Sharp LC-60LE822E (serv.man18) User Manual / Operation Manual ▷ View online
Password/Lock settings
View setting
PIN
Allows you to use a PIN to protect certain settings from
being accidentally changed.
Go to “Menu” > “Setup” > “View setting” >
“Individual setting” > “PIN”.
NOTE
PIN input is required when executing “PIN”. The default PIN
is “1234”. To clear the PIN setting (PIN input will no longer be
needed), refer to
CLEARING THE PIN (Page 52).
When selecting “Yes”
Register a four-digit password number to use the “PIN”
function.
Press c/d to select “Yes”, and then press
;.
Enter the four-digit number as a PIN using
Enter the four-digit number as a PIN using
0_9 numeric buttons.
Enter the same four-digit number as in step 1
Enter the same four-digit number as in step 1
to confirm.
“The system PIN has been changed successfully”
displays.
Press ;.
NOTE
To view a locked channel, you must enter the PIN (see pages
33 and 34 for locking channels from viewing in DTV, SAT and
ATV mode). When you select a locked channel, a PIN prompt
message pops up. Press 6 to display the PIN input window.
When selecting “No”
Allows you to reset your PIN.
Press c/d to select “Yes”, and then press
;.
NOTE
As a precautionary measure, make a note of your PIN on
the back of this operation manual, cut it out and keep it
in a safe place that children cannot reach.
•
E
1
2
3
•
4
•
E
•
View setting
Parental rating
This function allows DTV services to be restricted. It
prevents children from watching violent or sexual scenes
that may be harmful.
Go to “Menu” > “Setup” > “View setting” >
“Individual setting” > “Parental rating”.
Repeat steps 1 to 4 in
Repeat steps 1 to 4 in
when selecting “Yes”
to the left.
NOTE
“Universal viewing” and “Parental approval pref.” are ratings
used exclusively in France.
Refer to page 58 for details about ratings.
Option
Key lock
This function allows you to lock the buttons on the TV
or remote control unit in order to prohibit children from
changing the channel or volume.
Go to “Menu” > “Setup” > “Option” > “Key
lock”.
Item
Off
Unlocks the buttons.
RC control lock
Locks all buttons on the remote control
unit.
Button control lock
Locks the buttons on the TV except the
power switch.
NOTE
You cannot set both “RC control lock” and “Button control lock”
at the same time.
Cancelling the lock
Press @ on the TV and set to “Off” to cancel the
“RC control lock”. Press @ on the remote control
unit and set to “Off” to cancel the “Button control lock”.
Refer to page 6 for menu operation using @- on the
front of the TV.
1
2
•
•
•
E
•
Basic adjustment
Basic adjustment
Language settings
View setting
Digital audio language
Set up to three preferred multi audio languages to display
if the audio languages are available.
Go to “Menu” > “Setup” > “View setting” >
“Individual setting” > “Digital audio language”.
Switching the multi audio languages
Each time you press 7 on the remote control unit, the
audio language switches.
View setting
Subtitle
Set up to two preferred subtitle languages (including
subtitles for the hearing impaired) to display if subtitles
are available.
Go to “Menu” > “Setup” > “View setting” >
“Individual setting” > “Subtitle”.
Selectable items
1st language
2nd language
For hearing impaired
E
E
E
E
E
Switching subtitle languages
Each time you press [ on the remote control unit, the
subtitle switches.
Off
1st language
2nd language
Set “For hearing impaired” to “Yes”
Subtitles for the hearing impaired have priority over each
of the subtitle language settings (e.g., “1st language”,
“2nd language”, etc.).
EXAMPLE
1st language
(For hearing impaired)
1st language
NOTE
Subtitles will not be displayed when the programme does not
contain subtitle information.
E
E
E
•
View setting
Language
You can select an OSD language from among 23
languages. Refer to the
OSD language column in the
specification table for the selectable languages (Page 56).
Go to “Menu” > “Setup” > “View setting” >
“Language”.
Useful settings
View setting
Quick start
You can reduce the TV’s start-up time after turning on the
power with the remote control unit.
Go to “Menu” > “Setup” > “View setting” >
“Quick start”.
Item
On
The TV quickly starts up from standby.
30 W or more of power consumption is
required during standby.
Off
Power consumption is small during
standby.
