Sharp 15FS-25H Service Manual / Specification ▷ View online
MX-2300/2700 N/G SIMULATION 7 – 10
2-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the automatic docu-
ment feeder unit and the related circuits.
ment feeder unit and the related circuits.
Section
RSPF
Item
Operation
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The active sensors and detectors are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The active sensors and detectors are highlighted.
NOTE: SWD_LEN and SWD_AD are not ON/OFF display.
2-3
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the loads
in the automatic document feeder unit and
the control circuits.
the control circuits.
Section
RSPF
Item
Operation
Operation/Procedure
1)
1)
Select the item to be checked with the buttons on the touch
panel.
panel.
2)
Press [EXECUTE] button.
The selected load operation is performed.
When [EXECUTE] button is pressed, the operation is termi-
nated.
The selected load operation is performed.
When [EXECUTE] button is pressed, the operation is termi-
nated.
*1: Since the stamp solenoid is an option unit, it can be operated
only when it is installed.
* For the same loads displayed separately depending on normal
only when it is installed.
* For the same loads displayed separately depending on normal
rotation and rotation, if they are selected together, normal rota-
tion is performed.
In addition, if the load is rotating, reverse rotation is not accepted
until the operation is stopped.
tion is performed.
In addition, if the load is rotating, reverse rotation is not accepted
until the operation is stopped.
3
3-2
Purpose
Operation test/check
Function (Purpose) Used to check the operation of sensor and
detector in the finisher and the related cir-
cuit.
cuit.
Section
Finisher
Item
Operation
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The active sensors and detectors are highlighted.
<Saddle finisher>
The operating conditions of the sensors and detectors are dis-
played.
The active sensors and detectors are highlighted.
<Saddle finisher>
Button
display
Content
Selectable
magnification ratio
Default
value
50
Scan magnification ratio:
50%
50%
COLOR: 50%, 100%,
200%
BLACK (High speed):
100%, 200%
BLACK (Low speed):
50%, 100%, 200%
200%
BLACK (High speed):
100%, 200%
BLACK (Low speed):
50%, 100%, 200%
100%
100
Scan magnification ratio:
100%
100%
200
Scan magnification ratio:
200%
200%
SSET
SPF installation detection
SOCD
SPF open/close detection
SCOV
SPF cover SW
SPED
SPF document empty detection
SPPD1
SPF paper entry detection 1 and random detection
(common)
(common)
SPPD2
SPF paper entry detection 2 PS front
SPPD3
SPF before-scan detection
SPPD4
SPF Reverse gate front detection
SPPD5
SPF Reverse rear detection
SPLS1
SPF Document length detection short
SPLS2
SPF Document length detection long
STMPU
SPF stamp unit installation detection
SWD_LEN
SPF guide plate position
SWD_AD
SPF document detection volume output
CLOSE
BLACK(SLOW)
0
SIMULATION NO.02-01
RSPF AGING
TEST
EXECUTE
150
200
ZOOM
100
%
BLACK(FAST)
COLOR
2-SIDE
1-SIDE
25
50
100
300
400
0
RSPF SENSOR CHECK SWD_LEN: **** SWD_AD: ***
1/1
CLOSE
SIMULATION NO.02-02
TEST
1/1
SSET
SOCD
SCOV
SPED
SPPD1
SPPD2
SPPD3
SPPD4
SPPD5
SPLS1
SPLS2
STMPU
SPFM
SPF transport motor
SPRM_F
SPF paper feed reverse motor normal rotation
SPRM_R
SPF paper feed reverse motor reverse rotation
SPFC
SPF paper feed clutch
SRRC
SPF resist roller clutch
SGS
SPF document exit gate solenoid
STMPS
Finish stamp solenoid (*1)
FJPID
Interface transport unit entry port detection
FJPOD
Interface transport unit exit port detection
FJPDD
Interface transport unit cover detection
FED
Entry port paper detection
FPDHPD
Paddle HP detection
FARHPD
Bundle roller HP detection
FFJHPD
Alignment plate HP detection front
FRJHPD
Alignment plate HP detection rear
FAD
Alignment tray detection
FOBHPD
Discharge belt HP detection
FBED
Tray paper detection
FSLD
Paper surface detection
FFPD
Binding position detection
FFHPD
Binding HP detection
FFRHPD
Binding roller HP detection
FFED
Binding paper detection
FFE
Binding lock detection
FULD
Lift upper limit detection
FLLD
Lift lower limit detection
FLE
Lift lock detection
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
㩷
SIMULATION NO.02̆03
TEST
RSPF OUTPUT CHECK
SPFM
SPRM_F
SPRM_R
SPFC
SRRC
SGS
1/1
EXECUTE
0
STMPS
CLOSE
MX-2300/2700 N/G SIMULATION 7 – 11
<Saddle finisher punch unit>
<Inner finisher>
<Inner finisher punch unit>
3-3
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the load in
the finisher and the control circuit.
