DOWNLOAD Sharp LC-60LE925E (serv.man22) Service Manual ↓ Size: 4.34 MB | Pages: 84 in PDF or view online for FREE

Set up to three preferred multi audio languages to display 
if the audio languages are available.

Go to “Menu” > “Setup” > “View setting” > 
“Individual setting” > “Digital audio language”.

E

Each time you press 7 on the remote control unit, the 
audio language switches.

Set up to two preferred subtitle languages (including 
subtitles for the hearing impaired) to display if subtitles 
are available.

Go to “Menu” > “Setup” > “View setting” > 
“Individual setting” > “Subtitle”.

 

E 1st language

 

E 2nd language

 

E For hearing impaired

E

Each time you press [ on the remote control unit, the 
subtitle switches.

E

Subtitles for the hearing impaired have priority over each 
of the subtitle language settings (e.g., “1st language”, 
“2nd language”, etc.).

•  Subtitles will not be displayed when the programme does not 

contain subtitle information.

•  Subtitles may not be displayed in 3D mode.

You can select an OSD language from among 23 
languages. Refer to the OSD language column in the 
specification table for the selectable languages (Page 75).

Go to “Menu” > “Setup” > “View setting” > 
“Language”.

You can reduce the TV’s start-up time after turning on the 
power with the remote control unit.

Go to “Menu” > “Setup” > “View setting” > 
“Quick start”.

The TV quickly starts up from standby. 
30 W or more of power consumption is 
required during standby.

Power consumption is small during 
standby.

LC-60LE925E_GB_ver4.indd   39

LC-60LE925E_GB_ver4.indd   39

2010/08/17   16:42:51

2010/08/17   16:42:51

This function enables you to pause the digital TV or 
satellite programme you are watching and start watching 
it again from the paused scene.

 

Press READY.

•  The TV starts temporary recording of the real time 

broadcast in the background.

•  Time shift recordable time is approximately 150 

 

Press I.

•  The TV shows the programme from the scene that the 

TV started recording and the recording carries on.

•  When the TV again playbacks after once pressing H to 

stop the programme, the TV shows the programme from 
the stopped scene.

Start recording the programme you are 
watching.
•  You cannot playback the recorded 

programme until approximately three 
seconds after pressing READY to start 
recording.

I

Playback the recorded programme.

H

Stop the programme in playback (time shift 
recording continues) and go back to the 
real time broadcast (live).

F

Pause the programme in playback (time 
shift recording continues).
•  This function is released in 15 minutes.

S

Reverse (each time you press this button, 
the reverse speed changes in three levels).

J

Fast forward (each time you press this 
button, the fast forward speed changes in 
three levels).

a

Playback after jumping backwards by 10 
seconds.

b

Playback after jumping forward by 30 
seconds.

•  Instead of pressing buttons on the remote control unit, the 

operations above are also available on the screen with the 
operation panel. You can call up this operation panel by 
pressing CONTROL on the remote control unit or select 
“Control (Time shift)” from “Option” > “Option for view”.

•  The operation panel for time shift displays only during time shift 

operation.

•  The “Audio description setting” menu does not work during 

time shift playback.

•  When the amount of memory used for time shift reaches “Full” 

and the blue point is around the left edge of the bar (see 

 and 

 in the Counter section on page 41), you cannot operate some 
functions (F (Pause), S (Reverse), a (Jumping backwards 
by 10 seconds)).

•  Time shift recording will stop in three hours.
•  Time shift does not work for ATV, external inputs, data 

broadcasts and radio broadcasts.

•  To release time shift, press READY, change the DTV/SAT 

channel, change “INPUT” or turn off the power of the TV.

•  Time shift will be released if no operations are performed for 

three hours.

•  Some functions do not work during time shift.
•  Time shift is not actually a recording function, so the recorded 

data is reset when you exit time shift.

•  Time shift does not work automatically, it starts only when you 

press READY.

•  The PIN is required when you use the buttons such as S, 

J, a, b if you set the PIN and the items for “Parental 
rating” except “None” are selected.

•  Recording automatically stops when no signal is received 

(recorded data will be lost).

•  Time shift does not work for any copy protected programmes.
•  For certain signals, resolution may be reduced during time shift 

playback.

Away

You miss the scene while you are away.

Away

You can watch the missed scene when you come back.

