Sharp MX-M700U (serv.man7) User Manual / Operation Manual ▷ View online
LOADING PAPER
2-3
2
3
Gently push tray 1-tray 2 into the machine.
Push the tray firmly all
the way into the
machine.
the way into the
machine.
4
Set the paper type.
If the paper size was changed from an AB size to an
inch size, or from an inch size to an AB size, or if the
paper type was changed, be sure to change the
appropriate settings as explained in "Setting the
paper type and paper size" (See page 2-14).
inch size, or from an inch size to an AB size, or if the
paper type was changed, be sure to change the
appropriate settings as explained in "Setting the
paper type and paper size" (See page 2-14).
5
Loading paper in paper tray 1/tray 2 is now
complete.
complete.
Changing the paper size in paper tray 1 - tray 2
To change the paper size of tray 1 - tray 2, follow the steps below.
This section only explains how to change the paper size. For the procedures for opening/closing the tray and loading
paper, see "Loading paper in paper tray 1 - tray 2" (page 2-2).
To have the paper size of tray 1 changed to B5, or to have the paper size of tray 1 changed from B5 to another size,
consult your dealer or nearest authorised service representative. (Only a service technician can change the paper
size in this case.)
This section only explains how to change the paper size. For the procedures for opening/closing the tray and loading
paper, see "Loading paper in paper tray 1 - tray 2" (page 2-2).
To have the paper size of tray 1 changed to B5, or to have the paper size of tray 1 changed from B5 to another size,
consult your dealer or nearest authorised service representative. (Only a service technician can change the paper
size in this case.)
1
Remove the paper size guide.
With the base of the tray pressed all the way down,
hold down the hook at the bottom on the paper
size guide and pull the paper size guide up slightly.
hold down the hook at the bottom on the paper
size guide and pull the paper size guide up slightly.
2
Adjust the paper size guide to the paper
size to be used.
size to be used.
Paper sizes are inscribed at the slot (A) on the
bottom of the tray and at the hole (B) at the top of
the paper size guide. ("LT" indicates 8-1/2" x 11"
size.)
Align the bottom of the paper size guide with the
slot, and align the hole at the top with the locking
tab.
bottom of the tray and at the hole (B) at the top of
the paper size guide. ("LT" indicates 8-1/2" x 11"
size.)
Align the bottom of the paper size guide with the
slot, and align the hole at the top with the locking
tab.
NOTES
● Do not place heavy objects on the tray or press
● Do not place heavy objects on the tray or press
down on the tray.
● Before changing the paper size of tray 1, raise the
paper guide.
Hook
Tray 1
Tray 2
Paper guide
NOTES
● When attaching the paper size guide, make sure
● When attaching the paper size guide, make sure
that the top and bottom of the guide are aligned to
the same paper size.
the same paper size.
● If the top and bottom of the paper size guide are not
aligned to the same paper size, skewed feeding
and misfeeds will result.
and misfeeds will result.
A4
LT
LT
A4
(A)
(B)
LOADING PAPER
2-4
3
Push in the paper guide so that it locks
into place.
into place.
Push the paper size guide in until the hook at the
bottom locks into place. (You will hear a "click"
when the hook locks.) Move the paper size guide
slightly to verify that it has locked into place.
bottom locks into place. (You will hear a "click"
when the hook locks.) Move the paper size guide
slightly to verify that it has locked into place.
4
Repeat steps 1 to 3 to adjust the far paper
guide to the paper size to be used.
guide to the paper size to be used.
Be sure to adjust the far paper guide to the same
size as the near paper guide.
size as the near paper guide.
5
Set the paper type and paper size.
For the procedure for configuring these settings,
see "Setting the paper type and paper size" (page
2-14).
An incorrect paper type or paper size setting may
cause automatic selection of the wrong type or
size of paper, and result in a misfeed or otherwise
prevent printing.
see "Setting the paper type and paper size" (page
2-14).
An incorrect paper type or paper size setting may
cause automatic selection of the wrong type or
size of paper, and result in a misfeed or otherwise
prevent printing.
NOTES
● When removing and attaching the far paper size
● When removing and attaching the far paper size
guide, take care not to hit the front cover of the
machine.
machine.
● Adjust both the front and back guides. If only one
guide is adjusted, skewed feeding and misfeeds
may result.
may result.
LOADING PAPER
2-5
2
Loading paper in paper tray 3
Approximately 500 sheets of standard paper (80
g/m
2
(20 lbs.)) from A3 to A5R size (11" x 17" to 5-1/2" x 8-1/2"R)
can be loaded in tray 3. Special papers such as tabbed paper and transparency film can also be loaded. For
information on what special papers can be used, see "Specifications of paper trays (Types and sizes of paper that
can be used in the trays)" on page 2-12. To load tabbed paper or transparency film, see "Loading tabbed paper" or
"Loading transparency film" on the next page.
information on what special papers can be used, see "Specifications of paper trays (Types and sizes of paper that
can be used in the trays)" on page 2-12. To load tabbed paper or transparency film, see "Loading tabbed paper" or
"Loading transparency film" on the next page.