Section
Finisher
Item
Operation
Operation/Procedure
1)
1)
Select the item to be checked with the buttons on the touch
panel.
panel.
2)
Press [EXECUTE] button.
The selected load operation is performed.
When [EXECUTE] button is pressed, the operation is termi-
nated.
The selected load operation is performed.
When [EXECUTE] button is pressed, the operation is termi-
nated.
<When the saddle finisher is installed>
<When the inner finisher is installed>
<External punch unit>
<Inner punch unit>
FSHPD
Staple drive HP detection
FSTHPD
Staple shift HP detection
FSD
Staple empty detection
FSUC
Staple connection detection
FSPD
Self prime detection
FMLD
Tray intermediate detection
FFDD
Front door detection
FCD
Upper cover detection
FFDSW
Front door SW detection
FJSW
Joint SW detection
FSSSW
Staple safety SW detection
FFANLK
Fan motor lock detection
FPE
Punch motor lock detection
FPUC
Punch unit connection detection
FPHPD
Punch HP detection
FPDD
Punch dust detection
FPSHPD
Punch horizontal resist HP detection
FPTD
Punch timing detection
FPSD1
Punch horizontal resist detection 1
FPSD2
Punch horizontal resist detection 2
FPSD3
Punch horizontal resist detection 3
FPSD4
Punch horizontal resist detection 4
FED
Entry port paper detection
FBED
Tray paper detection
FULD
Tray upper limit detection
FMLLD
Tray intermediate lower limit detection
FLLD
Tray lower limit detection
FSLD1
Paper surface detection 1
FSLD2
Paper surface detection 2
FRLD
Roller up/down detection
FBRD
Belt separation detection
FFJHPD
Alignment plate HP detection front
FRJHPD
Alignment plate HP detection rear
FJPD
Alignment guide position detection
FSTPD
Staple tray paper detection
FSHPD
Staple drive HP detection
FSTHPD
Staple shift HP detection
FSD
Staple empty detection
FSTD
Staple lead edge position detection
FDSW
Door open detection
FFANLK
Fan motor lock detection
FPRPD
Punch rear position detection
FPUC
Punch unit connection detection
FPHPD
Punch HP detection
FPSHPD
Punch horizontal resist HP detection
FPDD
Punch dust detection
FPPEND
Punch paper rear edge detection
FPPD1
Punch paper surface detection 1
FPPD2
Punch paper surface detection 2
FPPD3
Punch paper surface detection 3
FPPD4
Punch paper surface detection 4
FPPD5
Punch paper surface detection 5
FPPD6
Punch paper surface detection 6
FPDES1
Punch destination detection 1
FPDES2
Punch destination detection 2
FINRPS
Entry port reverse solenoid
FJPM
Interface transport motor
FJFM
Interface transport fan motor
FFM
Transport motor
FPM
Paddle motor
FAM
Bundle paper exit motor
FFJM
Alignment motor front
FRJM
Alignment motor rear
FSM
Staple shift motor
FFSM
Staple motor
FLM
Lift motor
FFC
Folding clutch
FINRPS
Entry port reverse path solenoid
FSLS
Paper surface detection solenoid
FPDS
Paddle solenoid
FBRS
Belt separation solenoid
FRM
Resist motor
FSWM
Oscillation motor
FAM
Bundle paper exit motor
FFJM
Alignment motor front
FRJM
Alignment motor rear
FSM
Staple shift motor
FFSM
Staple motor
FTLM
Tray lift motor
FFANM
Fan motor
FPNM
Punch motor
FPSM
Punch horizontal resist motor
FPNM
Punch motor
FPSM
Punch horizontal resist motor
0
FIN SENSOR CHECK
CLOSE
SIMULATION NO.03-02
TEST
1/2
FJPID
FJPOD
FJPDD
FED
FPDHPD
FARHPD
FFJHPD
FRJHPD
FAD
FOBHPD
FBED
FSLD
FFPD
FFHPD
FFRHPD
FFED
FFE
FULD
FLLD
FLE
MX-2300/2700 N/G SIMULATION 7 – 12
3-10
Purpose
Adjustment
Function (Purpose) Used to adjust the finisher.
