Sharp PG-F150X (serv.man5) User Manual / Operation Manual ▷ View online
27
Basic
Operation
3 Adjusting the Height
The height of the projector can be ad-
justed using the adjustment feet at the
front and rear of the projector.
When the screen is above the projec-
tor, the projection image can be made
higher by adjusting the projector.
justed using the adjustment feet at the
front and rear of the projector.
When the screen is above the projec-
tor, the projection image can be made
higher by adjusting the projector.
1
2
3
• Do not apply too much pressure on the pro-
jector when the front adjustment foot comes
out.
out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
the adjustment foot and the projector.
• Hold the projector firmly while lifting or carrying.
• Do not hold by the lens area.
• Do not hold by the lens area.
Use the rear adjustment foot to
make the projector level.
make the projector level.
• The projector is adjustable ± 2 degree
from the standard position.
Remove your hands from the
HEIGHT ADJUST lever of the pro-
jector after its height has been
finely adjusted.
HEIGHT ADJUST lever of the pro-
jector after its height has been
finely adjusted.
• The angle of projection is adjustable up
to approx. 9 degrees from the surface on
which the projector is placed.
which the projector is placed.
Lift the projector to adjust its
height while lifting the HEIGHT
ADJUST lever.
height while lifting the HEIGHT
ADJUST lever.
Info
• When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the pro-
cedures in Keystone Correction to correct the
distortion. (See pages 28 and 41.)
cedures in Keystone Correction to correct the
distortion. (See pages 28 and 41.)
Note
Rear adjustment foot
HEIGHT
ADJUST lever
ADJUST lever
Make small
adjustments.
adjustments.
PGF150X_E_p25_31.p65
07.5.31, 6:27 PM
27
28
0
KEYSTONE
ADJUST
END
Correcting Trapezoidal
Distortion
Distortion
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is
called Keystone Correction.
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is
called Keystone Correction.
• The Keystone Correction can be adjusted up
to an angle of approximately ± 20 degrees and
the screen can also be set up to an angle of
approximately ± 20 degrees (when the resize
mode is set to “NORMAL” (see page 30)).
the screen can also be set up to an angle of
approximately ± 20 degrees (when the resize
mode is set to “NORMAL” (see page 30)).
Note
1
2
3
Press KEYSTONE.
• The on-screen display of the Keystone
Correction mode will disappear.
• You can also use KEYSTONE on the pro-
jector.
Press P/Q or O/R to adjust the
Keystone Correction.
Keystone Correction.
• You can also adjust the Keystone Cor-
rection using the adjustment buttons on
the projector.
the projector.
Press KEYSTONE to enter the
Keystone Correction mode.
Keystone Correction mode.
• You can also display the on-screen dis-
play of the Keystone Correction mode
with KEYSTONE on the projector.
with KEYSTONE on the projector.
• To return to the default setting, press RETURN
while the on-screen display of the Keystone
Correction mode is on the screen.
Correction mode is on the screen.
Note
On-screen display
(Keystone Correction mode)
(Keystone Correction mode)
Shrinks upper side.
(Move the slide bar in the + direction.)
(Move the slide bar in the + direction.)
Shrinks lower side.
(Move the slide bar in the - direction.)
(Move the slide bar in the - direction.)
Image Projection (Continued)
• While adjusting the image using Keystone
Correction, straight lines and the edges of the
image may appear jagged.
image may appear jagged.
Info
KEYSTONE button
Adjustment buttons
(P/R/O/Q)
(P/R/O/Q)
RETURN button
PGF150X_E_p25_31.p65
07.5.31, 6:27 PM
28
29
Basic
Operation
Displaying the Black Screen
and Turning off the Sound
Temporarily
and Turning off the Sound
Temporarily
Adjusting the Volume
Switching the Input Mode
Press COMPUTER, DVI, S-VIDEO or
VIDEO
VIDEO
on the remote control to select
the input mode.
• When you press INPUT on the projector or DVI
on the remote control, the INPUT list appears.
Press P/R to switch the INPUT mode.
Press P/R to switch the INPUT mode.
Select the appropriate input mode for
the connected equipment.
the connected equipment.
Press VOL +/– on the remote control or
–O
–O
/Q+ on the projector to adjust the vol-
ume.
• Pressing VOL–/–O will lower the volume.
• Pressing VOL+/Q+ will raise the volume.
• When the projector is connected to external
• Pressing VOL+/Q+ will raise the volume.
• When the projector is connected to external
equipment, the volume level of the external equip-
ment changes in accordance with the volume
level of the projector. Set the projector’s volume
to the lowest level when turning the projector on/
off or when changing the input signal.
ment changes in accordance with the volume
level of the projector. Set the projector’s volume
to the lowest level when turning the projector on/
off or when changing the input signal.
• When you do not want to output the sound from
the projector’s speaker while the projector is con-
nected to external equipment, set “Speaker” in
“PRJ-ADJ” menu to “Off”. (See page 43.)
nected to external equipment, set “Speaker” in
“PRJ-ADJ” menu to “Off”. (See page 43.)
Press AV MUTE on the remote control
to temporarily display a black screen
and turn off the sound.
to temporarily display a black screen
and turn off the sound.
• Pressing AV MUTE again will turn the pro-
jected image back on.
On-screen display
Note
Note
On-screen display
VOL +/– (Volume)
buttons
buttons
COMPUTER, DVI,
S-VIDEO, VIDEO
buttons
S-VIDEO, VIDEO
buttons
AV MUTE button
PGF150X_E_p25_31.p65
07.5.31, 6:27 PM
29
30
SVGA (800 K 600)
XGA (1024 K 768)
SXGA (1152 K 864)
SXGA L (1400 K 1050)
SXGA (1280 K 1024)
WXGA (1280 K 768)
1024 K 768
J
768 K 576
J
1024 K 576
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input image. De-
pending on the input signal, you can choose “NORMAL”, “BORDER” or “STRETCH” image.
pending on the input signal, you can choose “NORMAL”, “BORDER” or “STRETCH” image.
Press RESIZE.
• See page 41 for setting on menu screen.
Computer
RESIZE button
Other aspect ratios
4:3 aspect ratio
NORMAL
BORDER
STRETCH
Main resolution
* Mode for projecting an image with the original aspect ratio without cutting any portions.
: Cutout area on which images cannot be projected.
*
*
*
Input Signal
NORMAL
Output screen image
Computer
Image type
BORDER
STRETCH
SXGA
(1280K1024)
WXGA
4:3 aspect ratio
5:4 aspect ratio
16:9 aspect ratio
Resolution lower than
XGA
XGA
Resolution higher than
XGA
PGF150X_E_p25_31.p65
07.5.31, 6:27 PM
30
Click on the first or last page to see other PG-F150X (serv.man5) service manuals if exist.