DOWNLOAD Sharp XG-NV5XE (serv.man50) Service Manual ↓ Size: 2.74 MB | Pages: 53 in PDF or view online for FREE

• Used to automatically adjust a computer image.
• Auto Sync adjustment can be made manually by

pressing 

 on the projector or the “Power”

remote control, or automatically by setting “Auto Sync”
to “ON” in the projector’s GUI menu.

• The sync adjustment is automatically made each time

the projector is turned on while connected to a com-
puter or the input selection is changed.

• The Auto Sync adjustment setting previously made is

cleared when the projector’s setting is changed.

(For use with the “Power” remote control, slide the

 switch to the ADJ. position.)

1 Press 

.

2 Press ß/© to select “Fine Sync”.
3 Press ∂/ƒ to select “Auto Sync”.

4 Press ß/© to select “ON”.
5 To exit from the GUI, press 

.

• Automatic adjustments can be made by pressing 

 on the projector or the “Power” remote control.

• When the optimum image cannot be achieved with Auto

Sync adjustment, use manual adjustments. (See the
previous page.)

During Auto Sync adjustment, the On-screen Display
changes as shown on the left.

• Auto Sync adjustment may take some time to complete,

depending on the image of the computer connected to the
projector.

2, 3, 4

1, 5

AUTO SYNC

button

Normally, an image is not superimposed during Auto
Sync adjustment. You can, however, choose to
superimpose a Sharp image during Auto Sync
adjustment.

(For use with the “Power” remote control, slide the

 switch to the ADJ. position.)

1 Press 

.

2 Press ß /©  to select “Options”.
3 Press  ∂/ƒ  to select “Auto Sync Disp”.
4 Press ß /© to select “ ” to superimpose a Sharp

image or “

” to remove the Sharp image during

Auto Sync adjustment.

5 To exit from the GUI, press 

.

g

s

f

This projector allows you to store up to seven adjustment
settings for use with various computers. Once these
settings are stored, they can be easily selected each
time you connect the computer to the projector.

(For use with the “Power” remote control, slide the

 switch to the ADJ. position.)

1 Press 

.

2 Press ß/© to select “Fine Sync”.

3 Press ∂/ƒ to select “Save Setting”, and then press

©.

4 Press ∂/ƒ to select the desired memory location of

the setting.

5 Press 

 to save the setting.

6 To exit from the GUI, press 

.

(For use with the “Power” remote control, slide the

 switch to the ADJ. position.)

1 Press 

.

2 Press ß/© to select “Fine Sync”.
3 Press ∂/ƒ to select “Select Setting”, and then press

©.

4 Press ∂/ƒ to select the desired memory setting.

5 Press 

 to select the setting.

6 To exit from the GUI, press 

.

• If the memory position has not been set, the resolution and frequency

will not be displayed.

• When selecting the stored adjustment setting with “Select Setting”, the

computer system should match the stored setting.

Used to display image in the text and graphic modes.
C

ONNECTING

 

TO

 IBM-PC C

OMPUTERS

• Ordinarily, the type of input signal is detected and the

correct resolution mode (Text or Graphics) is
automatically selected. However, for the following
signals, set “Mode” on the “Fine Sync” menu screen to
“ON” or “OFF” to select the projector’s resolution mode
to match the computer display mode properly.

(For use with the “Power” remote control, slide the

 switch to the ADJ. position.)

1 Press 

.

2 Press ß/© to select “Fine Sync”.
3 Press ∂/ƒ to select “Mode”.

4 Press ß/© to select “ON” for graphic mode (640

dots 

2 350 lines, 640 dots 2 400 lines or 1,152

dots 

2 864 lines,  60 Hz) or “OFF” for text mode

(720 dots 

2 350 lines, 720 dots 2 400 lines or 1,024

dots 

2 864 lines,  60 Hz). (For IBM-PC)

Press  ß/© to select “ON” when connecting to a
Macintosh II with 35 kHz dot frequency or “OFF”
when connecting to a Macintosh LC Series computer
with 34.79 kHz dot frequency. (For Macnitosh LC
Series)

5 Press 

 to save the setting.

6 To exit from the GUI, press 

.

• When connecting third party video board and other Macintosh computers,

set “Mode” on the “Fine Sync” menu screen to “ON” or “OFF” to select the
correct display mode.

• When the input signal is automatically detected or when there is no input

signal, “Mode (---)” appears on the screen and the display mode cannot
be changed.

• Avoid displaying computer patterns which repeat every other line (hori-

zontal stripes). (Flickering may occur, making the image hard to see.)

2

3

4

5

2, 3, 4

1, 6

This function allows you to magnify a specific portion of
an image. This is useful when you want to display a
detailed portion of the image or display it in its native
resolution.

(To use the “Power” remote control to operate this
function, slide the 

 switch to

the ADJ. position before pressing 

.)

1 Press 

. Each time 

 is

pressed, the image will be magnified.

2 When the image is magnified, you can pan and

scan around the image by using ∂/ƒ/ß/©.

• Each time 

 is pressed, image magnification

toggles as shown below.

@

@

@

@

@

@

@

@

@

@

@

@

• If the input signal is changed during digital image

magnification, the image will return to 

21. The input signal

is changed (a) when 

 is pressed, (b)

when there is no input signal, or (c) when the input resolution
and refresh rate changes.

This mode displays images in their native resolution and
not expanded to fit the LCD resolution. See the steps
and the note above to display an image in dot by dot
mode.

LCD PROJECTOR

R/C

OFF

ON

1

2

This function allows you to instantly freeze a moving
image. This is useful when you want to display a still
image of a computer, giving you more time to explain
the image to the audience.

1 Press 

 to freeze the image.

2 Press 

 again to return to the moving

image.

1, 2

sg

This function can be used to superimpose a black
screen over the projected image.

Press 

. “BLACK SCREEN” is dis-

played on the screen. To return to the original projected
image, press 

 again.

• To use the “Power” remote control to operate this function,

slide the 

 switch to the MOUSE

position before pressing 

.

The On-screen Display (“BLACK SCREEN”) that
appears during black screen can be turned off. When
“BLK SCRN Disp” is set to “

” in the projector’s GUI

menu, “BLACK SCREEN” will not be displayed during
function.

(For use with the “Power” remote control, slide the

 switch to the ADJ. position.)

1 Press 

.

2 Press ß /©  to select “Options”.

3 Press  ∂/ƒ  to select “BLK SCRN Disp”.
4 Press  ß/©  to select “ ” to turn on or “ ” to

turn off the function.

5 To exit from the GUI, press 

.

2, 3, 4

1, 5

This function allows you to turn off the on-screen
messages that appear during “input select” and the
“IrCOM” function. Once “OSD Display” is set to “

” in

the projector’s GUI menu, the on-screen messages will
not appear when 

 and 

 on the projector or

the “Power” remote control are pressed.

(For use with the “Power” remote control, slide the

 switch to the ADJ. position.)

1 Press 

.

2 Press ß/© to select “Options”.
3 Press ∂/ƒ to select “OSD Display”.

4 Press ß/© to select “ ” to turn on or “ ” to turn

off the On-screen Display.

5 To exit from the GUI, press 

.

2, 3, 4

1, 5

BLACK

SCREEN

button

sg