Sharp LC-46LE831E (serv.man20) User Manual / Operation Manual ▷ View online
15
Digital broadcast setting
Press c/d to select “Terrestrial” or “Cable”,
and then press ;.
Terrestrial
Cable
E
Searching for terrestrial broadcasts
The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
• To abort the initial auto installation in progress,
press 6.
NOTE
• A region or service selection screen may display
depending on the country settings or cable providers
selections. Follow the screen prompts to make the
selections.
830 series only
After searching for terrestrial channels, the screen
switches to the “Satellite search” setting (Page 16).
E
Searching for cable broadcasts
To change each item to the appropriate settings:
1
Press a/b to select
the menu, and then
press ;.
2
Press a/b/c/d or
0_9
0_9
to select or input
the appropriate item/
value, and then press
;.
Scrambled stations
[Yes]
Search method
[Channel]
Start frequency
Network ID
[None]
Symbol rate 1
Symbol rate 2
QAM modulation 1
QAM modulation 2
Reset
Search start
3
Press a/b to select “Search start”, and then
press ;.
4
Press c/d to select “Yes” to start searching
cable broadcasts, and then press ;.
5
The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
• To abort the initial auto installation in progress,
press 6.
830 series only
After searching for cable channels, the screen
switches to the “Satellite search” setting (Page 16).
Menu
Description
Selectable items
Scrambled
stations
stations
Specifies if you
need to add pay-
TV services.
Yes, No
Search method
Specifies how
you search for
channels.*
2
Channel,
Frequency, Quick
Start frequency
From 47.0_858.0
MHz
Network ID
Specifies the
network.*
3
None, 0_65535
Symbol rate 1/
Symbol rate 2*
Symbol rate 2*
1
Input the value
received for
CATV.*
4
1000_9000
QAM
modulation 1
modulation 1
16, 32, 64, 128,
256
QAM
modulation 2
modulation 2
None, 16, 32, 64,
128, 256
I
Set up “Symbol rate 2” if the cable provider uses
several symbol rates.
J
Details about the “Search method” items are as
follows:
_
_
Channel: Extracts all information from a channel
(quick, but needs corresponding TV stations).
_
_
Frequency: Checks every frequency in range (slow).
_
Quick: All services are searched by one frequency.
This menu works only when your cable provider
provides the frequency and the network ID (e.g.,
Homing channel). When “Quick” is selected,
“Scrambled stations” is automatically set to “No”, and
“None” for the “Network ID” menu cannot be selected.
K
Set this to register only the specified network ID
without registering any special services.
L
The symbol rates are specified by the cable provider.
Analogue broadcast setting
The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
• To abort the initial auto installation in progress,
press 6.
830 series only
After searching for analogue channels, the screen
switches to the “Satellite search” setting (Page 16).
Initial auto installation
16
Searching for satellite broadcasts
(830 series only)
(830 series only)
Press c/d to select “Yes”, and then press ;.
Yes
No
• If you do not perform “Satellite search” setting,
select “No”, and then press ;.
• The current DVB-S/S2 setting screen is displayed.
Next
other
Satellite
LNB Frequency
Low
Low
High
Satellite System
Max. 4 satellites on DiSEqC multiswitch
Change setting
• You must first complete “Change setting” before
moving to the “Next” setting.
1 When you change the antenna
connection setting:
Press c/d to select “Change setting”, and then
press ;.
• The antenna connection setting screen is displayed.
Single satellite
2 satellites on 22kHz switchbox
2 satellites on toneburst switchbox
Max. 4 satellites on DiSEqC multiswitch
Communal satellite system
NOTE
• You can select the antenna connection method from the
five types. Consult your dealers before using a method
other than “Single satellite”.
E
“Single satellite” setting
1
Press a/b to select “Single satellite”, and then
press ;.
2
Press a/b to select “SAT1 [None]” to display
the satellite broadcasts that the TV can receive,
and then press ;.
SAT1 [None]
Next
3
Press a/b/c/d to select your favorite
satellite, and then press ;.
• You cannot select “Next” unless you set the satellite
broadcast in step 3.
Euro Bird 1
Atlantic Bird 1
4
Press a/b to select “Next”, and then press
;.
SAT1 [ASTRA 1]
Next
5
Press c/d to select “Yes (0/22kHz)” or “No” to
set the LNB frequency, and then press ;.
Yes (0/22kHz)
No
6
Press a/b to select the item and press c/d
to adjust 9,000 MHz to 12,000 MHz to the
appropriate value.
EXAMPLE
SAT1 low
SAT1 high
OK
Initial auto installation
17
7
Press a/b to select “OK”, and then press ;.
After completing this setting, the screen
switches to the DVB-S/S2 setting screen shown
in the left column on page 16.
