Sharp VC-M332HM (serv.man27) User Manual / Operation Manual ▷ View online
GB-33
ADVANCED OPERATION
RECORDING FROM OTHER EQUIPMENT
You can record video and audio signals from various sources, for example a camcorder, onto
a video tape using your VCR.
a video tape using your VCR.
For example, recording from a camcorder connected to LINE 2 IN/DECODER on your VCR:
1.
Load tape into the VCR.
2.
Press
INPUT SELECT
on the remote control
until the VCR display shows
L2
.
3.
If you wish to record from a source connected to
LINE 1 IN/OUT, select
LINE 1 IN/OUT, select
L1
.
4.
If you wish to record from a source connected
with audio phono leads to the sockets on the
front of the VCR (if fitted), select
with audio phono leads to the sockets on the
front of the VCR (if fitted), select
L3
.
NOTE:
•
There are many different ways of connecting external equipment to your VCR. Please
refer to your equipment operation manuals for further information.
refer to your equipment operation manuals for further information.
Optional Scart connection (not supplied)
RF OUT
SORTIE ANTENNE
ANTENNA IN
ENTREE ANTENNE
LINE2(II) IN
/DECODER
CANAL PLUS
/L2(II)
LINE1(I)IN
/OUT
SON/VIDEO
(L1/I)
Mono/Stereo Camcorder
LINE2(II) IN
/DECODER
CANAL PLUS
/L2(II)
LINE IN 3
VIDEO
AUDIO
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
332.book Page 33 Monday, June 14, 1999 12:24 PM
GB-34
SPECIAL FEATURES ON YOUR VCR
POST CODE SECURITY
This feature should allow the Police to identify you as the owner of the VCR if it is stolen. Each
time the VCR is turned on your postcode will be displayed for 5 seconds. Your postcode
cannot be changed or removed without first entering the correct PIN - number.
time the VCR is turned on your postcode will be displayed for 5 seconds. Your postcode
cannot be changed or removed without first entering the correct PIN - number.
If you wish to use this function, follow the procedure below.
1.
Press
MENU
.
2.
Press [
/
] to select SET UP. Press
SET
to
confirm.
3.
Press [
/
] to select POST CODE. Press
SET
to confirm.
4.
Enter your desired PIN number using the
NUMBER BUTTONS
or the [
/
] key.
This must be a 4 digit number in the range
0000 - 9999.
0000 - 9999.
5.
Using the [
/
/
/
] key, enter your
Postcode. Press
SET
to confirm.
6.
Record your PIN number in the box provided
for future reference.
for future reference.
NOTE:
If you wish to change your PIN number at any time:
1.
Follow steps 1 to 3 above.
2.
Enter your current PIN number. Press
SET
to confirm
3.
Press to re-select PIN number.
4.
Enter your new PIN number. Press
SET
to confirm.
IMPORTANT:- Please keep your Operation Manual separate from your
VCR.
VCR.
•
Your Postcode can be changed at any time, but you must first enter your correct PIN
number. If the wrong PIN number is entered, an ERROR message will appear. Re-enter
the correct number.
number. If the wrong PIN number is entered, an ERROR message will appear. Re-enter
the correct number.
POS T COD E
P I N NUMB E R
POS T COD E
- - - - - - - - - - -
S E L E C T :
씱 씰
CHANGE
쑿 쑼
E N T E R : S E T E X I T : ME NU
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
332.book Page 34 Monday, June 14, 1999 12:24 PM
GB-35
SPECIAL FEATURES ON YOUR VCR
LOW POWER FEATURE
To meet new power regulations your VCR can be placed in LOW POWER mode. In LOW
POWER mode the VCR power consumption is reduced to below 1 Watt.
POWER mode the VCR power consumption is reduced to below 1 Watt.
LOW POWER MODE
1.
Press
STAND BY
(
) to place the VCR in STANDBY mode.
2.
Press
STAND BY
(
) again to place the VCR in LOW POWER mode. The VCR digital
display will appear blank.
The VCR power consumption will now be below 1 Watt.
DISENGAGING LOW POWER MODE
Either
Press
STAND BY
(
) to return the VCR to STANDBY mode.
Or
Press
STOP
(
) to use the VCR.
NOTES:
CHILD LOCK
You can lock your VCR with this feature. It will work even when the VCR is in standby,
preventing children from operating the VCR.
preventing children from operating the VCR.
TO ENGAGE CHILD LOCK
Press and hold
on the remote control for about 2 seconds.
flashes and then
remains lit on the VCR display confirming that CHILD LOCK
has been activated.
Regardless of what other operating buttons are touched, the VCR will continue to operate in
its present mode. If CHILD LOCK is activated during playback, once the tape reaches its end,
the VCR will automatically rewind the tape, eject it, and turn the power off.
its present mode. If CHILD LOCK is activated during playback, once the tape reaches its end,
the VCR will automatically rewind the tape, eject it, and turn the power off.
TO DISENGAGE CHILD LOCK
Press and hold
for about 2 seconds.
starts flashing and then disappears. CHILD LOCK is disengaged.
NOTES:
•
With poor signal conditions an increase in noise may be observed on the screen in LOW
POWER mode.
POWER mode.
•
When entering STANDBY, noise may be observed.
•
If a signal is input from an AV source, the VCR may not go into true LOW POWER mode.
•
When disengaging low power mode from the VCR press the Standby button.
•
If you attempt to change modes by pressing another button while CHILD LOCK is on,
the
the
indicator will flash on the VCR display.
•
If power is interrupted for more than 60 seconds (due to power failure etc), CHILD LOCK
may disengage.
may disengage.
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
332.book Page 35 Monday, June 14, 1999 12:24 PM
GB-36
CUSTOMISED INSTALLATION
MANUALLY TUNING A CHANNEL
Normally it will not be necessary to manually tune broadcast programmes except in unusual
circumstances such as poor signal or to suit your preferences.
circumstances such as poor signal or to suit your preferences.
Ensure the video channel is selected on the TV.
1.
Press
MENU
. Then press [
/
] to select SET UP. Press
SET
to confirm.
2.
CHANNEL PRESET
will be highlighted. Press
SET
to confirm.
3.
MANUAL TUNING
will be highlighted. Press
SET
to confirm.
4.
PRESET
will be highlighted. Press [
/
] to choose the required VCR preset channel.
5.
Press [
/
] to select
SOURCE
[if you have previously installed a satellite receiver).
Press [
/
] to choose the required source. If you select SAT go to point 9.
6.
Press [
/
] to select CHANNEL. If you selected CH as the source you have the
option to tune terrestrial channels.
7.
Then press [
/
] to start tuning in either direction. Tuning will stop when a programme
is received. If it is not the desired programme, press [
/
] to continue tuning.
8.
Press [
/
] to select
FINE
TUNING
. (Not available if tuning a
satellite channel). Press and hold [
/
]
until the sharpest colour picture is
obtained.
Go to point 10.
obtained.
Go to point 10.
9.
Press [
/
] to select CHANNEL. Enter
preset satellite numbers using the
NUMBER BUTTONS
or [
/
] to
step through each preset satellite
channel.
channel.
➔
P R E S E T
1
BBC 1
SOURC E CH / CC
S A T
CHANN E L
CH 2 1
F I N E T UN I NG
D E COD E R
ON
O F F
S K I P
ON
O F F
쑿 쑼
: S E L E C T
씱 씰
: CHANGE
S E T
: E N T E R ME NU : E X I T
▲
▲
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
332.book Page 36 Monday, June 14, 1999 12:24 PM
Click on the first or last page to see other VC-M332HM (serv.man27) service manuals if exist.