Time shift
This function enables you to pause the digital TV or
satellite programme you are watching and start watching
it again from the paused scene.
Press
READY.
The TV starts temporary recording of the real time
broadcast in the background.
Time shift recordable time is approximately 150
minutes for SD or 60 minutes for HD (depending on
the programmes).
Press I.
The TV shows the programme from the scene that the
TV started recording and the recording carries on.
When the TV again playbacks after once pressing H to
stop the programme, the TV shows the programme from
the stopped scene.
Buttons for time shift operation
Buttons
Description
READY
Start recording the programme you are
watching.
You cannot playback the recorded
programme until approximately three
seconds after pressing
READY to start
recording.
•
I
Playback the recorded programme.
H
Stop the programme in playback (time shift
recording continues) and go back to the
real time broadcast (live).
F
Pause the programme in playback (time
shift recording continues).
This function is released in 15 minutes.
•
S
Reverse (each time you press this button,
the reverse speed changes in three levels).
J
Fast forward (each time you press this
button, the fast forward speed changes in
three levels).
a
Playback after jumping backwards by 10
seconds.
b
Playback after jumping forward by 30
seconds.
NOTE
Instead of pressing buttons on the remote control unit, the
operations above are also available on the screen with the
operation panel. You can call up this operation panel by
pressing
CONTROL on the remote control unit or select
“Control (Time shift)” from “Option” > “Option for view”.
The operation panel for time shift displays only during time shift
operation.
When the amount of memory used for time shift reaches “Full”
and the blue point is around the left edge of the bar (see and
in the
Counter section on page 38), you cannot operate
some functions (F (Pause), S (Reverse), a (Jumping
backwards by 10 seconds)).
1
•
•
2
•
•
•
•
•
Time shift does not work for ATV, external inputs, data
broadcasts and radio broadcasts.
To release time shift, press
READY, change the DTV/SAT
channel, change “INPUT” or turn off the power of the TV.
Time shift will be released if no operations are performed for
three hours.
Some functions do not work during time shift.
Time shift is not actually a recording function, so the recorded
data is reset when you exit time shift.
Time shift does not work automatically, it starts only when you
press
READY.
The PIN is required when you use the buttons such as S,
J
J
, a, b if you set the PIN and the items for “Parental
rating” except “None” are selected.
Recording automatically stops when no signal is received
(recorded data will be lost).
Time shift does not work for any copy protected programmes.
For certain signals, resolution may be reduced during time shift
playback.
Examples of time shift usage
When you move away from the TV for a while
(press READY when you move away from the
TV)
Without time shift
Away
You miss the scene while you are away.
With time shift
Away
You can watch the missed scene when you come back.
When you want to watch the same scene
again (you must press READY in advance for
time shift to function)
Without time shift
You cannot watch the same scene again.
With time shift
You can watch the same scene again.
•
•
•
•
•
•
•
•
•
•
Useful viewing functions
Useful viewing functions
Display information regarding time shift
Channel display
Channel information displays by pressing p on the remote
control unit.
Audio (ENG)
STEREO
Video
Subtitle
Off
>> New information
The time shift ready icon shows up when
READY is pressed and the TV is recording the
programme.
The status icon shows up depending on what is
shown on the screen.
Counter
The counter displays when you set “On” in “Display the Time
shift memory” (Go to “Setup” > “Option” > “Time shift setting”).
Time shift
Memory used:
The grey bar shows how much memory is in use.
This blue point shows how much time has
progressed.
“FULL” shows up when the grey bar reaches
the right edge. The TV starts overwriting the
previously recorded data.
NOTE
You can also call up the information above by pressing
CONTROL on the remote control unit or select “Control (Time
shift)” from “Option” > “Option for view”.
•
Option
Auto input selection
You can choose whether or not to switch the input
source automatically when receiving an AQUOS LINK or
an Euro SCART compatible signal on the TV during time
shift operations.
Go to “Menu” > “Setup” > “Option” > “Time
shift setting” > “Auto input selection”.
Item
Enable
Release time shift when receiving
an AQUOS LINK or a Euro SCART
compatible signal. Switch input source
automatically.
Disable
Time shift continues to work. The
TV does not switch input source
automatically even when receiving
an AQUOS LINK or a Euro SCART
compatible signal.
Click on the first or last page to see other LC-60LE822E (serv.man18) service manuals if exist.