Section
Section
Finisher
Item
Operation
Operation/Procedure
1) Select the item according to the adjustment content with [
1) Select the item according to the adjustment content with [
↑] [↓]
buttons.
2) Enter the adjustment value with 10-key.
3) Press [OK] button. (The set value is saved.)
<Saddle finisher>
3) Press [OK] button. (The set value is saved.)
<Saddle finisher>
<Inner finisher>
[Screen (Saddle finisher installed)]
4
4-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the desk/large capac-
ity tray and the related circuit.
ity tray and the related circuit.
Section
Desk/Large capacity tray (LCC)
Item
Operation
Operation/Procedure
The active sensors and detectors are highlighted.
The active sensors and detectors are highlighted.
<Desk sensor>
The active sensors and detectors are highlighted.
The active sensors and detectors are highlighted.
<Desk sensor>
<A4 LCC sensor>
Item
Display
Item
Set
range
Default
value
A
SADDLE POSITION
Saddle binding
position adjustment
position adjustment
0 to 400
200
B
FOLDING POSITION
Saddle folding
position adjustment
position adjustment
0 to 400
200
C
FRONT ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 to 20
10
D
REAR ADJUST
Alignment position
adjustment (rear)
adjustment (rear)
0 to 20
10
E
STAPLE REAR
Staple binding
position adjustment
(one position at the
rear)
position adjustment
(one position at the
rear)
0 to 200
100
F
STAPLE FRONT
Staple binding
position adjustment
(one position in front)
position adjustment
(one position in front)
0 to 200
100
G
STAPLE BOTH
Staple binding
position adjustment
(two positions at the
center)
position adjustment
(two positions at the
center)
0 to 200
100
H
STAPLE PITCH
Staple binding
position adjustment
(two positions in
pitch)
position adjustment
(two positions in
pitch)
0 to 100
50
I
PUNCH CENTER
Punch center
adjustment
adjustment
47 to 53
50
J
PUNCH HOLE
Punch hole position
adjustment
adjustment
0 to 100
50
Item
Display
Item
Set
range
Default
value
A
FRONT ADJUST
Alignment position
adjustment (front)
adjustment (front)
2 to 18
10
B
REAR ADJUST
Alignment position
adjustment (rear)
adjustment (rear)
2 to 18
10
C
STAPLE REAR
Staple binding position
adjustment (one
position at the rear)
adjustment (one
position at the rear)
68 to 132
100
D
STAPLE FRONT
Staple binding position
adjustment (one
position in front)
adjustment (one
position in front)
68 to 132
100
E
STAPLE BOTH
Staple binding position
adjustment (two
positions at the
center)
adjustment (two
positions at the
center)
68 to 132
100
0
SIMULATION NO.03̆03
TEST
FIN LOAD CHECK
EXECUTE
FINRPS
FJPM
FJFM
FFM
FPM
FAM
FFJM
FRJM
FSM
FFSM
FLM
FFC
CLOSE
1/1
1/1
F
STAPLE PITCH
Staple binding position
adjustment (two
positions in pitch)
adjustment (two
positions in pitch)
68 to 132
100
G
PUNCH CENTER
Punch center
adjustment
adjustment
37 to 63
50
H
PUNCH HOLE
Punch hole position
adjustment
adjustment
42 to 58
50
DCSI1
Desk 1 installation detection
DPFD1
Desk 1 transport detection
DLUD1
Desk 1 upper limit detection
DPED1
Desk 1 paper empty detection
DCSPD1
Desk 1 remaining paper quantity detection
DCSS11
Desk 1 rear edge detection 1
DCSS12
Desk 1 rear edge detection 2
DCSS13
Desk 1 rear edge detection 3
DCSS14
Desk 1 rear edge detection 4
DCSI2
Desk 2 instillation detection
DPFD2
Desk 2 transport detection
DLUD2
Desk 2 upper limit detection
DPED2
Desk 2 paper empty detection
DCSPD2
Desk 2 remaining paper quantity detection
DCSS21
Desk 2 rear edge detection 1
DCSS22
Desk 2 rear edge detection 2
DCSS23
Desk 2 rear edge detection 3
DCSS24
Desk 2 rear edge detection 4
DSW_DSK
Desk transport cover open/close detection
LPFD
LCC transport sensor
LUD
LCC tray upper limit sensor
LDD
LCC tray lower limit sensor
LPED
LCC tray paper empty sensor
LCD
LCC tray insertion detection
LDSW
LCC upper open/close detection SW
LRE
LCC lift motor encoder sensor
L24VM
LCC24V power monitor
LLSW
LCC upper limit SW
LTOD
LCC main unit connection detection
Item
Display
Item
Set
range
Default
value
0
A:
A㧦200
B㧦200
C㧦 10
D㧦 10
㧧
SADDLE POSITION
㧧
FOLDING POSITION
㧧
FRONT ADJUSUT
㧧
REAR ADJUSUT
SIMULATION NO.03-10
FINISHER ADJUSTMENT
200
㨇
0 㨪400 㨉
OK
TEST
CLOSE
MX-2300/2700 N/G SIMULATION 7 – 13
4-3
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the loads
in the large capacity tray and the related cir-
cuit.
