DOWNLOAD Sony BDV-E500W / HCD-E500W Service Manual ↓ Size: 6.33 MB | Pages: 126 in PDF or view online for FREE

4 three screws (BV3)

5 INCLUDE board

1 connector (CN302)

2 connector (CN301)

3 wire (flat type) (17 core)

5 connector (CN302)

6 four screws

u 8)

4 connector

2 connector (CN904)

1 power cord connector

3 connector (CN906)

9 grass cylindrical fuse (DIA.5) (8A/125V)

7 five screws

qa POWER board

8 Remove the POWER board

0 label fuse (T.H) 

1.  TEST  MODES  OTHER  THAN  THE  TEST  MENU
These are executable test mode even if not entering the test menu.

1-1. Cold Reset
The cold reset clears data except BD/DVD data stored in the RAM 
to initial conditions. Execute this mode when returning the set to 
the customers.
Procedure:
1.  Press the [

?/1

] button to turn the power on.

2.  Press the [

x

], [VOLUME –] and [

Z

] buttons simultaneously 

and hold down (around 5 seconds).

3.  The message “COLD RESET” appears on fl uorescent indica-

tor tube, then becomes standby states.

1-2.  AM Step Change 
The step interval of AM channels can be toggled between 9 kHz 
and 10 kHz.
Procedure:
1.  Press the [

?/1

] button to turn the power on. 

2.  Press the [FUNCTION] button to select the “AM”.
3.  Press the [

N

] and [FUNCTION] buttons simultaneously and 

hold down (around 5 seconds).

4.  The message “AM 9K STEP” or “AM 10K STEP” appears 

on the fluorescent indicator tube, and the AM channel step is 
changed.

1-3.  Disc Tray Lock
This mode let you lock the disc tray. When this mode is activated, 
the disc will not eject when the [

Z

] button is pressed. The message 

“LOCKED” will be displayed on the fluorescent indicator tube.
Procedure:
1.  Press the [

?/1

] button to turn the power on. 

2.  Press the [FUNCTION] button to select the “BD/DVD”.
3.  Press the [

x

] and [

Z

] buttons simultaneously and hold down 

until “LOCKED” or “UNLOCKED” displayed on the fluores-
cent indicator tube (around 5 seconds).

2.  TEST  MODES  IN  THE  TEST  MENU
These are the test modes done in the test menu.

Setting method of the test menu:
1.  Press the [

?/1

] button to turn the power on.

2.  Press three button in order of the [CLEAR] 

→ [

3

] 

→ [0] → 

[1] 

→ [0] → [ANGLE] on the remote commander (Make the 

interval when each button is pressed within two seconds).

3.  The message “TEST MENU” appears on the fluorescent indi-

cator tube and enter the test menu.

2-1. Panel Test
Procedure:
1.  Enter the test menu.
2. Press the [

M

]/[

m

] buttons on the remote commander to select 

the “PANEL TEST”, and press the [

3

] button on the remote 

commander.

3.  LEDs and all segments in fl uorescent indicator tube are lighted 

up. And half segments in fl uorescent indicator tube are lighted 
up, others half segments in fl uorescent indicator tube are light-
ed up, then LEDs and all segments in fl uorescent indicator tube 
are lighted up. This operation is repeated.

4.  When all segments in fl uorescent indicator tube are lighted up 

in the state of step 3, press the [VOLUME +] button on the 
remote commander and model information is displayed on the 
fl uorescent indicator tube.

 

Each time the [VOLUME +] button on the remote commander 
is pressed, the display changes from destination information, 
MC version, SYS version, UI version, DVD version, ST ver-
sion, TA version, DSP version, TM version, CLA version, CEC 
version, SAIR version, DSPF version in this order, and returns 
to the model information display.

 

Each time the [VOLUME –] button on the remote commander 
is pressed, the version and date are switched.

5.  In the state of step 3, press the [FUNCTION] button on the 

remote commander and “K 0” is displayed on the fluorescent 
indicator tube.

 

“K 0” value increases whenever a button on the set is pressed 
or a sensor is touched. However, once a button has been 
pressed, it is no longed taken into account.

 

All buttons on the set are pressed and all sensors are touched, 
“OK” and “K 7” are alternately displayed on the fluorescent 
indicator tube.

6.  To release from this mode, press the [

?/1

] button.

2-2. AMP Test
Procedure:
1.  Enter the test menu.
2. Press the [

M

]/[

m

] buttons on the remote commander to select 

the “AMP TEST”, and press the [

3

] button on the remote 

commander.

3.  The message “MEASURE” appears on the fluorescent indica-

tor tube and enter the AMP test mode.

4.   Press the [BLUE] button on the remote commander, the state 

of D.C.A.C. microphone is displayed on the fl uorescent indica-
tor tube.

 

“D.C.A.C M. IN”  : D.C.A.C. microphone on (Microphone 

detection)

 

“D.C.A.C M. OUT” : D.C.A.C. microphone on (Microphone 

non-detection)

 

“FUNC INPUT” 

: D.C.A.C. microphone off

5.   Press the [MUTING] button on the remote commander, “VOL-

UME MIN/NORMAL/MAX” can be switched.

