Sharp LC-32AD5E Service Manual ▷ View online
Unplug the AC cord on the set, then plug it in again.
Turn on the power.
The following window will appear, Up-date for Software will start.
"Uploading inprogress" bar will begin to move.
The following window will appear, Up-date for Software will start.
"Uploading inprogress" bar will begin to move.
RE-WRITE FOR DIGITAL SOFT FIRMWARE
Select the "Connect" from File menu.
Select the "Upload" from Process menu, and select the Software(CB00C73221.urt) in DTV ROM DISC(JG176).
9.
10.
11.
12.
C-6
13.
14.
15.
16.
17.
18.
19.
20.
When the "Uploading inprogress" bar reaches a right edge, the Writing for Digital Soft Firmware will start.
During the writing for Digital Soft Firmware, writing message will appear on the screen.
Finish the writing for Digital Soft Firmware, writing message will disappear.
During the writing for Digital Soft Firmware, writing message will appear on the screen.
Finish the writing for Digital Soft Firmware, writing message will disappear.
Unplug the AC cord, and remove the Serial Communication Change JIG(JG198).
Insert the AC cord again.
After the write, set to the initializing of shipping.
Turn on the power.
Turn on the power.
Press both VOLUME DOWN button on the set and Channel button (1) on the remote control for 2 seconds.
The set will turn into the standby mode.
The set will turn into the standby mode.
Check for the Firmware Version
Turn on the power.
Turn on the power.
Press both VOLUME DOWN button on the set and Channel button (2) on the remote control for 2 seconds.
When the changed version displays, the Re-write will be completed.
When the changed version displays, the Re-write will be completed.
Select the "Disconnect" from File menu.
RE-WRITE FOR DIGITAL SOFT FIRMWARE
C-7
UPDATE FOR VCTP SOFTWARE
1.
2.
3.
4.
5.
6.
7.
Unplug the AC cord, and remove the back cabinet.
Short circuit the 1 pin and 2 pin of CP802 on the Main PCB.
Insert the AC cord.
Remove the short circuit 1 pin and 2 pin of CP802 on the Main PCB.
Set the EU LCD MICON VER UP ROM DISC (JG176) to PC.
Start the "VCTP" (Writing Tools).
Select the "LPT Preferences" from File/Preferences menu, then input "5" to the value of "Delay", and press "OK".
NOTE: This step is not necessary from next time.
NOTE: This step is not necessary from next time.
Using the MICON PROGRAM JIG KIT 25-4 (JG203), connect the PC Terminal and 1~4 pin of CP802 on the
Main PCB (JG203(Red line) =1 pin of CP802).
Main PCB (JG203(Red line) =1 pin of CP802).
8.
Before Update the VCTP Software, it is necessary to install the WRITING TOOLS into the PC.
For the installation of WRITING TOOLS, refer to the "INSTALL FOR WRITING TOOLS".
For the installation of WRITING TOOLS, refer to the "INSTALL FOR WRITING TOOLS".
C-8
C801
C837
C3232
C3228
D3205
R3213
R3216
W815
W811
R3215
R3210
D3204
C3227
C3231
IC801
CP101
CP4305
C818
IC3203
IC3204
IC3601
R3701
R3704
C3627
C3639
C3635
B3609
C3638
C3615
C3659
SH4304
CP802
CP802
Main PCB
Press the “TVT”.
Remove the check of “Bootloader Version”, and check it again.
9.
UPDATE FOR VCTP SOFTWARE
10.
When the number of the side of the check box becomes 40, you can proceed to next step.
If the number doesn’t become 40, check the connection and try again from step 1.
If the number doesn’t become 40, check the connection and try again from step 1.
NOTE :
C-9
Click on the first or last page to see other LC-32AD5E service manuals if exist.