Sharp LC-32AD5E Service Manual ▷ View online
C-2
4.
5.
6.
7.
8.
9.
6.
7.
8.
9.
10.
11.
12.
13.
The unit will now have the correct DATA for the new MEMORY IC.
11.
12.
13.
The unit will now have the correct DATA for the new MEMORY IC.
ADDRESS is now selected and should "blink". Using the UP/DOWN buton on the remote, step through the ADDRESS
until required ADDRESS to be changed is reached.
Press LEFT/RIGHT button to select DATA. When DATA is selected, it will "blink".
Again, step through the DATA using UP/DOWN button until required DATA value has been selected.
Pressing LEFT/RIGHT button will take you back to ADDRESS for further selection if necessary.
Repeat steps 4 to 6 until all data has been checked.
When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
until required ADDRESS to be changed is reached.
Press LEFT/RIGHT button to select DATA. When DATA is selected, it will "blink".
Again, step through the DATA using UP/DOWN button until required DATA value has been selected.
Pressing LEFT/RIGHT button will take you back to ADDRESS for further selection if necessary.
Repeat steps 4 to 6 until all data has been checked.
When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
Turn on the Power.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds.
After the finishing of the initializing of shipping, the unit will turn off automatically.
Turn on the Power.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds.
After the finishing of the initializing of shipping, the unit will turn off automatically.
ADDRESS
DATA
INIT 0000 00
LCD ON 0000
LCD ON 0000
ANALOG M : DB060_70508A
ANALOG S : DB050_70409B
ANALOG S : DB050_70409B
FIG. 2
1.
2.
3.
2.
3.
Turn on the POWER, and set to the TV mode.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.
ADDRESS and DATA should appear as FIG 2.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.
ADDRESS and DATA should appear as FIG 2.
1.
2.
3.
4.
2.
3.
4.
Version
Hardware version A.0
Software version CB00C75091
Hardware version A.0
Software version CB00C75091
OK END
INIT : 5512
VCT-P : A60D LCD ON : 0000
VCT-P : A60D LCD ON : 0000
ANALOG M : DB060_70508A
ANALOG S : DB050_70409B
ANALOG S : DB050_70409B
FIG. 1
Turn on the POWER, and set to the TV mode.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (2) on the remote control for more than 2 seconds.
After the confirmation of MICON VERSION and Digital TV MICON Firmware, turn off the power.
ADDRESS and DATA should appear as FIG 1.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (2) on the remote control for more than 2 seconds.
After the confirmation of MICON VERSION and Digital TV MICON Firmware, turn off the power.
ADDRESS and DATA should appear as FIG 1.
CONFIRMATION OF CHECK SUM, MICON VERSION, DIGITAL TV MICON FIRMWARE AND
POWER ON TOTAL
POWER ON TOTAL
Initial total of MEMORY IC, MICON VERSION, Digital TV MICON Firmware and POWER ON TOTAL HOURS can be
checked on the screen. Total hours are displayed in 16 system of notation.
checked on the screen. Total hours are displayed in 16 system of notation.
NOTE:
WHEN REPLACING EEPROM (MEMORY) IC
If you set a factory initialization, the total hours is reset to "0".
Please refer to "CONFIRMATION OF INITIAL DATA" when SUM DATA is not corresponding.
Please refer to "CONFIRMATION OF INITIAL DATA" when SUM DATA is not corresponding.
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be
taken to ensure correct data settings while making reference to INITIAL SETTING TABLE (Attached "INITIAL DATA").
taken to ensure correct data settings while making reference to INITIAL SETTING TABLE (Attached "INITIAL DATA").
CONFIRMATION OF INITIAL DATA
Initial setting data check sum.
POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
+ (ones digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
+ (ones digit value)
Digital Fimware Fimware
SCALER data check sum.
NOTE: The each item value might be different according to each set.
Main Micon check Version
Sub Micon check Version
Digital
Hardware
Fimware
SERVICING FIXTURES AND TOOLS
Ref. No.
JG203
Part No.
APJG203000
Parts Name
MICON PROGRAM
JIG KIT 25-4
JIG KIT 25-4
Remarks
Up-Date of the VCTP DATA.
EU LCD MICON VER
UP ROM DISC
UP ROM DISC
APJG176133
JG176
Connect the set to personal computer.
JG176
JG212
JG204
JG204
JG203 MICON PROGRAM JIG KIT
25-4
25-4
INSTALL FOR WRITING TOOLS
1.
2.
Set the MICON UPDATE TOOL DISC (JG204) to PC.
Install the LPT driver.
Re-boot the PC.
Install the “Setup_Visual_I2C_v3-2-3b8h.exe”, “Setup_VI2C_for_VCT_Pro_v0101.exe” and “Winupload 4.4.3.exe”.
3.
4.
It is necessary to install according to the PC.
Windows 95/98 : Setup_LptDrv_v0104_9x.exe
Windows 2000/XP : Setup_LptDrvDev_v020201_XP_2000.exe
Windows NT : Setup_LptDrv_v0104_NT.exe
Windows 95/98 : Setup_LptDrv_v0104_9x.exe
Windows 2000/XP : Setup_LptDrvDev_v020201_XP_2000.exe
Windows NT : Setup_LptDrv_v0104_NT.exe
NOTE :
JG204
APJG204000
MICON UPDATE TOOL
DISC
DISC
There is WRITING TOOLS in Disc.
Up-Date of the Digital Soft Firmware.
APJG176130
JG176
DTV ROM DISC
JG201
APJG201000
Serial Communication
Change JIG
Change JIG
Connect the set to personal computer.
Up-Date of the EEPROM DATA.
APJG212002
JG212
EEP ROM DISC
EU LCD MICON VER UP
ROM DISC
DTV ROM DISC
EEPROM DISC
MICON UPDATE TOOL DISC
ROM DISC
DTV ROM DISC
EEPROM DISC
MICON UPDATE TOOL DISC
JG201 Serial Communication
Change JIG
C-3
RE-WRITE FOR DIGITAL SOFT FIRMWARE
Before UPDATE the Digital Soft Firmware, it is necessary to install the WRITING TOOLS into the PC.
For the installation of WRITING TOOL, refer to the "INSTALLING FOR WRITING TOOLS".
For the installation of WRITING TOOL, refer to the "INSTALLING FOR WRITING TOOLS".
Unplug the AC cord, and remove the back cabinet.
Using the Serial Communication Change JIG (JG198) and RS232 Cable, connect the PC terminal and UART
Connector(CP2402) on the DIGITAL PCB Ass'y.
Connector(CP2402) on the DIGITAL PCB Ass'y.
Connect it in order of Digital Pcb Serial Communication Change JIG(JG198) RS232 Cable PC.
Insert the AC cord, turn on the power.
Press both VOLUME DOWN button on the set and Channel button (2) on the remote control for 2 seconds.
Confirm that displayed software version.
Confirm that displayed software version.
Set the Standby mode.
Set the DTV ROM DISC(JG176) to PC.
1.
2.
3.
4.
5.
6.
Serial Communication Change JIG(JG198)
RS232 Cable
TO PC
TO DIGITAL PCB
UART Connector(CP2402)
C-4
7. Start the "Winupload"(Writing tool).
8. Select the "Port Setting" from Process menu, then please set it as follows.
NOTE: This step is not necessary from next time.
RE-WRITE FOR DIGITAL SOFT FIRMWARE
C-5
Click on the first or last page to see other LC-32AD5E service manuals if exist.