NOTE
• Follow the instructions on the screen for “2 satellites
on 22kHz switchbox”, “2 satellites on toneburst
switchbox”, “Max. 4 satellites on DiSEqC multiswitch”
and “Communal satellite system” settings.
• To set multiple satellite channels, go to “Max. 4 satellites
on DiSEqC multiswitch”.
• Follow the procedure below when the supply of power
is needed for a satellite antenna:
Go to “Menu” > “Setup” > “View setting” > “Channel
settings” > “Antenna setup-DIGITAL” > “Satellite setup”
> “Change setting” > “Communal satellite system”.
2 When starting the satellite search
after setting the scrambled stations:
Press c/d to select “Next” on the DVB-S/S2
setting screen shown in the left column on page
16, and then press ;.
NOTE
• When you perform the initial auto installation, “Next”
cannot be selected. Completing “Change setting”
enables you to select “Next”.
Start search
other
Satellite
Symbol rate 1
Symbol rate 2
Scrambled stations: No
Change setting
E
Start search:
DVB-S/S2 channel searching.
1
Press c/d to select “Start search”, and then
press ;.
2
The TV searches for and stores all the receivable
TV stations according to their settings and the
connected antenna.
• Select “Yes” to sort the search result in alphabetical
order.
• To abort the initial auto installation in progress,
press 6.
E
Change setting:
1
Press c/d to select “Change setting”, and then
press ;.
• The setting screen of “Scrambled stations” and
“Symbol rate” is displayed.
Scrambled stations
[No]
Search start
SAT1-Symbol rate 1
SAT1-Symbol rate 2
SAT2-Symbol rate 1
SAT1-Symbol rate 2
SAT2-Symbol rate 1
Yes
No
2
Press a/b to select “Scrambled stations”, and
then press ;.
• Scrambled stations: Specifies if you need to add
pay-TV services.
3
Press c/d to select “Yes”, and then press ;.
4
Press a/b to select the symbol rate you want
to modify, and then press ;.
• Symbol rate: You need to set each symbol rate of
all the satellite broadcasts that the TV can receive
(eight is the maximum number of symbol rates that
can be displayed).
5
Press c/d to select “Search start”, and then
press ;.
6
The TV searches for and stores all the receivable
TV stations according to their settings and the
connected antenna.
• Select “Yes” to sort the search result in alphabetical
order.
• To abort the initial auto installation in progress,
press 6.
Initial auto installation
18
Checking signal strength and
channel strength (DVB-T/T2*
channel strength (DVB-T/T2*
1
/C/S*
2
/
S2*
2
)
If you install a DVB-T/T2/C/S/S2 antenna for the first
time or relocate it, you should adjust the alignment
of the antenna to receive a good reception while
checking the antenna setup screen.
I
831 series only
J
830 series only
1
Go to “Menu” > “Setup” > “View setting” >
“Channel settings” > “Antenna setup-DIGITAL”.
2
Press a/b to select “Digital setup” or “Satellite
setup”, and then press ;.
E
Checking signal strength
3
Press a/b to select “Signal strength”, and then
press ;.
Signal strength for DVB-T/T2/C
Supply voltage
CH No.
Current
Max.
Signal strength
Signal strength
Channel strength
Current
Max.
Quality
Signal strength for DVB-S/S2
Current
Max.
Signal strength
Signal strength
Channel strength
Current
Max.
Quality
E
Checking channel strength
4
Press a/b to select “Channel strength”, and
then press ;.
• You can input a specified frequency band using the
0_9
numeric buttons.
Channel strength of DVB-T/T2
Supply voltage
CH No.
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Channel strength
Current
Max.
Quality
Channel strength of DVB-C
Supply voltage
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Symbol rate
QAM modulation
Symbol rate
QAM modulation
Channel strength
Current
Max.
Quality
Channel strength of DVB-S/S2
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Symbol rate
Band
Symbol rate
Band
Channel strength
Current
Max.
Quality
Vert/Low
5
Position and align the antenna so that the
maximum possible values for “Signal strength”
and “Quality” are obtained.
NOTE
• The values of “Signal strength” and “Quality” indicate
when to check the appropriate alignment of the
antenna.
Supplying power to the antenna
You must supply power to the antenna in order
to receive digitally/terrestrially broadcast stations
after connecting the antenna cable to the antenna
terminal on the rear of the TV.
1
Go to “Menu” > “Setup” > “View setting” >
“Channel settings” > “Antenna setup-DIGITAL” >
“Supply voltage”.
2
Press c/d to select “On”, and then press ;.
Initial auto installation
Click on the first or last page to see other LC-46LE831E (serv.man20) service manuals if exist.