You cannot watch the same scene again.

You can watch the same scene again.

LC-60LE925E_GB_ver4.indd   40

LC-60LE925E_GB_ver4.indd   40

2010/08/17   16:42:53

2010/08/17   16:42:53

Channel information displays by pressing p on the remote 
control unit.

Audio (ENG)

STEREO

Video
Subtitle

Off

>> New information

 



The time shift ready icon shows up when 
READY

 is pressed and the TV is recording the 

programme.

 



The status icon shows up depending on what is 
shown on the screen.

The counter displays when you set “On” in “Display the Time 
shift memory” (Go to “Setup” > “Option” > “Time shift setting”).

Time shift
Memory used:

 



The grey bar shows how much memory is in use.

 



This blue point shows how much time has 
progressed.

 



“FULL” shows up when the grey bar reaches 
the right edge. The TV starts overwriting the 
previously recorded data.

•  You can also call up the information above by pressing 

 on the remote control unit or select “Control (Time 

shift)” from “Option” > “Option for view”.

You can choose whether or not to switch the input 
source automatically when receiving an AQUOS LINK or 
an Euro SCART compatible signal on the TV during time 
shift operations.

Go to “Menu” > “Setup” > “Option” > “Time 
shift setting” > “Auto input selection”.

Release time shift when receiving 
an AQUOS LINK or a Euro SCART 
compatible signal. Switch input source 
automatically.

Time shift continues to work. The 
TV does not switch input source 
automatically even when receiving 
an AQUOS LINK or a Euro SCART 
compatible signal.

LC-60LE925E_GB_ver4.indd   41

LC-60LE925E_GB_ver4.indd   41

2010/08/17   16:42:55

2010/08/17   16:42:55

The “WSS” allows the TV to switch automatically among 
the different picture size.

Go to “Menu” > “Setup” > “Option” > “WSS”.

•  Use “Wide mode” if an image does not switch to the 

appropriate picture size. When the broadcast signal contains no 
“WSS” information, the function will not work even if enabled.

•  This function is available for 3D images converted from 2D 

images or normal 2D images.

The “WSS” signal has 4:3 auto-switching that allows you 
to select between “Normal” and “Panorama”.

Go to “Menu” > “Setup” > “Option” > “4:3 
mode”.

Normal range keeping 4:3 or 16:9 
aspect ratio.

Wide image without side bars.

You can select the picture size. Selectable picture size 
varies with the type of signal received.

Keeps the original aspect ratio in a full 
screen display.

For 14:9 letterbox pictures. A thin side 
bar appears on each side, and you may 
also see bars on the top and bottom 
with some programmes.

In this mode, the picture is stretched 
toward each side of the screen. The 
picture may appear similar to “Full” 
depending on broadcast signals.

For 16:9 squeeze pictures.

For 16:9 letterbox pictures. Bars may 
appear on the top and bottom with 
some programmes.

For 14:9 letterbox pictures. Bars may 
appear on the top and bottom with 
some programmes.

Displays with an overscan image. Crops 
all sides of screen.

Displays with an underscan image 
only when receiving a 720p signal. 
Displays with the High-Definition image 
adjusted optimally. Noise may appear 
on the edge of the screen with some 
programmes.

Displays an image with the same 
number of pixels on the screen when 
receiving 1080i/1080p signals only.

•  Some items do not appear depending on the type of received 

signal.

•  You may not be able to change the wide mode while in 3D 

mode.

 

Go to “Menu” > “Setup” > “Option” > “Option 
for view” > “Wide mode”.

•  You can also select an item by pressing f on the 

remote control unit.

•  The menu lists the “Wide mode” options selectable for 

the type of video signal currently received.

 

Press 

a/b to select the desired item.

•  As you toggle the options, each is immediately reflected 

on the screen. There is no need to press 

;.

Basically, if you set “WSS” to “On” in the 
“Option” menu, the optimum “Wide mode” 
is automatically chosen for every broadcast 
or programme played using a VCR or DVD 
player/recorder.

•  Even if you select your desired “Wide mode” manually, the 

TV may automatically switch to the optimum “Wide mode” 
depending on the signal received when “WSS” is set to “On”.

LC-60LE925E_GB_ver4.indd   42

LC-60LE925E_GB_ver4.indd   42

2010/08/17   16:42:56

2010/08/17   16:42:56