A)
Connect jig (extension cable J-2501-231-A)
Connect jig (extension cable J-2501-086-A)
top panel block
CONNECT board
ELECTRICAL DISCHARGE PROCESSING (SA-WIS100)
C903
C934
POWER board
800
Ω/2W
800
Ω/2W
red
black
connector
In checking the board, connect
the lead of red and black by
resistance for electric shock
prevention.
the lead of red and black by
resistance for electric shock
prevention.
C903
and
C934
and
C934
In checking the board,
make a capacitor discharge
of C903 and C934 for
electric shock prevention.
make a capacitor discharge
of C903 and C934 for
electric shock prevention.
CN904
SA-WIS100/SS-IS15
6
HARNESS SETTING (SA-WIS100)
Bend wire from fan into half two times.
Wrap wire from fan with cushion (35T100) one round.
AMP block
CORD BUSH SETTING (SA-WIS100)
cord bush
power cord
160 ± 5 mm
SA-WIS100/SS-IS15
7
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Top panel
" POWER / ACTIVE STANDBY
Green:
the system turns on.
Amber: the Control for HDMI function or the S-AIR STANDBY MODE function is working
while the system is turned off.
No light: the system is turned off, and the Control for HDMI function and the S-AIR STANDBY
MODE function is not working.
# (on/standby)
Press to turn the system on or off.
$ INPUT SELECTOR
Press to select the input source to play back.
% PRESET –/+
Press to go to the previous/next preset radio station.
& VOLUME –/+
Press to adjust the volume level.
' S-AIR
Green:
the S-AIR transmitter (not supplied) is inserted in the subwoofer and the system
establishes sound transmission.
establishes sound transmission.
No light: the system does not establish sound transmission by the S-AIR function.
( Top panel display
Check the system status.
-
VOLUME +
- PRESET +
INPUT SELECTOR
POWER/
ACTIVE STANDBY
About the indications in the top panel display
" Lights up according to the audio input signals.
# SLEEP
Flashes when the Sleep Timer function is active.
$ NIGHT
Lights up when the night mode is on.
% COAX/OPT
Lights up according to the coaxial or optical signal being input.
& TUNED
Lights up when a radio station is received.
' ST/MONO
Lights up according to the stereo or monaural status of the radio.
( Displays system’s status.
Radio frequency, sound field, etc.
) HDMI
Lights up when an HDMI component is being used.
Remote control
Here describes the buttons for amplifier
operation only. For the buttons for operation
of the connected components.
operation only. For the buttons for operation
of the connected components.
• Point the remote at the remote sensor (
) on the
remote commander receiver.
* The 5,
), and VOL + buttons have a tactile dot.
Use it as a guide during operation.
Note
1
2
3
4
6
7
8
0
ENTER
9
TV INPUT
THEATER
TV
AV
TV
BD
DVD
SAT
TOP MENU MENU
BD/DVD
RETURN/EXIT
TV
REPLAY ADVANCE
F1
F2
AMP MENU
CLEAR
DISPLAY
MUTING
TONE
+
G
N
I
N
U
T
-
G
N
I
N
U
T
NIGHT
MODE
GUIDE
FAVORITE
WIDE
PICTURE
JUMP
DMPORT
TUNER/BAND
VIDEO
SOUND FIELD
TV CH -
PRESET -
TV CH +
PRESET +
'
(
H
G
)
.
N
9
Y
5
SYSTEM STANDBY
MENU/HOME
TOOLS/
OPTIONS
TV VOL
MASTER VOL
" (on/standby)
Press to turn the system on or off.
To save the power in standby mode
Press
while the system turns on.
To enter power saving mode, make sure that
the system is in the following status.
the system is in the following status.
– “CTRL: HDMI” is set to “CTRL OFF”.
– “S-AIR STBY” is set to “STBY OFF”.
To cancel standby mode, press
– “S-AIR STBY” is set to “STBY OFF”.
To cancel standby mode, press
once.
# Input buttons
Press one of the buttons to select the
component you want to use.
The buttons are factory assigned to control
Sony components. You can change the
factory settings of the input buttons to suit
the components in your system. For details,
see “Changing the Input Button
Assignments of the Remote”.
component you want to use.
The buttons are factory assigned to control
Sony components. You can change the
factory settings of the input buttons to suit
the components in your system. For details,
see “Changing the Input Button
Assignments of the Remote”.
$ TONE
Press to adjust the bass, middle, and treble
level.
level.
% NIGHT MODE
Press to enjoy sound effects for watching
movies at night.
movies at night.
& AMP MENU
Press to display the menu of the system.
' MUTING
Press to turn off the sound.
( MASTER VOL +/–
Press to adjust the volume.
) $, 9, Y, D or
Press
$, 9, Y or D to select the settings.
Then press
to enter the selection.
* SOUND FIELD
Press to select the sound field.
SA-WIS100/SS-IS15
8
SECTION 3
DISASSEMBLY
•
SA-WIS100 can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW (SA-WIS100)
3-6. MAIN
BOARD
(Page
12)
3-7. TUNER
(FM/AM),
IR-REPEATER
BOARD
(Page
13)
3-8. POWER
BOARD
(Page
13)
3-9. IO
BOARD
(Page
14)
3-10. SPEAKER BOARD,
SAIR
SAIR
BOARD
(Page
14)
3-4. TOP
CHASSIS
(Page
11)
3-5. HDMI
BOARD
(Page
11)
3-2. TOP PANEL BLOCK
(Page
(Page
9)
3-3. AMP
BLOCK
ASSY
(Page
10)
SET
Click on the first or last page to see other BDV-IS1000 / HT-IS100 / SA-WIS100 / SS-IS15 service manuals if exist.