Sharp XG-PH70X (serv.man10) User Manual / Operation Manual ▷ View online
XG-PH70X/XG-PH70X-N
1 – 13
Optional
accessories
Lamp unit 1
AN-PH7LP1
AN-PH7LP1
the Lamp Unit
Removing and Installing
Info
Ensure the lamp unit is removed using the
handle. Ensure the glass surface of the
lamp unit or the inside of the projector are
not touched.
To avoid injury to yourself and damage to
the lamp, make sure you carefully follow
the steps below.
Do not loosen other screws except for the
lamp unit cover and lamp unit.
(Only the silver screws are loosened.)
handle. Ensure the glass surface of the
lamp unit or the inside of the projector are
not touched.
To avoid injury to yourself and damage to
the lamp, make sure you carefully follow
the steps below.
Do not loosen other screws except for the
lamp unit cover and lamp unit.
(Only the silver screws are loosened.)
1
Press
on the projector or
on the remote control to put
the projector into standby mode.
Wait until the cooling fan stops.
Warning!
Do not remove the lamp unit from the
projector right after use. The lamp and
parts around the lamp will be very hot
and may cause burn or injury.
projector right after use. The lamp and
parts around the lamp will be very hot
and may cause burn or injury.
2
Disconnect the power cord.
Unplug the power cord from the AC
socket.
Leave the lamp until it has fully cooled
down (about 1 hour).
socket.
Leave the lamp until it has fully cooled
down (about 1 hour).
3
Remove the lamp unit cover.
Loosen the user service screw (
) that
secures the lamp unit cover. Remove the
lamp unit cover (
lamp unit cover (
).
STANDBY button
1
1
2
2
User service screw
Lamp unit 2
AN-PH7LP2
AN-PH7LP2
XG-PH70X/XG-PH70X-N
1 – 14
Regarding the Lamp
4
Remove the lamp unit.
Loosen the securing screws (two for
each lamp) from the lamp unit. Hold the
lamp unit by the handle and pull it in the
direction of the arrow. At this time, keep
the lamp unit horizontal and do not tilt it.
each lamp) from the lamp unit. Hold the
lamp unit by the handle and pull it in the
direction of the arrow. At this time, keep
the lamp unit horizontal and do not tilt it.
5
Insert the new lamp unit.
Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
Be sure that AN-PH7LP1 and AN-
PH7LP2 are respective type.
unit compartment. Fasten the securing
screws.
Be sure that AN-PH7LP1 and AN-
PH7LP2 are respective type.
6
Replace the lamp unit cover.
Align the lamp unit cover and slide it to
close. Then tighten the user service
screw to secure the lamp unit cover.
close. Then tighten the user service
screw to secure the lamp unit cover.
Info
If the lamp unit and lamp unit cover are not
correctly installed, the power will not turn
on, even if the power cord is connected to
the projector.
correctly installed, the power will not turn
on, even if the power cord is connected to
the projector.
Securing screws
Handle
Compartment for
AN-PH7LP1
AN-PH7LP1
Compartment for
AN-PH7LP2
AN-PH7LP2
AN-PH7LP2
AN-PH7LP1
For Lamp 1
For Lamp 2
User service screw
XG-PH70X/XG-PH70X-N
1 – 15
ON button
ENTER button
MENU button
H&V LENS
SHIFT
button
SHIFT
button
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
1
Connect the power cord.
Plug the power cord into the AC socket
of the projector.
of the projector.
2
Reset the lamp timer.
For Lamp 1
When you reset the timer for AN-
PH7LP1, while simultaneously holding
PH7LP1, while simultaneously holding
down
and
, press
on the
projector.
"LAMP 1 100%" is displayed, indicating
that the lamp timer is reset.
"LAMP 1 100%" is displayed, indicating
that the lamp timer is reset.
For Lamp 2
When you reset the timer for AN-
PH7LP2, while simultaneously holding
PH7LP2, while simultaneously holding
down
and
, press
on the
projector.
"LAMP 2 100%" is displayed, indicating
that the lamp timer is reset.
"LAMP 2 100%" is displayed, indicating
that the lamp timer is reset.
To AC socket
Power cord
XG-PH70X/XG-PH70X-N
1 – 15
ON button
ENTER button
MENU button
H&V LENS
SHIFT
button
SHIFT
button
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
1
Connect the power cord.
Plug the power cord into the AC socket
of the projector.
of the projector.
2
Reset the lamp timer.
For Lamp 1
When you reset the timer for AN-
PH7LP1, while simultaneously holding
PH7LP1, while simultaneously holding
down
and
, press
on the
projector.
"LAMP 1 100%" is displayed, indicating
that the lamp timer is reset.
"LAMP 1 100%" is displayed, indicating
that the lamp timer is reset.
For Lamp 2
When you reset the timer for AN-
PH7LP2, while simultaneously holding
PH7LP2, while simultaneously holding
down
and
, press
on the
projector.
"LAMP 2 100%" is displayed, indicating
that the lamp timer is reset.
"LAMP 2 100%" is displayed, indicating
that the lamp timer is reset.
To AC socket
Power cord
