DOWNLOAD Sharp PG-M20X (serv.man28) Service Manual ↓ Size: 6.85 MB | Pages: 87 in PDF or view online for FREE

23' (7 m)

30

°

30

°

45

°

■ The remote control can be used to control the projector

Note

• The signal from the remote control can be reflected off a screen

for easy operation. However, the effective distance of the signal
may differ due to the screen material.

• Be sure not to drop, expose to moisture or high temperature.

• The remote control may malfunction under a fluorescent lamp.

Under that circumstance, move the projector away from the fluo-
rescent lamp.

• Insert the batteries making sure the

polarities correctly match the 

 and

 marks inside the battery compart-

ment.

 

• Insert the batteries making sure the polarities correctly match the   and   marks inside the battery compart-

ment.

• Batteries of different types have different properties, therefore do not mix batteries of different types.

• Do not mix new and old batteries.

This may shorten the life of new batteries or may cause old batteries to leak.

• Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak.

Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove
them using a cloth.

• The batteries included with this projector may be used up over a short period, depending on how they are

kept. Be sure to replace them as soon as possible with new batteries.

• Remove the batteries from the remote control if you will not be using the remote control for a long time.

Remote
control
sensor

Signal
transmitter

Remote control

Note

Remote control
RRMCGA013WJSA

Two R-03 batteries
(“AAA” size, UM/SUM-4, HP-16 or similar)

Power cord (6' (1.8m))

For U.S., Canada, etc.
QACCDA007WJPZ

For Europe, except U.K.
QACCV4002CEZZ

For U.K., Hong Kong
and Singapore
QACCBA012WJPZ

For Australia, New
Zealand and Oceania
QACCL3022CEZZ

•

Use the power cord that corresponds to the wall outlet in your country.

DVI to 15-pin D-sub
cable (6' (1.8m))
QCNWGA010WJZZ

USB cable
(6' (1.8 m))
QCNWG0001WJPZ

Carrying case
GCASN0005CESA

Lens cap
(attached)
CCAPHA001WJ01

Lens cap strap
UBNDT0013CEZZ

Terminal cover
(attached)
GCOVD0103CESA

DVI cable (9'10'' (3.0 m))

AN-C3DV

3 RCA to 15-pin D-sub cable (9'10'' (3.0 m)) AN-C3CP
Computer RGB cable (32'10'' (10.0 m))

AN-C10BM
<15-pin mini D-sub male connector>
AN-C10PC
<for PC98 systems (Except PC9821 and PC98NX systems)>

5 BNC to 15-pin D-sub cable (9'10'' (3.0 m)) AN-C3BN
RGB monitor loop-out adaptor (7.9'' (20 cm)) AN-A1MY
DVI to 15-pin D-sub adaptor (7.9'' (20 cm))

AN-A1DV

•

If you cannot connect after changing computer ports, be sure to check you computer’s specifications.
If you are still having difficulty connecting, a conversion connector (commercially available) may be necessary.

Note

•

All cables may not be available in all regions. Please check with your nearest Sharp Authorized
Projector Dealer or Service Center.

CD-ROM
UDSKA0058CEN2

Operation manual
(this manual)

Quick reference guides

(1)

(2)

(3)

(4)

Up

Down

Foot releases

Adjustment feet

Note

• When returning the projector to its origi-

nal position, hold the projector firmly, press
the foot releases and then lower it.

• The projector is adjustable up to approxi-

mately 5.5 degrees from the standard po-
sition.

• Do not press the foot releases when the

feet are extended without firmly holding
the projector.

• Do not hold the lens when lifting or lower-

ing the projector.

• When lowering the projector, be careful not

to get your fingers caught in the area be-
tween the adjustment feet and the projector.