DOWNLOAD Sharp LC-60LE855K (serv.man4) Service Manual ↓ Size: 8.03 MB | Pages: 94 in PDF or view online for FREE

•  Turn off the main power and unplug the AC cord from the wall outlet before handling.

• Gently wipe the surface of the front panel with a soft cloth (cotton, flannel, etc.). To 

protect the front panel, do not use a dirty cloth, liquid cleaners, or a chemical cloth 
(wet/dry sheet type cloth, etc.). This may damage the surface of the front panel.

• Wiping with a hard cloth or using strong force may scratch the surface of the front 

panel.

• Use a soft damp cloth to gently wipe the front panel when it is really dirty (It may 

scratch the surface of the front panel when wiped strongly).

•  If the front panel is dusty, use an anti-static brush, which is commercially available, to 

clean it.

To prevent the spread of fire, keep candles or other open flames 
away from this product at all times.

•  Keep the accessory out of the reach of small children. Small children can accidentally 

swallow these parts.

•  If a child accidentally swallows any of these parts, seek immediate medical attention.

•  Do not disassemble or modify the 3D glasses except when recycling the batteries. 

Do not modify the 3D glasses.

•  Batteries must not be exposed to excessive heat such as direct sunlight or fire.
•  Replace only with the same or equivalent type of battery. The battery may explode if 

improperly replaced.

•  Take care not to reverse the battery poles (+ and –) when loading the battery. Follow 

the correct procedure when loading the battery. Loading the battery incorrectly may 
damage the battery or cause it to leak battery fluid, which could result in a fire, injury 
or damage.

•  Do not drop, exert pressure on, or step on the 3D glasses. Doing so may damage the 

glass section, which may result in injury.

•  Be careful not to trap your finger in the hinge section of the 3D glasses. Doing so 

may result in injury.

•  Pay special attention when children are using this product.

•  Do not drop, exert pressure on, or step on the 3D glasses. Doing so may damage the 

glass section, which may result in the risk of injury.

•  Use the 3D glasses only for the specified purpose.
•  Do not move around while wearing the 3D glasses. The surrounding area appears 

dark, which may result in falling or other accidents that may cause injury.

•  Use only the cloth provided with the 3D glasses to clean the lenses. Remove dust 

and soil from the cloth. Any dust or other soiling on the cloth may result in scratches. 
Do not use solvents such as benzene or thinners as doing so may damage the 
coating.

•  When cleaning the 3D glasses, take care not to allow water or other fluids to come 

into contact with the glasses.

•  Always store the 3D glasses in the case provided when not in use.
•  When storing the 3D glasses, avoid very humid or hot locations.

•  If you experience dizziness, nausea, or other discomfort while viewing 3D images, 

discontinue use and rest your eyes.

•  Do not use the 3D glasses if they are cracked or broken.

Remote control unit ( x 1)

“AAA” size battery ( x 2)

Pages 7 and 9

Page 7

Stand unit ( x 1)

For 60/70 inch models

For 80 inch models

Page 5

Page 6

Wireless LAN USB adapter 

(WN8522D 7-JU) ( x 1)

AC cord ( x 1)

(For 80 inch models only)

Page 65

Page 10

Initial setup guide 
(printed document)

Important safety 
precautions 
(printed document)

The listed optional accessories are available for this LCD colour TV. Please 
purchase them at your nearest shop.

•  Additional optional accessories may be available in the near future. When purchasing, 

please read the newest catalogue for compatibility and check the availability.

1

Wall mount bracket 
(For 60/70 inch models)

AN-52AG4

The mark “c” indicates the location of 
the centre of the TV screen.

2

3D glasses

AN-3DG40

Refer to the operation manual of the 3D 
glasses for details regarding usage.

•  Before attaching (or detaching) the stand, unplug the AC cord.
•  Before performing work, spread cushioning over the 

surface on which you will be laying the TV. This will 
prevent it from being damaged.

•  Be sure that two or more persons attach the stand.

•  Attach the stand in the correct direction.
•  Be sure to follow the instructions. Incorrect installation 

•  After attaching the stand to the TV, do not hold the 

•  Do not remove the stand from the TV unless using a 

 

Confirm that there are 9 screws (four M6 screws, 
four M5 screws and one M4 screw) supplied 
with the stand unit.

 

Attach the supporting post to the stand base.

 

1

Insert the claws of the supporting post into 
the stand base.

 

2

Secure the post and the base using the M6 
screws (length: 16 mm) and a screwdriver.

M6 screws

•  Tighten the screws to the holes of the mark “b”.

 

Insert the stand into the openings on the bottom 
of the TV (hold the stand so it will not drop from 
the edge of the base area).

•  Make sure that the stand is firmly inserted into the 

TV. Improper installation may result in tilting of the 
TV set.

Soft cushion

 

Insert and tighten the M5 screws (length: 14 mm) 
into the holes on the rear of the TV.

M5 screws

 

Attaching the stand cover.

 

1

Insert the stand cover.

 

2

Insert and tighten the M4 screw (length: 
8 mm) into the holes of the stand cover.

•  Tighten the screw by pressing the bottom of the 

stand base to the TV side.

M4 screw

•  To detach the stand unit, perform the steps in reverse 

order.

•  A screwdriver is not supplied with this product.
•  In the installation procedure, be careful not to catch 

your fingers between the TV set and the floor.

•  The TV can be rotated up to 20 degrees to the right and 

left.

•  Before attaching (or detaching) the stand, unplug the AC cord.
•  Before performing work, spread cushioning over the 

surface on which you will be laying the TV. This will 
prevent it from being damaged.

•  Be sure that two or more persons attach the stand.

•  Attach the stand in the correct direction.
•  Be sure to follow the instructions. Incorrect installation 

•  After attaching the stand to the TV, do not hold the 

•  Do not remove the stand from the TV unless using a 

 

Confirm that there are 14 screws (eight M6 
screws, four M5 screws and two M4 screws) 
supplied with the stand unit.

 

Attach the supporting post to the stand base.

 

1

Insert the claws of the supporting post into 
the stand base.

 

2

Secure the post and the base using the M6 
screws (length: 20 mm) and a screwdriver.

M6 screws

•  Tighten the screws to the holes of the mark “b”.

 

Insert the stand into the openings on the bottom 
of the TV (hold the stand so it will not drop from 
the edge of the base area).

•  Make sure that the stand is firmly inserted into the 

TV. Improper installation may result in tilting of the 
TV set.

•  Instead of using a soft cushion, the cardboard box 

that the TV is packed in can be assembled and 
used as a work table (refer to the instructions on the 
box to assemble the work table).

Soft cushion

 

Insert and tighten the M5 screws (length: 14 mm) 
into the holes on the rear of the TV.

M5 screws

 

Attaching the stand cover.

 

1

Insert the stand cover.

 

2

Insert and tighten the M4 screws (length: 
8 mm) into the holes of the stand cover.

•  Tighten the screws by pressing the bottom of 

the stand base to the TV side.

M4 screws

•  To detach the stand unit, perform the steps in reverse 

order.

•  A screwdriver is not supplied with this product.
•  In the installation procedure, be careful not to catch 

your fingers between the TV set and the floor.

•  The TV can be rotated up to 20 degrees to the right and 

left.