Sony BDV-IS1000 / HT-IS100 / SA-WIS100 / SS-IS15 Service Manual ▷ View online
SA-WIS100/SS-IS15
9
five bosses.
grille frame assy
wire (flat type) (17 core)
(CN1351)
top panel block
eight bosses
boss
(for hot melt glue)
boss (for hot melt glue)
Note 1: Please install a top panel block
after remaining hot melt glue is dissolved
in two bosses by the soldering iron heated up
a little when installing a top panel block.
Note 2: Please be careful about a soldering iron
as it isn't rather too lukewarm.
Note 3: Please install it as a gap of a top panel block
and a cabinet will be the numerical value
of the following figure.
D
top panel block
Gap Specification of top panel block and cabinet
A, B, C and D = 0.7 mm ± 0.5
cabinet
(left side)
(left side)
cabinet
(right side)
(right side)
cabinet
(front or
rear side)
(front or
rear side)
A
B
C
screw
(BVTP3
× 8)
Note: Follow the disassembly procedure in the numerical order given.
3-2. TOP PANEL BLOCK
SA-WIS100/SS-IS15
10
3-3. AMP BLOCK ASSY
four screws
(HDD
damper)
connector
Remove the cushion (70T100).
fabric non woven (15T25)
fabric non woven
(15T25)
fabric non woven (15T25)
wire (flat type) (17 core)
(CN1351)
RT holder (AMP) block
nine screws
(BVTP3
× 8)
RB four dampers
four screws
(HDD
damper)
RE AMP block assy
Please lay the set as you see bottom side.
back side
top side
bottom side
Note: When removing cushion (70T100),
please be sure to exchange it
with
new
cushion
(70T100).
SA-WIS100/SS-IS15
11
3-4. TOP CHASSIS
five screws
(BVTT3
× 6)
five screws
(BVTT3
× 6)
five screws
(BVTT3
× 6)
five screws
(BVTT3
× 6)
top chassis
3-5. HDMI BOARD
screw
(BVTT3
× 6)
R top HDMI bracket
RG HDMI board
RE HDMI bracket
screw
(BVTT3
× 6)
clip bracket
connector (CN3501)
two screws
(BVTP3
× 8)
five screws
(BVTT3
× 6)
screw
(BVTP3
× 8)
connector (CN3509)
RB radiation sheet
wire (flat type) (17 core)
(CN3511)
RT three screws
(BVTT3
× 6)
SA-WIS100/SS-IS15
12
3-6. MAIN BOARD
connector (CN521)
connector (CN561) connector (CN551)
connector (CN541)
connector (CN531)
RB connector (CN1001)
RT connector (CN218)
wire (flat type) (21 core)
(CN1010)
flexible flat cable
(9 core: US, Canadian models) (CN1013/
(11 core: AEP, UK models) (CN1012)
wire (flat type) (15 core)
(CN1011)
wire (flat type) (17 core)
(CN1015)
wire (flat type) (19 core)
(CN1005)
RE three screws
(BVTP3
× 12)
RI three screws
(BVTT3
× 6)
RI five screws
(BVTT3
× 6)
RG heat sink (AMP-WS)
RK wire (flat type) (17 core)
(CN1003)
RL MAIN board
RH two radiation sheets
Click on the first or last page to see other BDV-IS1000 / HT-IS100 / SA-WIS100 / SS-IS15 service manuals if exist.