Sharp LC-60LE822E (serv.man18) User Manual / Operation Manual ▷ View online
Initial auto installation
When the TV is powered on for the first time after
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings one
after another.
Confirm the following before turning on
the power
Is the antenna cable connected?
Is the AC cord plugged in?
Is the MAIN POWER switch turned on (;)?
E
E
E
E
E
Press <a on the TV.
The initial auto installation wizard appears.
Setting the OSD language.
Press a/b/c/d to select the desired language,
and then press ;.
Selecting the location of the TV.
HOME
STORE
Press c/d to select where you will use this TV,
and then press ;.
The confirmation screen pops up only when selecting
“STORE”. Press c/d to select “Yes” or “No”.
HOME: “STANDARD” will be the default value for the “AV
mode” setting.
STORE: “DYNAMIC (Fixed)” will be the default value for
the “AV mode” setting. If the “AV mode” is changed, the
TV will automatically switch back to “DYNAMIC (Fixed)”
when there is no signal input from the TV or remote
control unit for 30 minutes.
STORE: A demonstration image will be displayed after
initial auto installation is completed. If you have chosen
“STORE” by mistake, go to “Setup” > “View setting” >
“Reset” > select “HOME” again.
Setting the country.
Press a/b/c/d to select your country or area,
and then press ;.
This setting screen only appears during the first
installation.
NOTE
If you set “Sweden” in the country setting, you can select
the cable provider “ComHem”. Refer to the
H mark
in the following steps or instructions about the settings for
“ComHem”.
1
•
2
3
•
•
•
•
4
•
•
Starting channel search.
Digital search
Analogue search
Skip
Press a/b to select “Digital search”, “Analogue
search” or “Skip”, and then press ;.
To watch both analogue broadcasts, digital broadcasts
and satellite broadcasts, you should perform the auto
installation setting for each format (Page 32).
If you want to search for more broadcasts, execute
“Additional search” from the “Programme setup” menu
(Pages 32_34).
When you select “Skip”, only “Satellite search” will be
performed. You should perform “Digital search” and
“Analogue search” from “Auto installation” under the
“Setup” menu if needed.
After performing “Digital search” or “Analogue search”,
the screen swithes to the “Satellite search” setting. You
should then execute “Yes” if you want to search for the
satellite channels.
NOTE
If you turn off the power on the TV while performing a channel
search, the initial auto installation wizard will not appear. The
auto installation function allows you to execute the installation
again from “Setup” > “View setting” (Page 32).
The initial auto installation wizard will abort if you leave the TV
unattended for 30 minutes before searching for channels.
After initial auto installation is completed, the default PIN is
automatically set to “1234”. To change the PIN setting, refer to
Password/Lock settings (Page 35). To clear the PIN setting
(PIN input will no longer be needed), refer to
CLEARING THE
PIN (Page 52).
When “Italy” is selected in the country setting, the default age
restriction value is set to 18.
Digital broadcast setting
Press c/d to select “Terrestrial” or “Cable”,
and then press ;.
Terrestrial
Cable
H
When you set “Sweden” in the country setting and select
“Cable” for the searching format, you can select the
cable provider “ComHem”.
Searching for terrestrial broadcasts
The TV searches for, sorts and stores all the
receivable TV stations according to their
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
After searching for DVB-T channels, the
screen switches to the “Satellite search”
setting (Page 13).
5
•
•
•
•
•
•
•
•
•
E
•
Quick guide
Quick guide
Searching for cable broadcasts
To change each item to the appropriate
settings:
Press a/b to select the menu, and then
press ;.
Scrambled stations
[Yes]
Search method
[Channel]
Start frequency
Network ID
[None]
Symbol rate 1
Symbol rate 2
QAM modulation 1
QAM modulation 2
Reset
Search start
Press a/b/c/d or 0_9 to select or input
the appropriate item/value, and then press
;.
;.
Press a/b to select “Search start”, and then
press ;.
Press c/d to select “Yes” to start searching
cable broadcasts, and then press ;.
The TV searches for, sorts and stores all
the receivable TV stations according to their
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
After searching for DVB-C channels, the
screen switches to the “Satellite search”
setting (Page 13).
H
The “Scrambled stations” menu and the “Search method”
menu are not displayed on the screen as each menu item is
fixed.
The value of “Start frequency” and “Network ID” should be set
to the value specified by the cable provider.
E
1
2
3
4
5
•
•
•
Menu
Description
Selectable items
Scrambled
stations
Specifies if you
need to add pay-TV
services.
Yes, No
Search
method
Specifies how you
search channels.
Channel: Extracts all
of information from a
channel (quick, but
needs corresponding
TV stations).
Frequency: Checks
every frequency in
range (slow).
Quick*
2
: All services
are searched by
one frequency. This
menu works only
when your cable
provider provides
the frequency and
the network ID (e.g.,
Homing channel).
Start
frequency
From 47.0_858.0
MHz
Network ID
Specifies the network.
Set this to register
only the specified
network ID without
registering any special
services.
