DOWNLOAD Sharp MX-M623U / MX-M753U (serv.man10) Service Manual ↓ Size: 49.81 MB | Pages: 127 in PDF or view online for FREE

MX-M753N  SIMULATION  6 – 21

 

24-30

Data clear

Function (Purpose) Used to initialize the administrator pass-

word.

Operation/Procedure
1)

Press [EXECUTE] key.

2)

Press [YES] key.
The administrator password is initialized.

If the administrator password of system setting and Web page is
forgotten, execute this simulation to set the password to "admin"
(default).

 

24-31

Data clear

Function (Purpose) Used to initialize the service mode (Web

page) password.

Operation/Procedure
1)

Press [EXECUTE] key.

2)

Press [YES] key.
The service mode password is initialized.

If the password of Web page is forgotten, execute this simulation to
set the password to "service" (default).

 

 

25-1

Operation test/check

Function (Purpose) Used to check the operations of the devel-

oping section, and to display the toner den-
sity detection level.

Process (Developing section)

Operation/Procedure
1)

Select the process speed with the touch panel key.

2)

Press [EXECUTE] key.
The developing motor and the OPC drum motor rotate for 3
minutes and the output level of the toner density sensor is dis-
played.

 

25-2

Setting

Function (Purpose) Used to make the initial setting of toner

density when replacing developer. (Auto-
matic adjustment)

Process (Photoconductor/Developing/
Transfer/Cleaning)

Operation/Procedure
1)

Press [EXECUTE] key.

The developing motor rotates for 3 minutes, and the toner density
sensor makes sampling of the toner density. The detected level is
displayed.
After stopping the developing motor, the average value of the toner
density sampling results is set as the reference toner density con-
trol level.

NOTE: When the above operation is interrupted on the way, the

reference toner concentration level is not set. Also when
error code of EE-EC, EE-EL or EE-EU is displayed, the ref-
erence toner density level is not set normally.

Do not execute this simulation unless new Developer material has
been installed. If it is executed in other cases, under toner or over-
tone may occur, causing a trouble.

 

 

26-2

Setting

Function (Purpose) Used to set the paper type and the weight

type.

Paper feed

Operation/Procedure
Select a paper size to be changed with the touch panel.

LOW

Process speed: Low speed

MIDDLE

Process speed: Medium speed

TCS

Toner density detection level

TCV_K

Toner density sensor output voltage level

AUTO DV(L)

Toner density adjustment value at the low speed

AUTO DV(M)

Toner density adjustment value at the middle speed

AUTO DV VO(L)

Toner density sensor control voltage level at the low 
speed

AUTO DV VO(M)

Toner density sensor control voltage level at the 
middle speed

TCS

Toner density sensor detection level

TCV

Toner density sensor control voltage level

EE-EL

EL abnormality

Sensor output level less than 26, or 
sensor control voltage level over 197

EE-EU

EU abnormality

Sensor output level over 200, or sensor 
control voltage level less than 49

EE-EC

EC abnormality

The sampling level in the automatic 
toner density adjustment is outside of 
108 

 5.

TRAY2

0

8.5 x 11

1

A4

2

B5

A4 LCC

0

8.5 x 11

1

A4

2

B5

G/LBS SET

0

GRAM

1

LBS

MX-M753N  SIMULATION  6 – 22

 

26-3

Setting

Function (Purpose) Used to set the specifications of the auditor.

(Japan only)

Auditor

Operation/Procedure
Select an item to be set with the touch panel.

(*1) Displayed only when EQUITRAC.

Operation 1: 
Standby during setting time of auto clear. Default is 60 seconds,
which can be changed in the system setting.
Operation 2: 
Auto clear is not made.
Operation 3: 
The display is shifted to the initial screen.

 

26-5

Setting

Function (Purpose) Used to set the count mode in A3 (11" x

17") print.

Operation/Procedure
1)

Select an item to be set with [

] [] keys.

2)

Enter the setting value with 10-key 
1 = Count up by 1, 2 = Count up by 2

3)

Press [OK] key.
The set value in step 2) is saved.

 

26-6

Setting

Function (Purpose) Used to set the specifications of the desti-

nation.

Operation/Procedure
1)

Select an item to be set with the touch panel.

2)

Press [EXECUTE] key.
The selected set content is saved.

BUILT-IN 
AUDITOR

P10

Built-in auditor mode 
(standard mode) operation.

P10

EC1

EC1 mode operation

OUTSIDE 
AUDITOR

NONE

No external connection 
vendor is used.