6.   Press the [SUBTITLE] button on the remote commander, the 

message “VACS ON” or “VACS OFF” appears on the fl uores-
cent indicator tube and thus the VACS on/off are changed.

7.   To release from this mode, press the [

?/1

] button.

2-3. Cold Reset
The cold reset clears data except BD/DVD data stored in the RAM 
to initial conditions. Execute this mode when returning the set to 
the customers.
Procedure:
1.  Enter the test menu.
2.  Press the [+] buttons on the remote commander to select the 

“COLD RESET”, and press the [

3

] button on the remote com-

mander.

3.  The message “COLD RESET” appears on the fluorescent indi-

cator tube, then becomes standby states.

2-4. BD Service
This mode describes details in “3. BD SERVICE MODE” (page 
16).

2-5.  Tuner Factory Preset
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-6.  Digital Media Port Test
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-7.  Test Tone Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-8. VACS Display
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-9. VACS On/off
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-10.  DSP Halt Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-11.  DSP Status Display
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-12.  A.CAL Test Disp
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-14.  DMPORT Device Test
Procedure:
1.  Connect the DMPORT device to this set.
2.  Enter the test menu.
3. Press the [

M

]/[

m

] buttons on the remote commander to select 

the “DMPORT TEST”, and press the [

3

] button on the remote 

commander.

4.  The DMPORT device enter to the test mode. The operation of 

the test mode is different according to each device.

 

Example of connecting TDM-iP20:

 

When it enters the test mode and some button operations are 
done, the software version is displayed by blinking LED.

 

X . X X: software version

 

 

second digit of minor version

 

 

fi rst digit of minor version

  

major 

version

 

LED blinks every 0.2 seconds, and LED is turned off for 0.7 
seconds afterwards. The blinking frequency at this time shows 
the majors version.

 

Next, LED blinks every 0.2 seconds, and LED is turned off 
for 0.7 seconds afterwards. The blinking frequency at this time 
shows the fi rst digit of minor version.

 

Next, LED blinks every 0.2 seconds, and LED is turned off 
for 0.7 seconds afterwards. The blinking frequency at this time 
shows the second digit of minor version.

 

Then, it returns to the state that LED blinks.

5.  To release from this mode, press the [

?/1

] button.

2-15.  S-AIR Test Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-16.  S-AIR Radio Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-17.  S-AIR ID Change Mode
Procedure:
1.  Install a wireless transceiver in this set, and communicate with 

the device for the S-AIR communication.

2.  Enter the test menu.
3. Press the [

M

]/[

m

] buttons on the remote commander to select 

the “SAIR ID”, and press the [

3

] button on the remote com-

mander.

4.  The S-AIR ID is changed, and release from the test menu.

Note: Changed S-AIR ID is returned to S-AIR ID set at once with the [S-

AIR ID] switch of this set.

2-18.  EXTRACT ID Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-19.  DMPORT Read Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-20.  DMPORT Write Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-21.  S-Master Setting Switch Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-22.  Parental Reset Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-23.  CD Repeat Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-24.  S-AIR Delay Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-25.  DSP Sampling Frequency Display Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-26.  Power Handling Mode 1
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-27.  Power Handling Mode 2
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

2-28.  Repeat Status Display Mode
Not used for the servicing.
Press the [

?/1

] button if having entered this mode.

Note 1: The operation in this mode must use a remote commander.
Note 2: Connect the monitor with this set with the HDMI cable when you 

execute this mode. This mode cannot be executed when connect-
ing it with CVBS and COMPONENT.

Setting method of the BD service mode:
1.  Press the [

?/1

] button to turn the power on.

2.  Press three button in order of the [CLEAR] 

→ [

3

] 

→ [0] → 

[1] 

→ [0] → [ANGLE] on the remote commander. (Make the 

interval when each button is pressed within two seconds)

3.  The message “TEST MENU” appears on the fluorescent indi-

cator tube and enter the test menu.

4. Press the [

M

]/[

m

] buttons on the remote commander to select 

the “SERVICE IN”, and press the [

3

] button on the remote 

commander.

5.  Enter the BD service mode.

3-1. Main Functions
• ErrorLog/CommandLog 

display

 

Display the error log and command log. Displayed contents 
can also be saved in an USB memory device.

• Diag
 

Performs unit test of devices installed on the board.

• Factory 

Initialize

 

Restores the set to its factory settings.

• Network
 

Checks the network connection.
1.  “Ifconfig” displays the network settings of the unit.
 

Executing this function will run the #Ifconfig command 
and display the result.

2.  “Ping” checks the communication status between the net-

work and terminal of the specified IP address.

 

Executing this function will run the #ping command and 
display the result.

•  Version Up (version update)
 

Performs version update using a disc. For details concerning 
updates, see the attached reference.

• Ststem 

Information

 

Displays the system information of the set.

 

Displays information such as the software version, drive infor-
mation, etc.