None, 0_65535
Symbol rate
1*
1
The symbol rates
are specified by the
cable provider. Input
the value received for
CATV.
1000_9000
Symbol rate
2*
1
The symbol rates
are specified by the
cable provider. Input
the value received for
CATV.
1000_9000
QAM
modulation 1
16, 32, 64, 128, 256
QAM
modulation 2
None, 16, 32, 64,
128, 256
Set up “Symbol rate 2” if the cable provider uses several
symbol rates.
When “Quick” is selected, “Scrambled stations” is automatically
set to “No”.
When “Quick” is selected, “None” for the “Network ID” menu
cannot be selected.
H
When you set “Sweden” in the country setting and select
“Cable” for the searching format, you can select the cable
provider “ComHem”. Follow the screen prompts.
Analogue broadcast setting
The TV searches for, sorts and stores all the
receivable TV stations according to their
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
After searching for analogue channels, the
screen switches to the “Satellite search”
setting (Page 13).
I
J
J
•
•
Searching for satellite broadcasts
Press c/d to select “Yes”, and then press
;
.
Yes
No
If you do not perform “Satellite search” setting, select
“No”, and then press ;.
The current DVB-S/S2 setting screen is displayed.
The current DVB-S/S2 setting screen is displayed.
Next
other
Satellite
LNB Frequency
Low
Low
High
Satellite System
Max. 4 satellites on DiSEqC multiswitch
Change setting
You must first complete “Change setting” before moving
to the “Next” setting.
When starting the satellite search
after setting the scrambled stations:
Press c/d to select “Next”, and then press
;.
NOTE
When you perform the initial auto installation, “Next” cannot be
selected. Completing “Change setting” enables you to select
“Next”.
Start search
other
Satellite
Symbol rate 1
Symbol rate 2
Scrambled stations: No
Change setting
•
•
•
1
•
Start search:
DVB-S/S2 channel searching.
Press c/d to select “Start search”, and then
press ;.
The TV searches for, sorts and stores all the
The TV searches for, sorts and stores all the
receivable TV stations according to their
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
Change setting:
Press c/d to select “Change setting”, and
then press ;.
The setting screen of “Scrambled stations” and “Symbol
rate” is displayed.
Scrambled stations [No]
Search start
SAT1-Symbol rate 1
SAT1-Symbol rate 2
SAT2-Symbol rate 1
SAT1-Symbol rate 2
SAT2-Symbol rate 1
Yes
No
Press a/b to select “Scrambled stations”,
and then press ;.
Scrambled stations: Specifies if you need to add pay-TV
services.
Press c/d to select “Yes”, and then press
;.
Press a/b to select the symbol rate you
Press a/b to select the symbol rate you
want to modify, and then press ;.
Symbol rate: You need to set each symbol rate of all
the satellite broadcasts that the TV can receive (eight
is the maximum number of symbol rates that can be
displayed).
Press c/d to select “Search start”, and then
press ;.
The TV searches for, sorts and stores all the
The TV searches for, sorts and stores all the
receivable TV stations according to their
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
E
1
2
•
E
1
•
2
•
3
4
•
5
6
•
Quick guide
When you change the antenna
connection setting:
Press c/d to select “Change setting” on the
DVB-S/S2 setting screen in the left column,
and then press ;.
The antenna connection setting screen is displayed.
Single satellite
2 satellites on 22kHz switchbox
2 satellites on toneburst switchbox
Max. 4 satellites on DiSEqC multiswitch
Communal satellite system
NOTE
You can select the antenna connection method from the five
types. Consult your dealers before using a method other than
“Single satellite”.
“Single satellite” setting
Press a/b to select “Single satellite”, and
then press ;.
Press a/b to select “SAT1 [None]” to display
Press a/b to select “SAT1 [None]” to display
the satellite broadcasts that the TV can
receive, and then press ;.
SAT1 [None]
Next
Press a/b/c/d to select your favorite
satellite, and then press ;.
You cannot select “Next” unless you set the satellite
broadcast in step 3.
Atlantic Bird 3
2
•
•
E
1
2
3
•
Press a/b to select “Next”, and then press
;.
SAT1 [ASTRA 1]
Next
Press c/d to select “Yes (0/22kHz)” or “No”
to set the LNB frequency, and then press ;.
Yes (0/22kHz)
No
Press a/b to select the item and press c/d
to adjust 9,000 MHz to 12,000 MHz to the
appropriate value.
EXAMPLE
SAT1 low
SAT1 high
OK
Press a/b to select “OK”, and then press
;.
After completing this setting, the screen
switches to the DVB-S/S2 setting screen
shown in the left column on page 13.
NOTE
Follow the instructions on the screen for “2 satellites on 22kHz
switchbox”, “2 satellites on toneburst switchbox”, “Max. 4
satellites on DiSEqC multiswitch” and “Communal satellite
system” settings.
To set multiple satellite channels, go to “Max. 4 satellites on
DiSEqC multiswitch”.
4
5
6
7
•
•
Quick guide
Click on the first or last page to see other LC-60LE822E (serv.man18) service manuals if exist.