Sharp XG-C55X (serv.man29) User Manual / Operation Manual ▷ View online
Connections and Setup
-21
Connecting to an Amplifier
Connecting to an
Amplifier or Other Audio
Components
Amplifier or Other Audio
Components
Using a ø3.5 mm stereo minijack to RCA au-
dio cable, an amplifier or other audio compo-
nents can be connected to the AUDIO OUT-
PUT terminal.
dio cable, an amplifier or other audio compo-
nents can be connected to the AUDIO OUT-
PUT terminal.
Connect the projector to the amplifier
using a ø3.5 mm stereo minijack to
RCA audio cable (commercially
available).
using a ø3.5 mm stereo minijack to
RCA audio cable (commercially
available).
Info
• By using external audio components, the
volume can be amplified for better sound.
• The AUDIO OUTPUT terminal allows you
to output audio to audio components from
the selected AUDIO input terminal (for
INPUT 1 and 2) or AUDIO (L/R) input ter-
minals (for INPUT 3 and 4) connected to
audiovisual equipment.
the selected AUDIO input terminal (for
INPUT 1 and 2) or AUDIO (L/R) input ter-
minals (for INPUT 3 and 4) connected to
audiovisual equipment.
• For details on Variable Audio Output (VAO)
and Fixed Audio Output (FAO), see
page
page
63
.
• A ø3.5 mm stereo minijack to RCA audio
cable (commercially available) is required
for audio input.
for audio input.
Amplifier
Audio input terminal
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
(commercially available)
Connecting to a
Computer Using a DIN-
D-sub RS-232C Adaptor
and an RS-232C Serial
Control Cable
Computer Using a DIN-
D-sub RS-232C Adaptor
and an RS-232C Serial
Control Cable
When the RS-232C terminal on the projector
is connected to a computer with a DIN-D-sub
RS-232C adaptor and an RS-232C serial con-
trol cable (cross type, sold separately), the
computer can be used to control the projec-
tor and check the status of the projector. See
page
is connected to a computer with a DIN-D-sub
RS-232C adaptor and an RS-232C serial con-
trol cable (cross type, sold separately), the
computer can be used to control the projec-
tor and check the status of the projector. See
page
89
for details.
1
Connect the supplied DIN-D-
sub RS-232C adaptor to an RS-
232C serial control cable (sold
separately).
sub RS-232C adaptor to an RS-
232C serial control cable (sold
separately).
2
Use the above cables to con-
nect the projector and the com-
puter.
nect the projector and the com-
puter.
Note
• Do not connect or disconnect an RS-232C
serial control cable to or from the com-
puter while it is on. This may damage your
computer.
puter while it is on. This may damage your
computer.
• The RS-232C function may not operate if
your computer terminal is not correctly set
up. Refer to the operation manual of the
computer for details.
up. Refer to the operation manual of the
computer for details.
• See page
88
for connection of an RS-
232C serial control cable.
Optional
cable
cable
RS-232C serial control cable
AN-C10RS
(32'10" (10.0 m))
AN-C10RS
(32'10" (10.0 m))
RS-232C terminal
DIN-D-sub
RS-232C adaptor
RS-232C adaptor
Supplied
accessory
accessory
Desktop computer
RS-232C serial control cable
(sold separately)
(sold separately)
DIN-D-sub
RS-232C adaptor
RS-232C adaptor
Controlling the Projector by a Computer
-22
Connecting the Projector to Other Devices
Connections and Setup
-23
Optional
cable
cable
Computer RGB cable
AN-C10BM
(32'10" (10.0 m))
AN-C10BM
(32'10" (10.0 m))
Connecting to a Monitor
Watching Images on
Both the Projector and
a Monitor
Both the Projector and
a Monitor
You can display computer images on both the
projector and a separate monitor using two
sets of an RGB cable. An RGB cable is sup-
plied with this projector. You need to buy an-
other RGB cable for connecting the projector
to a monitor.
projector and a separate monitor using two
sets of an RGB cable. An RGB cable is sup-
plied with this projector. You need to buy an-
other RGB cable for connecting the projector
to a monitor.
1
Connect the projector to the
computer and monitor using
RGB cables (one is supplied,
the other is sold separately).
computer and monitor using
RGB cables (one is supplied,
the other is sold separately).
2
In the “Options(1)” menu, se-
lect “Economy Mode”, “Mntr.
out/RS232” and then “ON”.
(see page
lect “Economy Mode”, “Mntr.
out/RS232” and then “ON”.
(see page
69
.)
Note
• Analog RGB signals as well as Component
signals can be output to the monitor.
To RGB input terminal
Monitor
RGB cable
(sold separately)
RGB cable
(supplied)
Desktop computer
To RGB output terminal
Supplied
accessory
accessory
RGB cable
Connecting the Remote
Control to the Projector
Control to the Projector
When the remote control cannot be used due to
the range or positioning of the projector (rear pro-
jection, etc.), connect a ø3.5 mm stereo or mono
minijack cable (commercially available or available
as Sharp service part QCNWGA013WJPZ) from
the WIRED R/C JACK on the top of the remote con-
trol to the WIRED REMOTE control input terminal.
the range or positioning of the projector (rear pro-
jection, etc.), connect a ø3.5 mm stereo or mono
minijack cable (commercially available or available
as Sharp service part QCNWGA013WJPZ) from
the WIRED R/C JACK on the top of the remote con-
trol to the WIRED REMOTE control input terminal.
Note
• FORWARD/BACK presentation control can-
not be used when the remote control is wired
to the projector. To utilize this feature, dis-
connect the cable from the remote control.
to the projector. To utilize this feature, dis-
connect the cable from the remote control.
Using as a Wired Remote Control
ø3.5 mm stereo or mono
minijack cable
(commercially available or
available as Sharp service
part QCNWGA013WJPZ)
minijack cable
(commercially available or
available as Sharp service
part QCNWGA013WJPZ)
To WIRED R/C JACK
WIRED REMOTE control input terminal
-24
Using the Wireless Presentation Function of the
Remote Control
Remote Control
By connecting the remote receiver to a computer, wireless presentation control is possible.
BACK and FORWARD buttons on the remote control will emulate the [Page Up] and [Page
Down] keys on your computer keyboard. This will allow you to remotely navigate applicable
presentation programs such as Microsoft PowerPoint
BACK and FORWARD buttons on the remote control will emulate the [Page Up] and [Page
Down] keys on your computer keyboard. This will allow you to remotely navigate applicable
presentation programs such as Microsoft PowerPoint
®
.
Using the Wireless Pre-
sentation Function
sentation Function
1
Connect the remote receiver to
the computer using the sup-
plied USB cable.
the computer using the sup-
plied USB cable.
Note
• This function only works with the
Microsoft Windows OS and Mac OS.
However, this function does not
work with the following operation
systems that do not support USB.
• Versions earlier than Windows 95.
However, this function does not
work with the following operation
systems that do not support USB.
• Versions earlier than Windows 95.
• Versions earlier than Windows
NT4.0.
• Versions earlier than Mac OS 8.5.
2
Press
or
while using
presentation software on your
computer.
computer.
• Press
to move the page up.
• Press
to move the page down.
Supplied
accessories
accessories
USB cable
Computer
Remote receiver
USB cable
USB terminal
FORWARD
button
button
BACK
button
button
Remote receiver
-24
Connecting the Projector to Other Devices
Click on the first or last page to see other XG-C55X (serv.man29) service manuals if exist.