DOWNLOAD Sharp MX-M905 (serv.man2) Service Manual ↓ Size: 90.97 MB | Pages: 127 in PDF or view online for FREE

MX-M905  ADJUSTMENTS  5 – 81

 

This adjustment is required in the following cases:

* When the U2 trouble occurs.

* When the MFP PWB is replaced.

* When the EEPROM on the MFP PWB is replaced.

* When the SCANNER CONTROL PWB is replaced.

* When the EEPROM on the SCANNER CONTROL PWB is 

replaced.

1)

Enter the Sim. 46-19 mode.

2)

Select the auto mode exposure operating condition of each
mode with the mode button.

 

 

This adjustment is required in the following cases:

* When the manual paper feed tray section is disassembled.

* When the manual paper feed tray section is replaced.

* When the U2 trouble occurs.

* When the PCB PWB is replaced.

1)

Enter the Sim. 40-2 mode.

2)

Open the manual paper feed guide to the maximum width, and
press [EXECUTE] key.

[EXECUTE] key is highlighted. When the maximum width
detection level adjustment value is saved, [EXECUTE] key
returns to the normal display.

3)

Set the manual paper feed guide to the A4 width, and press
[EXECUTE] key.

[EXECUTE] key is highlighted. When the A4 size width detec-
tion level adjustment value is saved, [EXECUTE] key returns
to the normal display.

4)

Set the manual paper feed guide to the A4R width, and press
[EXECUTE] key.

[EXECUTE] key is highlighted. When the A4R size width
detection level adjustment value is saved, [EXECUTE] key
returns to the normal display

5)

Set the manual paper feed guide to the minimum width, and
press [EXECUTE] key.

[EXECUTE] key is highlighted. When the minimum width
detection level adjustment value is saved, [EXECUTE] key
returns to the normal display.

After completion of the adjustment, "COMPLETE" is displayed.

AE_MODE

Auto exposure mode

MODE1

MODE2

MODE2

 MODE3

AE_STOP_COPY

Auto B/W exposure Stop 
(for copy)

REALTIME

PRESCAN

STOP

PRESCAN

AE_STOP_FAX

Auto B/W exposure Stop 
(for FAX)

ON

ON

OFF

AE_STOP_SCAN

Auto B/W exposure Stop 
(for scanner)

REALTIME

STOP

STOP

PRESCAN

AE_FILTER

Auto exposure filter 
setting

SOFT

NORMAL

NORMAL

SHARP

AE_WIDTH

AE exposure width

FULL

FULL

PART

MAX POSITION

Maximum width detection level adjustment

P1 (A4) POSITION

A4 width detection level adjustment

P2 (A4R) POSITION

A4R width detection level adjustment

MIN POSITION

Minimum width detection level adjustment

MX-M905  ADJUSTMENTS  5 – 82

 

This adjustment is required in the following cases:

* When the paper feed tray 4 section is disassembled.

* When the paper feed tray 4 section is replaced.

* When the U2 trouble occurs.

* When the PCU PWB is replaced.

1)

Enter the Sim. 40-12 mode.

2)

Set the paper feed guide to the maximum width, and press
[EXECUTE] key.

[EXECUTE] key is highlighted. When the maximum width
detection level adjustment value is saved, [EXECUTE] key
returns to the normal display.

3)

Set the paper feed guide to the minimum width, and press
[EXECUTE] key.

[EXECUTE] key is highlighted. When the minimum width
detection level adjustment value is saved, [EXECUTE] key
returns to the normal display.

After completion of the adjustment, "COMPLETE" is displayed.

 

This adjustment is required in the following cases:

* When the DSPF paper feed tray section is disassembled.

* When the DSPF paper feed tray section is replaced.

* When the U2 trouble occurs.

* When the scanner PWB is replaced.

* When the EEPROM on the scanner PWB is replaced.

1)

Enter the Sim. 53-6 mode.

2)

Set the DSPF document guide to the maximum width, and
press [EXECUTE] key.

[EXECUTE] key is highlighted. When the maximum width
detection level adjustment value is saved, [EXECUTE] key
returns to the normal display.

3)

Set the DSPF paper feed guide to the A4R width, and press
[EXECUTE] key.

[EXECUTE] key is highlighted. When the A4R size width
detection level adjustment value is saved, [EXECUTE] key
returns to the normal display.

4)

Set the DSPF paper feed guide to the A5R width, and press
[EXECUTE] key.