cuit.
Section
Desk/Large capacity tray (LCC)
Item
Operation
Operation/Procedure
1) Select the item to be checked with the buttons on the touch
1) Select the item to be checked with the buttons on the touch
panel.
2) Press [EXECUTE] button.
The selected load operation is performed.
When [EXECUTE] button is pressed, the operation is termi-
nated.
When [EXECUTE] button is pressed, the operation is termi-
nated.
<Desk load item>
<A4 LCC load item>
4-5
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the
clutches and the related circuits.
Section
Desk/Large capacity tray (LCC)
Item
Operation
Operation/Procedure
Select the item to be checked with the buttons on the touch panel.
The selected clutch operation is performed.
When the operation is normally completed, the button is high-
lighted.
Select the item to be checked with the buttons on the touch panel.
The selected clutch operation is performed.
When the operation is normally completed, the button is high-
lighted.
5
5-1
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the display,
LCD in the operation panel, and control cir-
cuit.
cuit.
Section
Operation panel
Item
Operation
Operation/Procedure
The LCD is changed as shown below. (The contrast changes every
2sec from the current level to MAX
The LCD is changed as shown below. (The contrast changes every
2sec from the current level to MAX
→ MIN → the current level. Dur-
ing this period, each LED is lighted.)
5-2
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the heater
lamp and the control circuit.
Section
Fusing
Item
Operation
Operation/Procedure
1)
1)
Select the item to be checked with the buttons on the touch
panel.
panel.
2)
Press [EXECUTE] button.
The selected heater lamp is operated.
When [EXECUTE] button is pressed, the operation is termi-
nated.
The selected heater lamp is operated.
When [EXECUTE] button is pressed, the operation is termi-
nated.
DPFM
Desk main motor
DLUM1
Desk 1 lift-up motor
DPUC1
Desk 1 paper feed clutch
DLUM2
Desk 2 lift-up motor
DPUC2
Desk 2 paper feed clutch
DTRC
Desk transport clutch
LPFM
LCC transport motor
LLM
LCC lift motor
LPFC
LCC paper feed clutch
LPFS
LCC paper feed solenoid
LTRC
LCC transport clutch
DTRC
Desk transport clutch
LTRC
A4 LCC transport clutch
0
DSK/LCC SENSOR CHECK
CLOSE
SIMULATION NO.04-02
TEST
1/1
DCSI1
DPFD1
DLUD1
DPED1
DCSPD1
DCSS11
DCSS12
DCSS13
DCSS14
DCSI2
DPFD2
DLUD2
DPED2
DCSPD2
DCSS21
DCSS22
DCSS23
DCSS24
DSW_DSK
㩷
㩷
㩷
0
SIMULATION NO.04̆03
TEST
DSK/LCC LOAD CHECK
EXECUTE
1/1
DPFM
DLUM1
DPUC1
DLUM2
DPUC2
DTRC
CLOSE
HL_UM
Heater lamp upper main
HL_LM
Heater lamp lower main
HL_US
Heater lamp upper sub
HL_ALL
All heater lamps ON
CLOSE
1/1
SIMULATION NO. 04㧙05
TEST
DESK/LCC SYNCRONIZING SIGNAL CHECK
LT
RC
: DTRC ON
: LTRC OFF
DTRC
SI MU LA TI O N N O. 0 5㧙01
TEST
SI MU LA TI O N N O. 0 5㧙01
TEST
Click on the first or last page to see other 15FS-25H service manuals if exist.