1
Pull out paper tray 3.
Gently pull the tray out
until it stops.
until it stops.
2
Load paper into the tray.
The paper stack must not
be higher than the
indicator line (no more
than 500 sheets of
SHARP standard paper
(80
be higher than the
indicator line (no more
than 500 sheets of
SHARP standard paper
(80
g/m
2
(20 lbs.)).
To change the paper
size, see "Changing the paper size in paper tray 3"
below.
below.
3
Gently push tray 3 into the machine.
Push the tray firmly all
the way into the
machine.
the way into the
machine.
4
Set the paper type.
If the paper size was changed from an AB size to an
inch size, or from an inch size to an AB size, or if the
paper type was changed, be sure to change the
appropriate settings as explained in "Setting the
paper type and paper size" (see page 2-14).
inch size, or from an inch size to an AB size, or if the
paper type was changed, be sure to change the
appropriate settings as explained in "Setting the
paper type and paper size" (see page 2-14).
5
Loading paper in paper tray 3 is now
complete.
complete.
Changing the paper size in paper tray 3
1
Pull out paper tray 3.
If paper remains in the tray, remove it.
2
Adjust the guide plates A and B by
squeezing their lock levers and sliding
them to the paper size to be loaded.
squeezing their lock levers and sliding
them to the paper size to be loaded.
The guide plates A and
B are slidable. Adjust
them to the paper size to
be loaded while
squeezing their lock
levers.
B are slidable. Adjust
them to the paper size to
be loaded while
squeezing their lock
levers.
3
Load paper into the tray.
4
Gently push tray 3 into the machine.
Push the tray firmly all the way into the machine.
5
Set the paper type of the paper that was
loaded in tray 3.
loaded in tray 3.
Be sure to change the appropriate settings as
explained in "Setting the paper type and paper size"
(see page 2-14).
If you changed the paper size, be sure to change
the paper size setting. An incorrect paper size
setting will cause the wrong paper to be
automatically selected and may prevent printing or
cause misfeeds.
explained in "Setting the paper type and paper size"
(see page 2-14).
If you changed the paper size, be sure to change
the paper size setting. An incorrect paper size
setting will cause the wrong paper to be
automatically selected and may prevent printing or
cause misfeeds.
6
Changing the paper size in paper tray 3 is
now complete.
now complete.
LOADING PAPER
2-6
■ Loading tabbed paper
When using tabbed paper, follow the steps below to attach the special guide to the divider plate at the bottom
edge of the tabbed paper. (Tabbed paper cannot be used in tray 4.)
edge of the tabbed paper. (Tabbed paper cannot be used in tray 4.)
1
Take out the tabbed paper guide.
The guide is stored
inside the left side of the
machine as shown.
Be sure to replace the
guide when you have
finished using it.
inside the left side of the
machine as shown.
Be sure to replace the
guide when you have
finished using it.
2
Pull out the tray and attach the guide.
Slide the divider plate to
the position of the
bottom edge of the
tabbed paper and attach
the guide so that it
covers the divider plate.
the position of the
bottom edge of the
tabbed paper and attach
the guide so that it
covers the divider plate.
3
Place the tabbed paper in the tray.
Place the tabbed paper
with the print side face
up.
with the print side face
up.
[Example]
Make sure that the positions of the tabs correspond
with the originals as shown below.
Make sure that the positions of the tabs correspond
with the originals as shown below.
4
Gently push the tray in and set the paper
type to tabbed paper.
type to tabbed paper.
(See "Setting the paper type and paper size" on
page 2-14)
page 2-14)
■ Loading transparency film
Be sure to load transparency film with the label facing down and the film oriented vertically. Smudging and a
dirty image may result if the film is loaded with the label facing up. (Transparency film cannot be used in tray 4.)
dirty image may result if the film is loaded with the label facing up. (Transparency film cannot be used in tray 4.)
Changing the paper size in paper tray 4
Plain paper from A3 to B5 size (11" x 17" to 7-1/4" x 10-1/2"R) can be loaded in tray 4. For paper that can be used,
see "Specifications of paper trays (Types and sizes of paper that can be used in the trays)" on page 2-12.
The procedures for loading paper in tray 4 and changing the paper size are the same as for tray 3 (see page 2-5).
see "Specifications of paper trays (Types and sizes of paper that can be used in the trays)" on page 2-12.
The procedures for loading paper in tray 4 and changing the paper size are the same as for tray 3 (see page 2-5).
ABC
DEF
GHI
JKL
Front side
1st page
1st page
2nd page
2nd page
3rd page
3rd page
4th page
4th page
Tabbed paper
Original
NOTE
When referring to the explanations of tray 3, keep in mind that special papers such as tabbed paper and
transparency film cannot be used in tray 4. Use tray 3 for special paper.
transparency film cannot be used in tray 4. Use tray 3 for special paper.
Click on the first or last page to see other MX-M700U (serv.man7) service manuals if exist.