Sharp LC-46LE600E (serv.man13) User Manual / Operation Manual ▷ View online
7
Initial installation overview
Follow the steps below one by one when using the TV for the first time. Some steps may not be necessary depending
on your TV installation and connection.
on your TV installation and connection.
Preparation
Connect an antenna cable to the
antenna terminal (Page 8).
antenna terminal (Page 8).
If necessary, insert a CA
card into the CI slot to watch
scrambled broadcasts (Page 15).
card into the CI slot to watch
scrambled broadcasts (Page 15).
Connect the AC cord to the TV
(Page 8).
(Page 8).
Product shape varies in some
countries.
Run the
initial
settings
Turn on (;) the MAIN POWER
switch on the left side of the TV
(Page 4).
switch on the left side of the TV
(Page 4).
Turn on the power using a on
the TV (Page 10).
the TV (Page 10).
Run the initial auto installation
(Page 9).
(Page 9).
Language setting
English
Português
Home/Store setting
HOME
STORE
Country setting
Austria
Finland
Installation start
confirmation
confirmation
Start
Skip
Start searching
channels
✔
✔
✔
✔
Watch TV
Congratulations!
Now you can watch TV.
Now you can watch TV.
If necessary, adjust the antenna
to attain maximum signal
reception (Page 9).
to attain maximum signal
reception (Page 9).
Connect external
devices
Connect external devices
such as a DVD player/
recorder as instructed (Pages
13_14).
such as a DVD player/
recorder as instructed (Pages
13_14).
Connect external audio
devices such as speakers/
amplifier as instructed (Page
15).
devices such as speakers/
amplifier as instructed (Page
15).
Quick guide
LC-LE600E_GB.indd 7
LC-LE600E_GB.indd 7
2009/07/14 14:38:49
2009/07/14 14:38:49
8
Before turning on the power
2
1
*
Cable clamp (Bundle the cables with the clamp)
Standard DIN45325 plug (IEC 169-2) 75
q coaxial cable
Turn on (;) the MAIN POWER switch on the left side of the TV.
AC cord (Product shape varies in some countries)
The AC cord is supplied either with a ferrite core or without a ferrite core. Neither
type causes unnecessary electrical wave emissions or interference.
type causes unnecessary electrical wave emissions or interference.
*
Place the TV close to the AC outlet,
and keep the power plug within
reach.
and keep the power plug within
reach.
Supplying power to the antenna
When an active antenna is used, power must be supplied to the antenna using the following procedures after
connecting the antenna cable to the antenna terminal on the rear of the TV in order to receive terrestrial digital
signals.
connecting the antenna cable to the antenna terminal on the rear of the TV in order to receive terrestrial digital
signals.
Press @ and the “MENU” screen displays.
Press
Press
c/d to select “Setup”.
Press
a/b to select “Antenna Setup”, and then press ;.
Press
a/b to select “Supply Voltage”, and then press ;.
Press
c/d to select “On”, and then press ;.
1
2
3
4
5
2
3
4
5
Mounting the TV on a wall
This TV should be mounted on a wall only with the wall mount bracket and attachment* available from SHARP (Page 30).
The use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
Mounting the LCD colour TV requires special skills and should only be performed by qualified service personnel. Customers
should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting that
results in accident or injury.
You can ask qualified service personnel about using an optional bracket and attachment* to mount the TV to a wall.
To use this TV mounted on a wall, first remove the adhesive tape at the two locations on the rear of the TV, and then use the screws
supplied with the wall mount bracket to secure the bracket to the rear of the TV.
When you mount the TV on a wall, you should attach the supporting post.
Only for 40 inch models.
The use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
Mounting the LCD colour TV requires special skills and should only be performed by qualified service personnel. Customers
should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting that
results in accident or injury.
You can ask qualified service personnel about using an optional bracket and attachment* to mount the TV to a wall.
To use this TV mounted on a wall, first remove the adhesive tape at the two locations on the rear of the TV, and then use the screws
supplied with the wall mount bracket to secure the bracket to the rear of the TV.
When you mount the TV on a wall, you should attach the supporting post.
Only for 40 inch models.
•
•
•
•
•
•
*
*
Quick guide
LC-LE600E_GB.indd 8
LC-LE600E_GB.indd 8
2009/07/14 14:38:50
2009/07/14 14:38:50
9
Initial auto installation
When the TV is powered on for the first time after
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings one
after another.
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings one
after another.
Confirm the following before turning on
the power
the power
Is the antenna cable connected?
Is the AC cord plugged in?
Is the MAIN POWER switch turned on (;)?
Is the AC cord plugged in?
Is the MAIN POWER switch turned on (;)?
E
E
E
E
E
Press a on the TV.
The initial auto installation wizard appears.
Setting the OSD language.
English
Português
Press
a/b to select the desired language, and
then press
;.
Selecting the location of the TV.
HOME
STORE
Press
a/b to select where you will use this TV,
and then press
;.
HOME: “STANDARD” will be the default value for the “AV
MODE” setting.
STORE: “DYNAMIC (Fixed)” will be the default value for
the “AV MODE” setting. If the “AV MODE” is changed,
the TV will automatically switch back to “DYNAMIC
(Fixed)” when there is no signal input from the TV or
remote control unit for 30 minutes.
MODE” setting.
STORE: “DYNAMIC (Fixed)” will be the default value for
the “AV MODE” setting. If the “AV MODE” is changed,
the TV will automatically switch back to “DYNAMIC
(Fixed)” when there is no signal input from the TV or
remote control unit for 30 minutes.
Setting the country.
Austria
Finland
Press
a/b to select your country or area, and
then press
;.
This setting screen only appears during the first
installation.
installation.
