DOWNLOAD Sharp XG-C40XE (serv.man17) Service Manual ↓ Size: 2.71 MB | Pages: 20 in PDF or view online for FREE

SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should
the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked 

 or 

 and of the same rating as

above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the
mains plug and fit an appropriate type.

DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in
a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious
electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:

IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral
Brown: Live

As the colours of the wires in the mains lead of this product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
• The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
• The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian,
Dutch, Chinese, Korean and Arabic. Carefully read through the operation instructions before operating the LCD
projector.

Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Schwedisch,
Spanisch, Italienisch, Niederländisch, Chinesisch, Koreanisch und Arabisch. Bitte lesen Sie die
Bedienungsanleitung vor der Verwendung des LCD-Projektors sorgfältig durch.

Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, suédois,
espagnol, italien, néerlandais, chinois, coréen et arabe. Veuillez lire attentivement ces instructions avant de faire
fonctionner le projecteur LCD.

Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, svenska, spanska,
italienska, holländska, kinesiska, koreanska och arabiska. Läs noga igenom bruksanvisningen innan projektorn
tas i bruk.

El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, sueco, español,
italiano, holandés, chino, coreano y árabe. Lea cuidadosamente las instrucciones de operación antes de utilizar
el proyector LCD.

Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, svedese, spagnolo, italiano,
olandese, cinese, coreano e arabo. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore LCD.

De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds, Spaans, Italiaans,
Nederlands, Chinees, Koreaans en Arabisch. Lees de handleiding zorgvuldig door voor u de LCD projector in
gebruik neemt.

XG-C40XE/UK

01.8.1, 6:00 PM

2

For your assistance in reporting the loss or theft of your
Colour LCD Projector, please record the Serial Number
located on the bottom of the projector and retain this
information. Before recycling the packaging, please be
sure that you have checked the contents of the carton
thoroughly against the list of “Supplied Accessories”
on page 12.

 

Intense light source. Do not look into the beam or view it directly. Be especially careful
that children do not look directly into the beam.

WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to liquids.

CAUTION:
To reduce the risk of electric shock, do not remove cabinet. No user-serviceable parts
are inside. Refer servicing to qualified service personnel.

WARNING:
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

XG-C40XE/CD (E)-a

01.8.1, 5:49 PM

1

See “Replacing the Projection Lamp” on pages 50 and 51.

The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During
normal operation, when turning the power off always use the POWER buttons. Ensure the cooling fan has
stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER
CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

BEFORE REMOVING THE SCREW,
DISCONNECT POWER CORD.
HOT SURFACE INSIDE. ALLOW
1 HOUR TO COOL BEFORE
REPLACING THE LAMP.
SEE OPERATION MANUAL.

DEBRANCHER LE CORDON
D’ALIMENTATION AVANT DE
RETIRER LES VIS. L’INTERIEUR DU
BOITIER ETANT EXTREMEMENT
CHAUD, ATTENDRE 1 HEURE AVANT
DE PROCEDER A U REMPLACEMENT
DE LA  LAMPE.  SE REPORTER AU
MANUEL D’UTILISATION.

XG-C40XE/CD (E)-a

01.8.1, 5:49 PM

2

For your own protection and prolonged operation of your LCD Projector, be sure to read the following “Important
Safeguards” carefully, before use.
This projector has been engineered and manufactured to ensure your personal safety. But IMPROPER USE CAN
RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards
incorporated into this LCD Projector, observe the following basic rules for its installation, use and servicing.

17. Unplug the LCD Projector equipment from the wall outlet

and refer servicing to qualified service personnel under
the following conditions:

a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the LCD Projector.
c. If the LCD Projector has been exposed to rain or

water.

d. If the LCD Projector does not operate normally

when you follow the operating instructions. Adjust
only those controls that are covered by the oper-
ating instructions, as improper adjustment of other
controls may cause damage and will often require
extensive work by a qualified technician to restore
the LCD Projector to normal operation.

e. If the LCD Projector has been dropped or the

cabinet has been damaged.

f.

When the LCD Projector exhibits a distinct change
in performance—this indicates a need for service.

18. When replacement parts are required, be sure the ser-

vice technician has used replacement parts specified by
the manufacturer that have the same characteristics as
the original parts. Unauthorised substitutions may result
in fire, electric shock, or other hazards.

19. This LCD Projector is provided with one of the following

types of plugs. If the plug should fail to fit into the power
outlet, please contact your electrician.
Do not defeat the safety purpose of the plug.

a. Two-wire type mains plug.

b. Three-wire grounding type mains plug with a

grounding terminal.
This plug will only fit into a grounding type power
outlet.

1. Unplug the LCD Projector from the wall outlet before

cleaning.

2. Do not use liquid cleaners or aerosol cleaners. Use a

damp cloth for cleaning.

3. Do not use attachments not recommended by the LCD

Projector manufacturer, as they may cause hazards.

4. Do not use the LCD Projector near water; for example,

near a bathtub, washbowl, kitchen sink, laundry tub, in a
wet basement, near a swimming pool, etc. Never spill
liquid into the projector.

5. Do not place the LCD Projector on an unstable cart, stand,

or table. The LCD Projector may fall, which may cause
serious injury to a child or an adult, and/or serious damage
to the unit.

6. Wall or Ceiling Mounting—The product should be

mounted to a wall or ceiling only as recommended by
the manufacturer.

7. LCD Projector equipment and cart

combinations should be moved
with care. Quick stops, excessive
force, and uneven surfaces may
cause the equipment and cart
combination to overturn.

8. Slots and openings in the cabinet back and bottom are

provided for ventilation. To ensure reliable operation of
the LCD Projector and to protect it from overheating, these
openings must not be blocked or covered. The openings
should never be covered with cloth or other material.

9. This LCD Projector should never be placed near or over

a radiator or heating vent. The LCD Projector should not
be placed in a built-in installation such as a bookcase
unless proper ventilation is provided.

10. The LCD Projector should be operated only from the type

of power source indicated on the back of the projector or
in the specifications. If you are not sure of the type of
power supplied to your home, consult your LCD Projector
dealer or local power company.

11. Do not place the LCD Projector where the cord will be

abused by persons walking on it.

12. Follow all warnings and instructions marked on the LCD

Projector.

13. To prevent damage to the projector due to lightning and

power-line surges, unplug the projector from the power
outlet, when not in use.

14. Do not overload wall outlets and extension cords with too

many products, because this can result in fire or electric
shock.

15. Never push objects of any kind into the LCD Projector

through the cabinet slots as they may touch high-voltage
points or cause a short circuit. This could result in a fire
or electric shock.

16. Do not attempt to service the LCD Projector yourself.

Opening or removing covers may expose you to dan-
gerous voltage or other hazards. Refer all servicing to
qualified service personnel.

XG-C40XE/CD (E)-a

01.8.1, 5:49 PM

3