DOWNLOAD Sharp MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man18) Service Manual ↓ Size: 19.34 MB | Pages: 117 in PDF or view online for FREE

MX-M503N  AR-SU1  13 – 2

2)

Remove the sensor cover. Remove the stamp case, and
remove the earth cord.

3)

Attach the stamp unit (package part No. 1) to the stamp case
which was removed from the DSPF/RSPF unit with the install-
ing screw (package part No. 4). (Fix it together with the earth
wire.)

4)

Install the stamp case unit, and connect the connector.

5)

Install the sensor cover.

6)

Install the stamp cartridge (package part No. 3).

7)

Install the OC mat, and close the DSPF/RSPF unit.

* If the angle adjustment plate was lowered for installation, lift

the angle adjustment plate, and fix it with the screw, and
close the DSPF/RSPF unit. 

MX-M503N  AR-SU1  13 – 3

1)

Insert the power plug into the power outlet.

2)

Open the front cabinet of the machine, and turn ON the power
switch.

3)

Turn ON the power switch on the operation panel.

4)

Use SIM22-10 to check to confirm that the finish stamp (AR-
SU1) is recognized.

MX-M503N  MX-PB10  14 – 1

MX-M503N

Service Manual

 

1)

To enable the MX-PB10, enter the product key by the key
operation of the copier machine.
a)

Press the system setting key on the operation panel.

b)

Select [Product key input] key display page, and touch the
key. 

c)

Touch the input column.

d)

Enter the product key with numeric key (10-key), and
touch [Registration] key.

2)

After completion of entry of the product key, turn OFF the
power switch on the operation panel. Turn OFF the main
power switch, then turn ON the power switch and the main
power switch again.

3)

Use the attached CD-ROM to install the driver.
For installing procedures, refer to the software setup guide.
Installation of the driver must be performed by the user or the
serviceman with assistance or the user.

1

CD-ROM (Driver)

1

2

Product key sheet (With Application Number)

1

1

2

APPLICATION
NUMBER

MACHINE
SERIAL
NUMBER

PRODUCT
KEY

Please keep below important information.
This information will use for other products.

MX-M503N  MX-PB11  15 – 1

MX-M503N

Service Manual

 

NOTE: When this option is installed to a machine which has been

used by a user, be sure to backup the user data as shown
below.
When the MX-PB11 is installed, the user settings and the
registered data are initialized. (The simulation settings and
the adjustment data are not initialized.)
Before installing the MX-PB11, save the user data. After
completion of installation, the saved data. Must be
restored.
When this option is installed to a new machine, the proce-
dure below is not required.
Once the product key is inputted after installation of the
MX-PB11, the model cannot be changed back to the U
model without HDD. Before entering the product key, how-
ever, the model can be changed back to the U model with-
out HDD. In that case, however, the user settings and the
registered data are initialized.

1)

Use the device cloning function to backup the user setting data
stored in the SRAM and the EEPROM to a PC or USB mem-
ory.
Use the device cloning function on either the system setting or
the Web Page menu to backup the data.

2)

Use the storage backup function to backup the user data
stored in the HDD to a PC or USB memory.
Use the storage backup function on either the system setting
or the Web Page menu to backup the data.

1)

Turn the power switch located on the operation panel to the
"OFF" position.

2)

Open the front cabinet. Turn OFF the power switch in the front
cabinet of the main unit.

3)

Disconnect the power plug of the main unit from the power out-
let.

1

HDD with frame (Included Water mark data)

1

2

HDD fixing screw

4

3

HDD rubber isolator

4

4

Flash ROM (Program 1/Program 2)

2

5

CD-ROM (Driver)

1

6

Product key sheet with Application number

1

5

6

7

1

2

3

4