1
•
2
3
•
•
4
•
Starting channel search.
Start
Skip
Press
a/b to select “Start” or “Skip”, and then
press
;.
If you want to search for more broadcasts, execute
“Additional Search” from the “Programme Setup” menu
(Page 21).
“Additional Search” from the “Programme Setup” menu
(Page 21).
The TV searches for, sorts and stores all the
receivable TV stations according to their
settings and the connected antenna.
receivable TV stations according to their
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
NOTE
If you turn off the power on the TV after performing step 5 or
if you select “Skip” on step 5, the initial auto installation wizard
will not appear. The auto installation function allows you to
execute the installation again from the “Setup” menu (Page 20).
The initial auto installation wizard will abort if you leave the TV
unattended for 10 minutes before searching for channels in
step 6.
After initial auto installation is completed, the default PIN is
automatically set to “1234”. To change the PIN setting, refer to
Password/Parental lock settings
if you select “Skip” on step 5, the initial auto installation wizard
will not appear. The auto installation function allows you to
execute the installation again from the “Setup” menu (Page 20).
The initial auto installation wizard will abort if you leave the TV
unattended for 10 minutes before searching for channels in
step 6.
After initial auto installation is completed, the default PIN is
automatically set to “1234”. To change the PIN setting, refer to
Password/Parental lock settings
(Page 22). To clear the PIN
setting (PIN input will no longer be needed), refer to CLEARING
THE PIN
THE PIN
(Page 24).
When “Italy” is selected in the country setting, the default PIN is
automatically set to “1234” and the default age restriction value
is set to 18.
automatically set to “1234” and the default age restriction value
is set to 18.
Checking signal strength
If you install an antenna for the first time or relocate it, you
should adjust the alignment of the antenna to receive a
good reception while checking the antenna setup screen.
should adjust the alignment of the antenna to receive a
good reception while checking the antenna setup screen.
Press @ and the “MENU” screen
displays.
displays.
Press
c/d to select “Setup”.
Press
a/b to select “Antenna Setup”, and
then press
;.
Press
a/b to select “Signal Strength”.
NOTE
The values of “Signal Strength” indicates when to check the
appropriate alignment of the antenna.
appropriate alignment of the antenna.
5
•
6
•
•
•
•
•
1
2
3
3
4
•
Quick guide
LC-LE600E_GB.indd 9
LC-LE600E_GB.indd 9
2009/07/14 14:38:51
2009/07/14 14:38:51
10
Daily operation
Switching on/off
Turning on/off the power
Turn on (;) the MAIN POWER switch on the
left side of the TV (Page 4).
left side of the TV (Page 4).
Press a on the TV.
Switch it off by pressing a on the TV.
When turning off the power using a on the TV, EPG data
will be lost.
will be lost.
Standby mode
To standby mode
If the TV is switched on, you can switch it to standby by
pressing B on the remote control unit.
pressing B on the remote control unit.
Switching on from standby
From standby, press B on the remote control unit.
TV indicator status
B (Standby/On
indicator)
Status
Off
Power off
Green
Power on
Red
Standby
NOTE
If you are not going to use this TV for a long period of time, be
sure to remove the AC cord from the AC outlet or turn off (a)
the MAIN POWER switch on the left side of the TV (Page 4).
A small amount of electric power is still consumed even when
a is turned off.
sure to remove the AC cord from the AC outlet or turn off (a)
the MAIN POWER switch on the left side of the TV (Page 4).
A small amount of electric power is still consumed even when
a is turned off.
Switching between digital and
analogue broadcasts
analogue broadcasts
To dial the first
DTV service on the
programme list
DTV service on the
programme list
To dial the first
ATV service on the
programme list
ATV service on the
programme list
NOTE
If the TV cannot search digital broadcasts, the analogue
broadcasts are set from 001 channel.
broadcasts are set from 001 channel.
1
2
•
E
E
•
•
•
Changing channels
With :r/s:
With 0_9:
Selecting an external video
source
source
Once the connection is made,
press b to display the “INPUT
SOURCE” screen, and then press
b or
press b to display the “INPUT
SOURCE” screen, and then press
b or
a/b to switch over to
the appropriate external source
with
with
;.
EXT 2
INPUT SOURCE
TV
TV
EXT 1
EXT 3
Selecting a sound mode
DTV mode
If multi sound modes are received, each time you press
2 the mode switches as follows.
2 the mode switches as follows.
Audio (ENG)
STEREO
L/R
L
R
LR
Audio (ENG)
CH A
CH A
CH B
CH AB
Audio (ENG)
MONO
Press
c/d to select L or R sound when the STEREO or
DUAL MONO screen is displayed.
Audio (ENG)
STEREO
L/R
L
R
LR
NOTE
The sound mode screen disappears in six seconds.
Selectable items vary depending on the received broadcasts.
Selectable items vary depending on the received broadcasts.
ATV mode
Each time you press 2, the mode switches as shown
in the following tables.
in the following tables.
NICAM TV broadcasts selection
Signal
Selectable items
Stereo
NICAM STEREO, MONO
Bilingual
NICAM CH A, NICAM CH B, NICAM CH AB,
MONO
MONO
Monaural
NICAM MONO, MONO
A2 TV broadcasts selection
Signal
Selectable items
Stereo
STEREO, MONO
Bilingual
CH A, CH B, CH AB
Monaural
MONO
NOTE
When no signal is input, the sound mode will display “MONO”.
E
•
•
•
E
•
Watching TV
LC-LE600E_GB.indd 10
LC-LE600E_GB.indd 10
2009/07/14 14:38:52
2009/07/14 14:38:52
Click on the first or last page to see other LC-46LE600E (serv.man13) service manuals if exist.