NONE

P VENDOR1

Coin vendor mode 
(Only the copy mode can be 
controlled.)

P VENDOR2

Vendor mode communicating 
with the parallel I/F (for 
DocuLyzer) (Japan only)

VENDOR-EX 
(*1)

Vendor I/F for EQUITRAC

VENDOR-EX 
(MULTI) (*1)

VENDOR-EX + Multi job 
cueing Enable mode

P OTHER

NOT USED

S_VENDOR

Serial vendor mode

DOC ADJ

ON

Support for the auditor in 
document filing print

OFF

OFF

No support for the auditor in 
document filing print

PF ADJ

ON

Continuous printing is 
performed in the duplex print 
mode.
If the remaining money 
expires during continuous 
printing, the sheets in the 
machine are discharged 
without being printed on the 
back surfaces.

OFF

OFF

Continuous printing is not 
performed in the duplex print 
mode. (The remaining 
amount is checked for 
printing every surface in all 
the printing process.)
If the remaining money 
expires during printing, the 
sheet is discharged without 
printing on the back surface.

VENDOR 
MODE (*2)

MODE1

Vendor mode 1

MODE 

3

MODE2

Vendor mode 2

MODE3

Vendor mode 3

COUNTUP 
TIMING

FUSER_IN

When the paper lead edge 
passes the fusing rear 
sensor.

EXIT_

OUT

FUSER_OUT

When the paper rear edge 
passes the fusing rear 
sensor.

EXIT_OUT

When the paper rear edge 
passes the paper exit sensor 
in the main unit, the right tray, 
and the after process unit.

IMS 
CONTROL

ON

There is some restriction in 
the image send mode.

OFF

OFF

There is no restriction in the 
image send mode.

PRINTER 
CONTROL

MODE1

PRINTER CONTROL 
MODE1 (All the items of 
OUTSIDE AUDITOR can be 
selected.)

MODE

1

MODE2

PRINTER CONTROL 
MODE2 (The item of 
OUTSIDE AUDITOR must 
be the value of "P VENDOR 
1" and the other buttons are 
gray out.)

MODE3

PRINTER CONTROL 
MODE3 (The item of 
OUTSIDE AUDITOR must 
be the value of "P OTHER" 
and the other buttons are 
gray out.)

MODE1

Operation 1

Operation 2

Operation 1

MODE2

Operation 1

Operation 1

Operation 1

MODE3

Operation 1

Operation 3

Operation 3

A

TOTAL (B/W)

Total counter (B/W)

2

B

MAINTE (B/W)

Maintenance counter (B/W)

2

C

DEV (B/W)

Developer counter (B/W)

MX-M753N  SIMULATION  6 – 23

 

26-10

Setting

Function (Purpose) Used to set the trial mode of the network

scanner.

Operation/Procedure
1)

Enter the set value with 10-key.

2)

Press [OK] key.
The set value in step 1) is saved.

 

26-18

Setting

Function (Purpose) Used to set Disable/Enable of the toner

save mode operation. 
(For the Japan and the UK versions.)

Operation/Procedure
1)

Select an item to be set with [

] [] keys.

2)

Enter the set value with 10-key.

3)

Press [OK] key.
The set value in step 2) is saved.

 

26-30

Setting

Function (Purpose) Used to set the operation mode corre-

sponding to the CE mark (Europe safety
standards).

Operation/Procedure
1)

Enter the set value with 10-key.

2)

Press [OK] key.
The set value in step 1) is saved.
* Even in Enable state, the control may not be executed due

to the power frequency, etc.

 

26-35

Setting

Function (Purpose) Used to set the trouble history display

mode.

Operation/Procedure
1)

Enter the set value with 10-key.

2)

Press [OK] key.
The set value in step 1) is saved.

 

26-38

Setting

Function (Purpose) Used to set "Print continue" or "Print stop"

when the maintenance timing is reached or
the consumable part life is over.

Operation/Procedure
1)

Enter the set value with 10-key.

2)

Press [OK] key.
The set value in step 1) is saved.

 

26-41

Setting

Function (Purpose) Used to set Enable/Disable of the magnifi-

cation ratio automatic select function (AMS)
in the center binding mode.

Operation/Procedure
1)

Enter the set value with 10-key.

2)

Press [OK] key.
The set value in step 1) is saved.

U.S.A.

United States of America

CANADA

Canada

INCH

Inch series, other destinations

JAPAN

Japan

AB_B

AB series (B5 detection), other destinations

EUROPE

Europe

U.K.

United Kingdom

AUS.

