DOWNLOAD Sharp LC-32AD5E Service Manual ↓ Size: 5.88 MB | Pages: 92 in PDF or view online for FREE

Fig. 1-9

1.
2.

3.
4.

5.
6.

Remove the 3 screws 

1

.

Remove the Angle PCB-2 and Holder Wire in the
direction of arrow (A).
Remove the 2 screws 

2

.

Remove the Angle LCD Top in the direction of arrow
(B).
Remove the 2 screws 

3

.

Remove the Angle LCD Bottom in the direction of arrow
(C).

(B)

(A)

1

2

Angle LCD Bottom

1

1

2

Angle LCD Top

3

3

Angle PCB-2

(C)

Masking Tape
(Cotton Tape)

IC

Put Masking Tape (cotton tape) around the Flat Package
IC to protect other parts from any damage.
(Refer to Fig. 2-1.)

1.

Fig. 2-1

Some ICs on the PCB are affixed with glue, so be
careful not to break or damage the foil of each IC
leads or solder lands under the IC when removing it.

Masking is carried out on all the parts located within
10 mm distance from IC leads.

Blower type IC
desoldering machine

IC

Heat the IC leads using a blower type IC desoldering
machine. (Refer to Fig. 2-2.)

2.

Fig. 2-2

Do not rotate or move the IC back and forth , until IC
can move back and forth easily after desoldering the
leads completely.

When IC starts moving back and forth easily after
desoldering completely, pickup the corner of the IC using
tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 2-3.)

3.

Blower type IC
desoldering
machine

IC

Fig. 2-3

Tweezers

Peel off the Masking Tape.

4.

Absorb the solder left on the pattern using the Braided
Shield Wire. (Refer to Fig. 2-4.)

5.

Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.

Braided Shield Wire

Soldering Iron

Fig. 2-4

IC pattern

Supply soldering
from upper position
to lower position

IC

Supply the solder from the upper position of IC leads
sliding to the lower position of the IC leads.
 (Refer to Fig. 2-6.)

2.

Fig. 2-6

Soldering Iron

Solder

IC

Absorb the solder left on the lead using the Braided
Shield Wire. (Refer to Fig. 2-7.)

3.

Fig. 2-7

Soldering Iron

Braided Shield Wire

Do not absorb the solder to excess.

IC

When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thin-
tip Soldering Iron. (Refer to Fig. 2-8.)

4.

Fig. 2-8

Thin-tip Soldering Iron

When the IC leads are bent during soldering and/or
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, always be sure to replace the IC in this
case.

Finally, confirm the soldering status on four sides of the
IC using a magnifying glass.
Confirm that no abnormality is found on the soldering
position and installation position of the parts around the
IC. If some abnormality is found, correct by resoldering.

5.

Solder temporarily

Soldering Iron

Take care of the polarity of new IC and then install the
new IC fitting on the printed circuit pattern. Then solder
each lead on the diagonal positions of IC temporarily.
(Refer to Fig. 2-5.)

1.

Fig. 2-5

Solder temporarily

This unit is provided with the following SERVICE MODES so you can repair, examine and adjust easily.

To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote
control for more than a the standard time in the appropriate condition. (See below chart.)

Initialization of factory TV data.
NOTE: If you set factory initialization, the memories are reset

such as the channel setting, and the POWER ON total
hours.

Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".

VOL. DOWN

(Minimum)

1

2 sec.

VOL. DOWN

(Minimum)

6

2 sec.

VOL. DOWN

(Minimum)

9

2 sec.

ALL mode

TV mode

Display of the Adjustment MENU on the screen.
Refer to the "ELECTRICAL ADJUSTMENT"
(On-Screen Display Adjustment).

VOL. DOWN

(Minimum)

2

ALL mode

Check of the SUM DATA, POWER ON total hours and MICON
VERSION on the screen.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".

2 sec.

Releasing of PARENTAL LOCK (DIGITAL).
Refer to the “PARENTAL CONTROL - RATING LEVEL”.

VOL. DOWN

(Minimum)

DTV mode

3

TV mode

2 sec.