DOWNLOAD Sharp XG-MB67X (serv.man18) Service Manual ↓ Size: 4.22 MB | Pages: 69 in PDF or view online for FREE

L

R

To video output terminal

To audio output terminal

Composite video cable
(commercially available)

RCA audio cable (com-
mercially available)

To AUDIO (INPUT

3, 4) terminal

To INPUT4
terminal

You can display computer images on both the projector and a separate monitor using two sets of
RGB cables.

To RGB
input
terminal

To RGB output
terminal

To INPUT 1

terminal

To OUTPUT

(INPUT 1, 2)

terminal

RGB cable (commercially available)

RGB cable

• RGB signals and Component signals can be output to the monitor.
• For this connection, another RGB cable (commercially available) is required.

DVD, etc.

Computer

Monitor

XG-MB67X_EN2_CD_g

06.5.12, 6:44 AM

25

When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-
232C adaptor and an RS-232C serial control cable (cross type, commercially available), the com-
puter can be used to control the projector and check the status of the projector. Refer to the “SETUP
MANUAL” contained on the supplied CD-ROM for details.

To RS-232C terminal

To RS-232C terminal

DIN-D-sub RS-232C
adaptor

RS-232C serial control cable (cross type, commercially available)

• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the

operation manual of the computer for details.

• Refer to page 3 of the “SETUP MANUAL” contained on the supplied CD-ROM for “RS-232C Speci-

fications and Commands”.

• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This

may damage your computer or projector.

• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.

This may damage your computer.

Computer

DIN-D-sub
RS-232C
adaptor

XG-MB67X_EN2_CD_g

06.5.12, 6:44 AM

26

AC socket

Power cord

TX/RX LED (yellow)
Illuminates when transmit-
ting/receiving data.

LINK LED (green)
Illuminates when linked.

Hub

or

Computer

LAN cable (Category 5 type,
commercially available)

To LAN terminal

* To ensure safety, do not

connect the LAN terminal
with any cables that may
cause excessive voltage
such as a telephone line.

• When connecting to a hub, use a straight-through Category 5 (CAT.5) type cable (commercially

available).

• When connecting to a computer, use a cross-over Category 5 (CAT.5) type cable (commercially

available).

To AC outlet

XG-MB67X_EN2_CD_g

06.5.24, 1:53 PM

27

Remove the lens cap and press
S STANDBY/ON on the projector or
fON on the remote control.

• When System Lock is set, the keycode input box

appears. To cancel the keycode setting, input the
keycode that you have already set. See page 

for details.

The lamp indicator illuminates to indicate the
status of the lamp.

Green: The lamp is on.
Blinking in green:The lamp is warming up

or shutting down.

• When switching on the projector, a slight flick-

ering of the image may be experienced within
the first minute after the lamp has been illumi-
nated. This is normal operation as the lamp’s
control circuitry is stabilising the lamp output
characteristics. It should not be regarded as
faulty operation.

• If the projector is put into standby mode and

immediately turned on again, the lamp may
take some time to start projection.

STANDBY/ON button

Lamp indicator

• English is the factory default language. If you

want to change the on-screen display to an-
other language, change the language accord-
ing to the procedure on page 

Note that the connections to external equip-
ment and power outlet should be done be-
fore performing the operations written be-
low. (See pages 

ON button

XG-MB67X_EN2_CD_h

06.5.12, 6:45 AM

28