[EXECUTE] key is highlighted. When the A5R size width
detection level adjustment value is saved, [EXECUTE] key
returns to the normal display. 

5)

Set the DSPF paper feed guide to the minimum width, and
press [EXECUTE] key.

[EXECUTE] key is highlighted. When the minimum width
detection level adjustment value is saved, [EXECUTE] key
returns to the normal display.

After completion of the adjustment, "COMPLETE" is displayed.

MAX POSITION

Maximum width detection level adjustment

MIN POSITION

Minimum width detection level adjustment

TRAYVOLMAX

Maximum width detection level adjustment

TRAYVOLA4R

A4R width detection level adjustment

TRAYVOLA5R

A5R width detection level adjustment

TRAYVOLMIN

Minimum width detection level adjustment

MX-M905  ADJUSTMENTS  5 – 83

 

This adjustment is required in the following cases:

* When the operation panel is replaced.

* When the U2 trouble occurs.

* When the scanner control PWB is replaced.

* When the EEPROM on the scanner control PWB is replaced.

1)

Enter the Sim. 65-1 mode.

2)

Touch the four cross marks on the corners precisely. Do not
use a finger.

When the cross marks are touched precisely, they are
reversely displayed. When the touch panel adjustment is com-
pleted by touching all the four marks, the display returns to the
sub code entry menu.

When touching the cross marks, never use a sharp tip (such
as a needle and a pin).

 

This adjustment is required in the following cases:

* The waste toner detection section has been disassembled.

* One or more parts of the waste toner detection section have

been replaced.

Turn the waste toner detection adjustment knob so that height from
upper surface of the adjustment knob to head edge of the tension
bar is 2.0 mm.

 

This adjustment is required in the following cases:

* When a paper jam occurs in the fusing section.

* When the lead edge of paper is folded in the fusing section.

* When skew is generated in the fusing section.

* When blur or improper focusing is generated on the lead edge

section or the rear edge section of an image on paper. 

* When wrinkle is generated on paper.

1)

Remove the fusing unit.

2)

Loosen the screw.

3)

Slide the fusing paper guide up or down to adjust the position.

* Check and mark the scale position before the adjustment

(with a pencil, etc.), and slide to the left and the right evenly.

2mm

MX-M905  ADJUSTMENTS  5 – 84

4)

Tighten the screw, and fix the fusing paper guide.

5)

Install the fusing unit to the main unit, and check the adjust-
ment result in the copy mode.

* There is no jam.

* The paper lead edge is not folded. 

* There is no skew.

* There is no blur of improper focusing on the lead edge and

the rear edge of an image on paper.

* There is no wrinkle on paper.

 

This adjustment must be performed in the following cases:

* If there occurred a paper jam (POIND_N) with winding around

the Drum when duplex copying.

The ADU section is provided with the decurler (curl correction)
function. The curl correction amount can be adjusted by rotating
the dial.

The adjustment can be made in 9 steps (Default value : 4). The
normally value is 4. The greater the value is from 4, the greater the
correction is.

NOTE: Perform a fine adjustment depending on the paper kind

and the use environment.

The direction of being pointed by the dial which is surrounded with
a 

 is the curl correction amount.

 

 

This adjustment is required in the following cases:

* When the DSPF CCD unit is replaced.

* When a U2 trouble occurs.

* When the DSPF control PWB is replaced.

1)

Check to insure that there is no dirt or dust on the DSPF scan-
ning glass, the mirror, and the lens surface. (If there is, clean it
with alcohol.)

2)

Open the DSPF document scan section, and insert the white
reference jig (PSHEP5859FCZZ). Then, close the DSPF docu-
ment scan section, and close the DSPF.

3)

Enter the SIM 63-2 mode.

4)

Select "DSPF SHADING".

5)

Press [EXECUTE] key. (The shading adjustment process is
started.)

* During shading adjustment, "SHADING EXECUTING..." is

displayed.

* When [EXECUTE] key is pressed during shading adjust-

ment, the operation is interrupted.

* When shading adjustment is completed normally, [EXE-

CUTE] key returns to the normal display and "COMPLETE"
is displayed.

Insert from the notch of the white 
reference jig, and set.

White reference jig set reference 

Insert so that the rear edge of the white 
reference jig is in parallel with the transport roller 
(as shown with the dotted line in the figure).

Insert so that the rear edge of the white reference 
jig is fit with the upper transport PG edge.