Australia

AB_A

AB series (A5 detection), other destinations

CHINA

China

TRIAL MODE

(0: YES 1: NO)

0

Trial mode setting

1

Trial mode cancel (Default)

A

COPY

0

Copy toner save mode is inhibited.

0

1

Copy toner save mode is allowed

B

PRINTER

0

Printer toner save mode is inhibited.

0

1

Printer toner save mode is allowed.

0

Control allowed

1

Control inhibited

U.S.A

1 (CE not supported)

EUROPE

0 (CE supported)

CANADA

1 (CE not supported)

U.K.

0 (CE supported)

INCH

1 (CE not supported)

AUS.

0 (CE supported)

JAPAN

1 (CE not supported)

AB_A

0 (CE supported)

AB_B

1 (CE not supported)

CHINA

0 (CE supported)

0

Only once display.

1

Any time display.

A

MAINTENANCE 
LIFE OVER

0

Print continue

0

1

Print stop

B

FUSER WEB END 
(0: CONTINUE 
1: STOP)

0

Continue/Stop setting of print 
when the fusing web is end 
(Print Continue)

0

1

Continue/Stop setting of print 
when the fusing web is end 
(Print Stop)

0

AMS Disable

1

AMS Enable

U.S.A

0 (Disable)

EUROPE

1 (Enable)

CANADA

0 (Disable)

U.K.

1 (Enable)

INCH

0 (Disable)

AUS.

0 (Disable)

JAPAN

0 (Disable)

AB_A

0 (Disable)

AB_B

0 (Disable)

CHINA

0 (Disable)

MX-M753N  SIMULATION  6 – 24

 

26-49

Setting

Function (Purpose) Used to set the print speed of postcards

mode.

Operation/Procedure
Select the copy speed mode with the touch panel. (Default: LOW)
When the setting is changed, the paper feed interval in print or
copy in the postcard mode is changed and the job speed is
changed accordingly.
LOW: The paper feed interval is long. (Normal mode)
HIGH: The paper feed interval is short. (when a paper jam occurs,
the number of sheets of jam paper is greater than that in the LOW
mode.)

 

26-50

Setting

Function (Purpose) Used to set the operation specifications

and functions.

Operation/Procedure
1)

Select a target item of setting with [

] [] key on the touch

panel.

2)

Enter the set value with 10-key.

3)

Press [OK] key. (The set value is saved.)

 

26-52

Setting

Function (Purpose) Used to set whether non-printed paper

(insertion paper, cover paper) is counted up
or not.

Operation/Procedure
1)

Enter the set value with 10-key.

2)

Press [OK] key.
The set value in step 1) is saved.

 

26-53

Setting

Function (Purpose) Used to set Inhibit/Allow of the user auto

calibration (gradation, density adjustment)
in the copy mode.

Operation/Procedure
1)

Enter the set value with 10-key.

2)

Press [OK] key.
The set value in step 1) is saved.

 

26-54

Setting

Function (Purpose) Used to set Inhibit/Allow of the user auto

calibration (gradation, density adjustment)
in the print mode.

Operation/Procedure
1)

Enter the set value with 10-key.

2)

Press [OK] key.
The set value in step 1) is saved.

 

26-65

Setting

Function (Purpose) Used to set the limit of the staple process.
Section

Operation/Procedure
Use the touch key to set.
[Target paper size]
<LIMIT SHEETS>
A4, B5, 8.5 x 11, 16K
<LIMIT SHEETS(L)>
(A3, B4, 11 x 17, 8.5 x 14, 8.5 x 13.5, 8.5 x 13.4, 8.5 x 13, 8K, A4R,
8.5 x 11R)

A

BW REVERSE 

0

BW reverse copy Disable

Refer 

to *1

1

BW reverse copy Enable

B

FEED TRAY
COLOR 

0

Paper feed tray color display 
ON during paper feed

0

1

Paper feed tray color display 
OFF during paper feed

U S A

1

CANADA

1

INCH

1

JAPAN

1

AB_B

1

EUROPE

1

U K

0

AUS

1

AB_A

1

CHINA

1

0

Count up

1

No count up

U.S.A

0 (Counted)

CANADA

0 (Counted)

INCH

0 (Counted)

JAPAN

1 (Not counted)

AB_B

0 (Counted)

EUROPE

0 (Counted)

U.K.

0 (Counted)

AUS.

1 (Not counted)

AB_A

0 (Counted)

CHINA

0 (Counted)

0

Inhibit (Default)

1

Allow

0

Inhibit (Default)

1

Allow