DOWNLOAD Sharp XG-C55X (serv.man29) Service Manual ↓ Size: 9.04 MB | Pages: 106 in PDF or view online for FREE

When using the default setting.

▼On-screen Display

■ Place a translucent screen between the projector and the au-

dience.

■ Reverse the image by setting “Rear” in “PRJ Mode”. See

 for use of this function.

■ Place a mirror (normal flat type) in front of the lens.

•

When using a mirror, be sure to carefully position both the pro-
jector and the mirror so the light does not shine into the eyes of
the audience.

■ It is recommended that you use the optional Sharp ceiling-mount

bracket for this installation.
Before mounting the projector, contact your nearest Sharp
Authorized Projector Dealer or Service Center to obtain the
recommended ceiling-mount bracket (sold separately).

•

AN-XGCM55 ceiling-mount bracket, its AN-EP101B
extension tube and AN-JT200 universal bracket, adaptor for
non-level ceiling installation (for U.S.A.).

•

BB-M20T ceiling adaptor, its BB-NVHOLDER280,
BB-NVHOLDER550, BB-NVHOLDER900 ceiling mount
systems (for GERMANY).

•

AN-60KT ceiling-mount bracket, its AN-TK201 and AN-TK202
extension tubes (for countries other than the U.S.A. and
GERMANY).

■ Be sure to adjust the position of the pro-

jector to match the distance (H) from the
lens center position (see page 

the lower edge of the image, when
mounting the projector on the
ceiling.

■ Invert the image by setting

“Ceiling + Front” in “PRJ
Mode”. See page 

use of this function.

The image is reversed.

When using the default setting.

▼On-screen Display

The image is inverted.

▼Keycode input box

',", \, |
buttons

', ", \, |
buttons

• The language preset at the factory is English.

If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page 

• The power indicator illuminates red, and

the projector enters the standby mode.

ON

• The power indicator illuminates green.

After the lamp indicator illuminates, the
projector is ready to start operation.

Note

• The lamp indicator illuminates, indi-

cating the status of the lamp.

Green: The lamp is ready.
Green blinking: The lamp is

warming up or
shutting down.

• If the projector is put into the standby

mode and immediately turned on
again, the lamp indicator may take
time to illuminate.

• When controlling the projector using

RS-232C commands from a com-
puter, wait for at least 40 seconds
after the power has been turned on,
and then transmit the commands.

• Enter the keycode.

Note

• When entering the keycode, press

the buttons previously set on the
projector or the remote control.

• When “Anti-Theft” is set, enter the

keycode or the input display will not ap-
pear. Even when the signal is input, the
display will not appear. (see page 

• After pressing   once on the projector,

use 

 to select the desired input mode.

Note

•When no signal is received, “NO

SIGNAL.” will be displayed. When a
signal that the projector is not pre-
set to receive is received, “NOT
REG.” will be displayed.

• When  “Auto Search” is “ON”, the

INPUT modes with signals can be
selected. (see page 

.)

• The INPUT mode is not displayed

when “OSD display” is set to “Level
A” or “Level B”. (see page 

.)

Note

• Pressing 

 will lower the volume.

Pressing 

 will raise the volume.

• On the projector, the volume can be

adjusted by pressing 

 or 

.

•

 , 

 on the projector operate

as cursor buttons (\, |) when the
menu screen is active.

"On-screen Display (Example)

Using RGB

Using
Component

Using
Component

INPUT 3 mode
   Using Video

INPUT 4 mode
   Using S-Video

Using RGB

➝

➝➝

➝

Used for projecting im-
ages from equipment that
sends RGB signals or
component  signals con-
nected to the RGB input
terminal.

Used for projecting im-
ages  from equipment
connected to the VIDEO
input terminal.

Used for projecting im-
ages from equipment
connected to the S-
VIDEO input terminal.

INPUT 1
INPUT 2
(RGB/
Component)

INPUT 3
(Video)

INPUT 4
(S-Video)